Advertisement
Available languages
Available languages
Water
Inlet
Hoses
Replace
inlet
hoses
after
5 years
of
use
to
reduce
the
risk
of
hose
failure.
Periodically
inspect
and
replace
inlet
hoses
if
bulges,
kinks, cuts,
wear
or leaks are
found.
When
replacing
your
inlet
hoses, record the date
of
replacement.
Vacation, Storage,
and Mowing
Care
Install
and
store
your
washer where
it
will
not
freeze.
Because
some
water
may
stay
in
the hoses, freezing
can
damage
your
washer.
If
storing or
moving
your
washer
during freezing weather,
winterize
it.
Non-use
or vacation
care:
Operate your washer
only
when
you
are
at
home.
If
you
will
be on
vacation
or not
using
your
washer
for
an extended
period
of
time,
you
should:
Unplug washer
or
disconnect power.
Turn
off
the
water supply
to
the washer. This helps avoid
unintended
flooding
(due
to
a water pressure
surge) while
you
are
away.
Slightly
open
door
to
provide
ventilation.
To
winterize
washer:
1.
Put
1
qt
(1
L)
of
R.V.-type antifreeze
in
the
drum.
2.
Run
washer on
a
Drain
&
Spin
cycle.
3.
Unplug washer
or
disconnect power.
4.
Shut
off
both water
faucets.
5.
Disconnect water
inlet
hoses
from
faucets
and
drain.
To use
washer
again:
1.
Flush
water
pipes.
Reconnect
water
inlet
hoses
to faucets.
Turn
on both water
faucets.
AWARNING
Electrical
Shock
Hazard
Plug
into
a
grounded
3
prong
outlet.
Do
not
remove ground
prong.
Do
not
use an
adapter.
Do
not
use an extension
cord.
Failure to follow
these
instructions
can
result
in
death
fire,
or
electrical
shock.
2.
Plug
in
washer
or
reconnect power.
3.
Run
the
washer
through the Normal/Casual
cycle with
V2
the
manufacturer's
recommended
amount
of
HE
detergent
for
a
medium-size
load, to
clean the
washer and remove
the
antifreeze,
if
used.
To
transport the
washer:
1.
If
washer
will
be
moved
during
freezing
weather, put
in
1
qt
(1
L)
of
R.V.-type antifreeze
in
the
drum.
Run washer
on
a
Drain
&
Spin
cycle.
2.
Unplug
the
power
cord.
3.
Disconnect
the
drain
hose
from
the
drain
system and
attach
to rear
panel
clips.
4.
Shut
off
both water
faucets.
5.
Disconnect
the
water
inlet
hoses from
faucets,
then
drain
the
hoses and
clip
them
to
the
rear
panel
of
the washer.
IMPORTANT:
Call for service.
Do
not
reuse
transport
bolts.
Washer must be
transported
in
the
upright
position.
To
avoid
suspension
and
structural
damage
to
your washer,
it
must be
properly set
up
for
relocation
by
a
certified
technician.
Reinstalling
the
washer
1.
Follow the
"Installation
Instructions" to locate,
level
and
connect
the washer.
2.
Run
the
washer
through the Normal/Casual
cycle with
Vz
the
manufacturer's
recommended
amount
of
HE
detergent
for
a
medium-size
load, to
clean the
washer and remove
the
antifreeze,
if
used.
21
Advertisement
