Advertisement
Quick Links
Paddle Wheel Steamer with Solar
The OPITEC handicraft packs are not toys in a typical off-the-shelf sense, but rather additional teaching and learning
material for educational purposes. This craft pack may only be constructed by children and adolescents under the
guidance and supervision of experienced adults. Not suitable for children under 36 months. Choking hazard!
1
Gear Drive
Engineer's File
ø3
Hand-Drill
Phillips Head
Screwdriver
Content
Quantity
Plywood
1
Plywood
1
Boat Hull
1
Alu-Sheet
1
Polystyrene
1
Gearwheel
2
Gearwheel
1
Solar Gear Kit
1
117.167
Tools Required:
Water-Resi-
stant Wood
Glue
ø1
ø2
ø3
ø5
Drill
Pair of Snips
Please Note
Size (mm)
Description
400x200x3
Base Plate1
300x210x3
Base Plate2
200x200x0,3
Cover
100x100x2
ø 60
ø 20
Stern Rudder
Ruler
Scissors
Sandpaper
Fretsaw
Slot
Machine Vice
Screwdriver
Part-No
1
2
Hull
3
4
Drive
5
Drive
6
7
Drive
8
Pencil
Superglue
Adhesive Tape
Advertisement
Related Manuals for Opitec 117167
Summary of Contents for Opitec 117167
- Page 1 Screwdriver Please Note The OPITEC handicraft packs are not toys in a typical off-the-shelf sense, but rather additional teaching and learning material for educational purposes. This craft pack may only be constructed by children and adolescents under the guidance and supervision of experienced adults. Not suitable for children under 36 months. Choking hazard!
- Page 2 Instructions 117.167 Paddle Wheel Steamer with Solar Gear Drive Content Quantity Size (mm) Description Part-No Solar Cell 1V 250mA Drive Brass Tube 100x3 Guide Shaft Welding Rod 250x2 Shaft/Roof Cardboard Tube ø19,5x65 Chimney Metal Axle 3x70 Fixture Rudder Terminal Insert with Lateral Hole Fixture Rudder Washers 7/3,2...
- Page 3 Instructions 117.167 Paddle Wheel Steamer with Solar Gear Drive Übersetzung: 1:27 Drive shaft Lower casing Double gears Upper casing Motor drive gear Solar Motor Cut one of the welding wires (11) to 120mm and deburr both ends. Put Saw six slots at a distance of 60° with a fretsaw on both cogwheels. the solar gear together as depicted so that it is positioned centrally onto the shaft.
- Page 4 Instructions 117.167 Paddle Wheel Steamer with Solar Gear Drive Glue 1 of the 12 polystyrene pieces (5) with universal glue into each of Bend both aluminum parts (4c+4d) with a diameter of 60 mm around the sawn slots of both cogwheels (6). Next, insert one reducer (17) into the bottle, so that the aluminum strips assume its form the bore of the two cogwheels and slip them over the axle from both sides.
- Page 5 Instructions 117.167 Paddle Wheel Steamer with Solar Gear Drive Now, glue another frame using the parts D1-D4. After letting it dry, Glue the lid/roof onto the cabin and let it dry thoroughly glue it onto the marking lines of piece C. Gauge and cut 145mm off the welding wire (11).
- Page 6 Instructions 117.167 Paddle Wheel Steamer with Solar Gear Drive Connect the red cable to the positive pole and the black one to the ne- Thread the connection cables of the solar motor through the bores of gative pole. Attach both connection cables to the solar cell using the the covering lids/roofs (C+D) and at the same time position the top bolts.
- Page 7 Instructions 117.167 Paddle Wheel Steamer with Solar Gear Drive Plan 1 Base 1...
- Page 9 Instructions 117.167 Paddle Wheel Steamer with Solar Gear Drive Plan 2 Base 1...
- Page 11 Instructions 117.167 Paddle Wheel Steamer with Solar Gear Drive Plan 3 Base 1...
- Page 13 Instructions 117.167 Paddle Wheel Steamer with Solar Gear Drive Plan 1 Base 2...
- Page 15 Instructions 117.167 Paddle Wheel Steamer with Solar Gear Drive Plan 2 Base 2...
- Page 17 Instructions 117.167 Paddle Wheel Steamer with Solar Gear Drive Plan 1 Aluminiumsheet...
- Page 19 Instructions 117.167 Paddle Wheel Steamer with Solar Gear Drive Plan 2 Aluminiumsheet...
Need help?
Do you have a question about the 117167 and is the answer not in the manual?
Questions and answers