Intel SSR316MJ2 Installation Manual
Installation backplane board (fmjbackplane)
Hide thumbs
Also See for SSR316MJ2:
- Installation manual (50 pages) ,
- Manual (24 pages) ,
- Tested hardware and operating system list (16 pages)
Related Manuals for Intel SSR316MJ2
Summary of Contents for Intel SSR316MJ2
- Page 1 ® Intel Storage System SSR316MJ2 Backplane Board (FMJBACKPLANE) Installation Guide Order Number: C75951-001...
- Page 2 Instrucciones de seguridad importantes Lea todas las declaraciones de seguridad y precaución de este documento antes de realizar cualquiera de las instrucciones. Vea Intel Server Boards and Server Chassis Safety Information en http://support.intel.com/support/motherboards/server/safecert.htm. WARNINGS Storage system power on/off: The push-button on/off power switch on the front panel of the storage system does not turn off the AC power.
- Page 3 No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Intel's Terms and Conditions of Sale for such products, Intel assumes no liability whatsoever, and Intel disclaims any express or implied warranty, relating to sale and/or use of Intel products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright or other intellectual property right.
-
Page 4: Table Of Contents
Re-seat Hard Disk Drives in Hard Disk Drive Bays............... 26 Finishing Up .......................... 27 Figures Figure 1. Removing Chassis Cover ....................8 Figure 2. Unseat Hard Disk Drives and Hard Disk Drive Carriers ..........9 ® Intel Storage System SSR316MJ2 Backplane Board... - Page 5 Figure 17. Re-attaching the System Fan Assembly Connectors ..........24 Figure 18. Re-seating Front Panel Board Cables ..............25 Figure 19. Re-seating Hard Disk Drives in Hard Disk Drive Bays..........26 Figure 20. Re-attaching the Chassis Cover ................27 ® Intel Storage System SSR316MJ2 Backplane Board...
- Page 6 ® Intel Storage System SSR316MJ2 Backplane Board...
-
Page 7: About The Backplane Board Assembly
FMJBACKPLANE Backplane Board Assembly The FMJBACKPLANE Backplane Board Assembly consists of the following: ⎯ FMJBACKPLANE Backplane Board mounted within metal housing ⎯ Pre-installed SATA Cables that are already connected to the Backplane Board ® Intel Storage System SSR316MJ2 Backplane Board... -
Page 8: Backplane Board Installation Procedures
C. Loosen the two thumb screws from the top of the chassis cover. See Figure 1. D. Facing the front of the chassis, push the top cover rearward, and then lift it up to remove it. Figure 1. Removing Chassis Cover ® Intel Storage System SSR316MJ2 Backplane Board... -
Page 9: Unseat Hard Disk Drives From Hard Disk Drive Bays
Figure 2. Unseat Hard Disk Drives and Hard Disk Drive Carriers NOTE: If a hard disk is completely removed from the Storage System Console, it must be re- ® installed into the exact same drive bay. Refer to the Intel Storage System SSR316MJ2 Quick Start User’s Guide for more details. -
Page 10: Remove Front Panel Cables From Front Panel Board
C. Remove the Front Panel Cable labeled J1 from its connector receptacle on the front panel board. See Figure 3. D. Remove the front panel power connector from its connector receptacle on the front panel board. See Figure 3. Figure 3. Removing Front Panel Cables ® Intel Storage System SSR316MJ2 Backplane Board... -
Page 11: Remove Phillips Screws From System Fan Assembly
A. Using a Number 1 size Phillips Screwdriver, remove the Phillips screw on each side of the system that holds the system fan assembly in place. See Figure 4. Set these screws aside. They will be re-installed later. Figure 4. Removing Phillips Screws to Release the System Fan Assembly ® Intel Storage System SSR316MJ2 Backplane Board... -
Page 12: Remove Fan Connectors From Baseboard
B. Remove the wire connector for Fan 4 from the baseboard. See Figure 5. C. Remove the wire connector for Fan 5 from the baseboard. See Figure 5. Figure 5. Removing Fan Connectors from the Baseboard ® Intel Storage System SSR316MJ2 Backplane Board... -
Page 13: Remove Fan Assembly From The System And Sata Cables From The Host Bus Adapter Cards
B. Carefully remove the 16 SATA Cable connectors from the three SATA Host Bus Adapter Cards near the back of the system. See Figure 6. Figure 6. Removing System Fan Assembly and SATA Cable Connectors ® Intel Storage System SSR316MJ2 Backplane Board... -
Page 14: Cut The Plastic Ties That House The Sata Cables
Cut the Plastic Ties that House the SATA Cables A. Cut the plastic cable ties that bundle the SATA Cables. See Figure 7. Figure 7. Cutting the Plastic Ties that House the SATA Cables ® Intel Storage System SSR316MJ2 Backplane Board... -
Page 15: Remove I 2 C Cables From Backplane Board
C Cable connector labeled SL4J6 from its I C Cable header in the HBA Card set. See Figure 8. Set the I C Cable connectors on a static-free surface. Figure 8. Removing the I C Cables from the Backplane Board ® Intel Storage System SSR316MJ2 Backplane Board... -
Page 16: Remove Power Distribution Board Module Connectors From Backplane Board
Remove Power Distribution Board Module Connectors from Backplane Board A. Carefully remove the two 12-pin Power Distribution Board Module connectors from the backplane board. See Figure 9. Figure 9. Removing the Power Distribution Board Module Connectors ® Intel Storage System SSR316MJ2 Backplane Board... -
Page 17: Remove Backplane Board From The System
C. Carefully remove the backplane board from the storage system. Pay attention to sharp edges on the backplane board. See Figure 10. Figure 10. Removing the Backplane Board from the System ® Intel Storage System SSR316MJ2 Backplane Board... -
Page 18: Install New Backplane Board
Using a Number 1 size Phillips Screwdriver, screw in the two Phillips screws into each side of the system until the backplane board is installed. See Figure 11. Figure 11. Installing the New Backplane Board in the System ® Intel Storage System SSR316MJ2 Backplane Board... -
Page 19: Re-Connect Power Distribution Board Module Connectors To Backplane Board
Re-connect Power Distribution Board Module Connectors to Backplane Board A. Carefully re-connect the two 12-pin Power Distribution Board Module connectors to the backplane board. See Figure 12. Figure 12. Re-Connecting the Power Distribution Board Module Connectors ® Intel Storage System SSR316MJ2 Backplane Board... -
Page 20: Re-Connect Sata Cables To Hba Cards
SATA Cables were routed. The cables remain on the chassis side of the Host Bus Adapter Cards and connect to the cards from the chassis side. Figure 13. Re-connecting the SATA Cables to the HBA Cards ® Intel Storage System SSR316MJ2 Backplane Board... -
Page 21: Re-Connect The I C Cables
C Cable connector labeled JP7 to its header on the backplane board. Carefully re-connect I C Cable connector labeled SL4J6 to its header in the HBA Card set See Figure 14. Figure 14. Re-connecting the I C Cables ® Intel Storage System SSR316MJ2 Backplane Board... -
Page 22: Re-Insert Fan Assembly Into System
Align the holes on the bottom edge of the system fan assembly with the blue plastic brackets on the bottom of the chassis. Move the system fan assembly into place. See Figure Figure 15. Re-inserting the Fan Assembly into the System ® Intel Storage System SSR316MJ2 Backplane Board... -
Page 23: Re-Attach Fan Assembly To System
A. Using a Number 1 size Phillips Screwdriver, screw in the one Phillips screw on each side of the system into place until the system fan assembly is mounted in the chassis. See Figure Figure 16. Re-attaching the Fan Assembly to the System ® Intel Storage System SSR316MJ2 Backplane Board... -
Page 24: Re-Attach System Fan Assembly Connectors To Baseboard
B. Re-connect the wire connector for Fan 4 to the baseboard. See Figure 17. C. Re-connect the wire connector for Fan 5 to the baseboard. See Figure 17. Figure 17. Re-attaching the System Fan Assembly Connectors ® Intel Storage System SSR316MJ2 Backplane Board... -
Page 25: Re-Seat Front Panel Board Cables
Front Panel Board connector receptacle. The color of the mesh sheath of Front Panel Cable is black. The black Primary IDE Cable connects to the black Front Panel Board connector receptacle. Figure 18. Re-seating Front Panel Board Cables ® Intel Storage System SSR316MJ2 Backplane Board... -
Page 26: Re-Seat Hard Disk Drives In Hard Disk Drive Bays
Slide all sixteen drives into the bays as far as they can go. See Figure 19. B. Use the handles to lock the drives into the bays. See Figure 19. Figure 19. Re-seating Hard Disk Drives in Hard Disk Drive Bays ® Intel Storage System SSR316MJ2 Backplane Board... -
Page 27: Finishing Up
B. Tighten the two thumb screws on the back of the chassis cover. See Figure 20. C. Re-attach the AC power cables. See Figure 20. ® D. You can now power on the Intel Storage System Console. See Figure 20. Figure 20. Re-attaching the Chassis Cover ®... - Page 28 ® Intel Storage System SSR316MJ2 Backplane Board...