Intel SSR316MJ2 Installation Manual
Storage system cable kit
Hide thumbs
Also See for SSR316MJ2:
- Installation manual (49 pages) ,
- Manual (24 pages) ,
- Tested hardware and operating system list (16 pages)
Related Manuals for Intel SSR316MJ2
Summary of Contents for Intel SSR316MJ2
- Page 1 ® Intel Storage System SSR316MJ2 Cable Kit (FMJCABLES) Installation Guide Order Number: C75947-001...
- Page 2 Instrucciones de seguridad importantes Lea todas las declaraciones de seguridad y precaución de este documento antes de realizar cualquiera de las instrucciones. Vea Intel Server Boards and Server Chassis Safety Information en http://support.intel.com/support/motherboards/server/safecert.htm. WARNINGS Storage system power on/off: The push-button on/off power switch on the front panel of the storage system does not turn off the AC power.
- Page 3 No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Intel's Terms and Conditions of Sale for such products, Intel assumes no liability whatsoever, and Intel disclaims any express or implied warranty, relating to sale and/or use of Intel products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright or other intellectual property right.
-
Page 4: Table Of Contents
Re-seat Front Panel Board Cables ..................29 Re-seat Hard Disk Drives in Hard Disk Drive Bays............... 30 Finishing Up .......................... 31 Front Panel Cables Installation Procedures........... 32 Required Tools........................32 Power Down System and Remove Chassis Cover ............... 33 ® Intel Storage System SSR316MJ2 Cable Kit... - Page 5 C Cables..................22 Figure 14. Re-Connecting the Power Distribution Board Module Connectors ......23 Figure 15. Installing the New Backplane Board in the System ...........24 Figure 16. Connecting the SATA Cables to the HBA Cards ............25 ® Intel Storage System SSR316MJ2 Cable Kit...
- Page 6 Figure 37. Re-attaching the Fan Assembly to the System............47 Figure 38. Re-attaching the System Fan Assembly Connectors ..........48 Figure 39. Re-seating Front Panel Board Cables ...............49 Figure 40. Re-attaching the Chassis Cover ................50 ® Intel Storage System SSR316MJ2 Cable Kit...
-
Page 7: About The Cable Kit
FMJCABLES Cable Kit contains 16 SATA Cables, Two IDE Cables, One Front Panel Cable, and Three I C Cables. NOTE ® This document describes how to install the Intel FMJCABLES SATA ® ® Cables, Intel FMJCABLES IDE Cables, the Intel FMJCABLES Front ®... -
Page 8: About This Document
The Intel FMJCABLES Cable Kit contains SATA Cables, Front Panel Cables, and I C Cables. ® The Intel FMJCABLES Installation Guide contains separate installation instructions for each of the three sets of cables. ® Intel Storage System SSR316MJ2 Cable Kit... -
Page 9: Sata Cables Installation Procedures
SATA Cables Installation Procedures Required Tools • Cross-head (Number 1 Size Phillips ) screwdriver • Wire cutters ® Intel Storage System SSR316MJ2 Cable Kit... -
Page 10: Power Down System And Remove Chassis Cover
C. Loosen the two thumb screws from the top of the chassis cover. See Figure 1. D. Facing the front of the chassis, push the top cover rearward, and then lift it up to remove it. Figure 1. Removing Chassis Cover ® Intel Storage System SSR316MJ2 Cable Kit... -
Page 11: Unseat Hard Disk Drives From Hard Disk Drive Bays
C. Slide the hard disk drives and hard disk drive carriers at least halfway out of the hard disk drive bays. See Figure 2. It is not necessary to completely remove the hard disk drives from the bays. Figure 2. Unseat Hard Disk Drives and Hard Disk Drive Carriers ® Intel Storage System SSR316MJ2 Cable Kit... -
Page 12: Remove Front Panel Cables From Front Panel Board
D. Remove the front panel power connector from its connector receptacle on the front panel board. See Figure 3. E. Move the front panel cables from underneath the fan assembly shroud and backplane and away from the front part of the system. Figure 3. Removing Front Panel Cables ® Intel Storage System SSR316MJ2 Cable Kit... -
Page 13: Remove Phillips Screws From Fan Assembly
See Figure 4. Set these screws aside. They will be re-installed later. Figure 4. Removing Phillips Screws to Release the Fan Assembly ® Intel Storage System SSR316MJ2 Cable Kit... -
Page 14: Remove Fan Connectors From Baseboard
B. Remove the wire connector for Fan 4 from the baseboard header labeled J4K2. See Figure 5. C. Remove the wire connector for Fan 5 from the baseboard header labeled J4K4. See Figure 5. Figure 5. Removing Fan Connectors from the Baseboard ® Intel Storage System SSR316MJ2 Cable Kit... -
Page 15: Remove Fan Assembly From The System And Sata Cables From The Host Bus Adapter Cards
Cards near the back of the system. Make a note of the number labels on each SATA Cable. The new SATA Cables will connect to the SATA Host Bus Adapter Cards in the same numeric order. See Figure 6. Figure 6. Removing Fan Assembly and SATA Cable Connectors ® Intel Storage System SSR316MJ2 Cable Kit... -
Page 16: Remove I C Cables From System
C Cable connector labeled SL4J6 from its I C Cable header in the HBA Card set. See Figure 7. Set the I C Cable connectors on a static-free surface. Figure 7. Removing the I C Cables from the Backplane Board ® Intel Storage System SSR316MJ2 Cable Kit... -
Page 17: Remove Power Distribution Board Module Connectors From Backplane Board
Remove Power Distribution Board Module Connectors from Backplane Board A. Carefully remove the two 12-pin Power Distribution Board Module connectors from the backplane board. See Figure 8. Figure 8. Removing the Power Distribution Board Module Connectors ® Intel Storage System SSR316MJ2 Cable Kit... -
Page 18: Cut The Plastic Ties That Bundle The Sata Cables
Cut the Plastic Ties that Bundle the SATA Cables A. Cut the plastic cable ties that bundle the SATA Cables. See Figure 9. Figure 9. Cutting the Plastic Ties that Bundle the SATA Cables ® Intel Storage System SSR316MJ2 Cable Kit... -
Page 19: Remove Backplane Board From The System
C. Carefully remove the backplane board from the storage system. Pay attention to sharp edges on the backplane board. See Figure 10. Figure 10. Removing the Backplane Board from the System ® Intel Storage System SSR316MJ2 Cable Kit... -
Page 20: Remove Backplane Board From Metal Shroud
See Figure 11. C. Remove all SATA Cable connectors from the backplane board. Remove the SATA Cables from the system. Figure 11. Removing the Backplane Board from the Metal Shroud ® Intel Storage System SSR316MJ2 Cable Kit... -
Page 21: Install Sata Cables To Existing Backplane Board
C. Using a Number 1 size Phillips Screwdriver, screw in the two Phillips screws on each side of the backplane board that hold the backplane board in its metal shroud. See Figure 12. Figure 12. Installing New Backplane Board into Metal Shroud ® Intel Storage System SSR316MJ2 Cable Kit... -
Page 22: Re-Connect The I 2 C Cables
C Cable connector labeled JP7 to its header on the backplane board. Carefully re-connect I C Cable connector labeled SL4J6 to its header in the HBA Card set See Figure 13. Figure 13. Re-connecting the I C Cables ® Intel Storage System SSR316MJ2 Cable Kit... -
Page 23: Re-Connect Power Distribution Board Module Connectors To Backplane Board
Re-connect Power Distribution Board Module Connectors to Backplane Board A. Carefully re-connect the two 12-pin Power Distribution Board Module connectors to the backplane board. See Figure 14. Figure 14. Re-Connecting the Power Distribution Board Module Connectors ® Intel Storage System SSR316MJ2 Cable Kit... -
Page 24: Re-Install Backplane Board
Using a Number 1 size Phillips Screwdriver, screw in the two Phillips screws into each side of the system until the backplane board is installed. See Figure 15. Figure 15. Installing the New Backplane Board in the System ® Intel Storage System SSR316MJ2 Cable Kit... -
Page 25: Connect Sata Cables To Hba Cards
See Figure 16. A total of seven new plastic cable ties should be used. Figure 16. Connecting the SATA Cables to the HBA Cards ® Intel Storage System SSR316MJ2 Cable Kit... -
Page 26: Re-Insert Fan Assembly Into System
Move the fan assembly into place. See Figure 17. Figure 17. Re-inserting the Fan Assembly into the System ® Intel Storage System SSR316MJ2 Cable Kit... -
Page 27: Re-Attach Fan Assembly To System
A. Using a Number 1 size Phillips Screwdriver, screw the Phillips screw on each side of the system into place so that the system fan assembly is mounted in the chassis. See Figure 18. Figure 18. Re-attaching the Fan Assembly to the System ® Intel Storage System SSR316MJ2 Cable Kit... -
Page 28: Re-Attach System Fan Assembly Connectors To Baseboard
B. Re-connect the wire connector for Fan 4 to the baseboard header labeled J4K2. See Figure 19. C. Re-connect the wire connector for Fan 5 to the baseboard header labeled J4K4. See Figure 19. Figure 19. Re-attaching the System Fan Assembly Connectors ® Intel Storage System SSR316MJ2 Cable Kit... -
Page 29: Re-Seat Front Panel Board Cables
Front Panel Board connector receptacle. The color of the mesh sheath of Front Panel Cable is black. The black Primary IDE Cable connects to the black Front Panel Board connector receptacle. Figure 20. Re-seating Front Panel Board Cables ® Intel Storage System SSR316MJ2 Cable Kit... -
Page 30: Re-Seat Hard Disk Drives In Hard Disk Drive Bays
Slide all hard disk drives and drive carriers into the bays as far as they can go. See Figure 21. B. Use the handles to lock the drives into the bays. See Figure 21. Figure 21. Re-seating Hard Disk Drives in Hard Disk Drive Bays ® Intel Storage System SSR316MJ2 Cable Kit... -
Page 31: Finishing Up
B. Tighten the two thumb screws on the back of the chassis cover. See Figure 22. C. Re-attach the AC power cables. See Figure 22. ® D. You can now power on the Intel Storage System SSR316MJ2. See Figure 22. Figure 22. Re-attaching the Chassis Cover ®... -
Page 32: Front Panel Cables Installation Procedures
Front Panel Cables Installation Procedures Required Tools • Wire cutters ® Intel Storage System SSR316MJ2 Cable Kit... -
Page 33: Power Down System And Remove Chassis Cover
C. Loosen the two thumb screws from the top of the chassis cover. See Figure 23. D. Facing the front of the chassis, push the top cover rearward, and then lift it up to remove it. Figure 23. Removing Chassis Cover ® Intel Storage System SSR316MJ2 Cable Kit... -
Page 34: Remove Front Panel Cables From Front Panel Board
C. Remove the Front Panel Cable labeled J1 from its connector receptacle on the front panel board. See Figure 24. D. Remove the front panel power connector from its connector receptacle on the front panel board. See Figure 24. Figure 24. Removing Front Panel Cables ® Intel Storage System SSR316MJ2 Cable Kit... -
Page 35: Remove Front Panel Cables From Baseboard
B. Remove the Secondary IDE Cable connector labeled J1J4 from its connector receptacle on the baseboard. See Figure 25. C. Remove the Front Panel Cable connector labeled J1J2 from its header on the baseboard. See Figure 25. Figure 25. Removing Front Panel Cables from Baseboard ® Intel Storage System SSR316MJ2 Cable Kit... -
Page 36: Install Front Panel Cables On Baseboard
The white Primary IDE Cable connects to the white baseboard connector receptacle. The color of the mesh sheath of Front Panel Cable is black. The black Primary IDE Cable connects to the black baseboard header. Figure 26. Installing Front Panel Cables on Baseboard ® Intel Storage System SSR316MJ2 Cable Kit... -
Page 37: Re-Seat Front Panel Board Cables
C. Re-seat the Primary IDE Cable labeled J5 into its connector receptacle on the front panel board. See Figure 27. D. Re-seat the front panel power connector into its connector receptacle on the front panel board. See Figure 27. Figure 27. Re-seating Front Panel Board Cables ® Intel Storage System SSR316MJ2 Cable Kit... -
Page 38: Finishing Up
B. Tighten the two thumb screws on the back of the chassis cover. See Figure 28. C. Re-attach the AC power cables. See Figure 28. ® D. You can now power on the Intel Storage System SSR316MJ2. See Figure 28. Figure 28. Re-attaching the Chassis Cover ®... -
Page 39: I 2 C Cables Installation Procedures
C. Loosen the two thumb screws from the top of the chassis cover. See Figure 29. D. Facing the front of the chassis, push the top cover rearward, and then lift it up to remove it. Figure 29. Removing Chassis Cover ® Intel Storage System SSR316MJ2 Cable Kit... -
Page 40: Remove Front Panel Cables From Front Panel Board
D. Remove the front panel power connector from its connector receptacle on the front panel board. See Figure 30. E. Move the cables from underneath the fan assembly and backplane and away from the front part of the system. Figure 30. Removing Front Panel Cables ® Intel Storage System SSR316MJ2 Cable Kit... -
Page 41: Remove Phillips Screws From Fan Assembly
See Figure 31. Set these screws aside. They will be re-installed later. Figure 31. Removing Phillips Screws to Release the Fan Assembly ® Intel Storage System SSR316MJ2 Cable Kit... -
Page 42: Remove Fan Connectors From Baseboard
B. Remove the wire connector for Fan 4 from the baseboard. See Figure 32. C. Remove the wire connector for Fan 3 from the baseboard. See Figure 32. Figure 32. Removing Fan Connectors from the Baseboard ® Intel Storage System SSR316MJ2 Cable Kit... -
Page 43: Remove Fan Assembly From The System
A. Simultaneously pull up on both sides of the fan assembly and remove the fan assembly from the storage system. Set the system fan assembly on a static-free surface. See Figure 33. Figure 33. Removing Fan Assembly ® Intel Storage System SSR316MJ2 Cable Kit... -
Page 44: Remove I 2 C Cables From System
C Cable connector labeled SL4J6 from its I C Cable header in the HBA Card set. See Figure 34. Set the I C Cable connectors on a static-free surface. Figure 34. Removing the I C Cables from the Backplane Board ® Intel Storage System SSR316MJ2 Cable Kit... -
Page 45: Installing I C Cables In The System
C Cables in the System ® A. Unpack the new I C Cables that you received in your Intel FMJCABLES Kit. Carefully re- connect the I C Cable connector labeled JP4 to its header on the backplane board. Carefully re- connect I C Cable connector labeled SL2J6 to its header in the HBA Card set. -
Page 46: Re-Insert Fan Assembly Into System
Move the fan assembly into place. See Figure 36. Figure 36. Re-inserting the Fan Assembly into the System ® Intel Storage System SSR316MJ2 Cable Kit... -
Page 47: Re-Attach Fan Assembly To System
A. Using a Number 1 size Phillips Screwdriver, screw the Phillips screw on each side of the system into place so that the system fan assembly is mounted in the chassis. See Figure 37. Figure 37. Re-attaching the Fan Assembly to the System ® Intel Storage System SSR316MJ2 Cable Kit... -
Page 48: Re-Attach System Fan Assembly Connectors To Baseboard
B. Re-connect the wire connector for Fan 4 to the baseboard. See Figure 38. C. Re-connect the wire connector for Fan 5 to the baseboard. See Figure 38. Figure 38. Re-attaching the System Fan Assembly Connectors ® Intel Storage System SSR316MJ2 Cable Kit... -
Page 49: Re-Seat Front Panel Board Cables
Panel Board connector receptacle. The color of the mesh sheath of Front Panel Cable is black. The black Primary IDE Cable connects to the black Front Panel Board connector receptacle. Figure 39. Re-seating Front Panel Board Cables ® Intel Storage System SSR316MJ2 Cable Kit... -
Page 50: Finishing Up
B. Tighten the two thumb screws on the back of the chassis cover. See Figure 40. C. Re-attach the AC power cables. See Figure 40. ® D. You can now power on the Intel Storage System SSR316MJ2. See Figure 40. Figure 40. Re-attaching the Chassis Cover ®...