Related Manuals for BodyCraft Cable Pull Station
Summary of Contents for BodyCraft Cable Pull Station
- Page 1 Assembly and operating instructions 2 persons SWCFT.01.01 Cable Pull Station SW-CFT...
- Page 2 Cable Pull Station...
- Page 3 Dear Customer, Thank you for deciding for a high-quality training equipment of the brand BodyCraft. BodyCraft equipment convinces by multi-functionality and a perfect workmanship and is one of the fitness equipment of highest quality for home use as regards innovation and technology. BodyCraft multi- gyms offer, i.
-
Page 4: Table Of Contents
CONTENTS GENERAL INFORMATION 1.1 Technical data 1.2 Personal safety 1.3 Set-up place ASSEMBLY INSTRUCTIONS, MAINTENANCE AND CARE 2.1 General instructions 2.2 Faults and Troubleshooting 2.3 Maintenance and service calendar ASSEMBLY 3.1 Package contents 3.2 Assembly instructions WARRANTY INFROMATION DISPOSAL ORDERING ACCESSORIES ORDERING SPARE PARTS 7.1 Service hotline 7.2 Serial number and model name... -
Page 5: General Information
GENERAL INFORMATION Technical data Weight and dimensions: Item weight (gross, incl. packaging): Parcel 1 of 2: 49.7 kg Parcel 2 of 2: 28.6 kg Weight stack: 67.5 Kg (15 weight plates à 4.5 kg) Item weight (net, without packaging): 156.3 kg Packaging dimensions boxes (L x W x H): Parcel 1 of 2: 111.8 cm x 61.6 cm x 21.6 cm Parcel 2 of 2: 212.8 cm x 18.5 cm x 12.7 cm... -
Page 6: Personal Safety
Personal safety Before you start using the equipment, you should consult your physician that this type of exercise is suitable for you from a health perspective. Particularly affected are persons who: have a hereditary disposition to high blood pressure or heart disease, are over the age of 45, smoke, have high cholesterol values, are overweight and/or have not exercised regularly in the past year. -
Page 7: Set-Up Place
Set-up place The equipment should only be used indoors, in a sufficiently heated and dry area (ambient temperature between 10°C and 35°C). The equipment should not be used outdoors or in rooms with high humidity (over 70%) like swimming pools. The equipment should only be stored in surroundings with an ambient temperature between 5°C and 45°C. -
Page 8: Assembly Instructions, Maintenance And Care
You should therefore immediately replace damaged or worn components. Please contact your contract partner in such a case. The equipment should no longer be used until it has been repaired. When needed, only use original BodyCraft spare parts. Check the tightness of all screw connections once a month. -
Page 9: Faults And Troubleshooting
Faults and Troubleshooting The equipment runs through regular quality controls during production. Nevertheless, errors or malfunctions on the equipment may occur. Individual parts are often the cause of faults and replacement is usually sufficient. Please use the following overview to see the four most common errors and how to repair them. -
Page 10: Assembly
ASSEMBLY Package contents Before starting assembly, look carefully through the individual assembly steps shown and assemble the equipment in the order indicated. Cable Pull Station... -
Page 12: Assembly Instructions
Assembly instructions Recommended Tools for Assembly Ratchet, 9/16“ Socket, 3/4“ Socket, 9/16“ Combination Wrench, 3/4“ Combination Wrench Adjustable Wrench, Rubber Mallet, Metric Allen Key Set STEP 1 Assemble Main Frame TO EASE THE ASSEMBLY PROCESS DO NOT TIGHTEN BOLTS UNTIL INSTRUCTED. 1. - Page 13 STEP 2 Assemble Main Frame IMPORTANT If you have 19 weight plates, DO NOT install the two stack spacers (24). See figure 1 & 2 below. 1. Refer to figure 1 and 2. If you have 14 weight stack plates (16), install the weight stack spacers (24) onto each guide rod.
- Page 14 STEP 3 Assemble Top Frame 1. Cap four oval caps (27) to the top frame (3). Insert two plastic guide rod holders (18) into the top Frame (3). 2. Attach the pulley bracket (13) to the top frame (3) using one 1/2“ X 1-3/4“ hex threaded bolt (40) and one 1/2“...
- Page 15 STEP 4 Install Cable 1/2 IMPORTANT! Read this page and the next pages in their entirety before completing the cable installation steps 1. Do not tighten the bolts until you are told to do so. 2. The cable installation process involves a single cable but the steps in this manual are divided for clarity.
- Page 16 STEP 4 Install Cable 2/2 Continuing from Step P5, install pulley (19) by halfway removing 3/8“ X 3“ hex bolt (41). Be careful to keep the pulley and the cable located next to it in place. Secure with one 3/8“ nylon nut (59) as shown in block P6.
- Page 17 STEP 5 Assemble Panel & Single Handle & Counter Balance Cord 1. Attach decorative panel (10) to the top frame (3) using two 5/16“ X 1/2“ inner hex screws (46), and two 5/16“ spring washers (46). 2. Route the counter balance cord (31) with the 50mm pulley (20). Attach it to the top frame (3) using one 3/8“...
- Page 18 STEP 6 Assemble Weight Shroud 1. Attach weight shrouds (201) to the top frame (3) and main frame (1) using four 5/16“ X 1/2“ inner hex screws (202) and four 5/16“ washers (203). Remember to keep all bolts loose in the frame to ensure that the holes line up easily. Tighten all bolts. Cable Pull Station...
-
Page 19: Warranty Infromation
WARRANTY INFORMATION BodyCraft fitness equipment is subject to strict quality controls. However, if a fitness equipment purchased from us does not work perfectly, we take it very seriously and ask you to contact our customer service as indicated. We are happy to help you by phone via our service hotline. - Page 20 Warranty service Within the warranty period, equipment which develops faults as a result of material or manufacturing defects, will be repaired or replaced at our discretion. Ownership of equipment or parts of equipment which have been replaced is transferred to us. The warranty period is not extended nor does a new warranty period begin following repair or replacement under the warranty.
-
Page 21: Disposal
DISPOSAL At the end of its operational life, this equipment cannot be disposed of in normal household waste. Instead, it must be disposed of via an electricals recycling centre. Further information can be obtained from your local authority‘s recycling service. The materials can be recycled as per their symbols. -
Page 22: Ordering Spare Parts
Serial number and model name Before assembling your equipment, find the serial number on the white sticker and enter it in the appro- priate space. Serial number: Brand / category: Model name: Article number BodyCraft / weight station Cable Pull Station SW-CFT Cable Pull Station... -
Page 23: Parts List
Parts list Description Qty. No. Description Qty. MAIN FRAME 50mm ROUND CAP BASE FRAME 30mm X 70mm HOLLOW TOP FRAME CABLE CABLE HEIGHT ADJUSTER COUNTER BALANCE CORD FRONT UPRIGHT HANDLE BAR REAR UPRIGHT HANDLE BAR BRACKET GUIDE ROD BUSHING RIGHT SUPPORT FRAME STOPPER LEFT SUPPORT FRAME PLASTIC WASHER... - Page 24 Description Qty. 3/8“ SPRING WASHER 5/16“ SPRING WASHER 3/8“ CURVED WASHER 1/2“ NYLON NUT 3/8“ NYLON NUT M6 NYLON NUT 1/2“ NUT ANKLE STRAP CHAIN 3/4“ X 120L HANDLE GRIP WEIGHT SHROUD 5/16“ X 1/2“ INNER HEX SCREW 5/16“ WASHER Cable Pull Station...
-
Page 25: Exploded Drawing
Exploded drawings... - Page 26 DISCLAIMER Bodycraft is a division of Recreation Supply Inc. 7699 Green Meadows Drive Lewis Center, OH 43035 Product and manual are subject to change. Technical data can be changed without advance notice. Please find a detailed overview including address and opening hours for all specialist fitness stores of the Sport-Tiedje Group in Germany and abroad on the following website.
- Page 27 Notes...
- Page 28 Notes Cable Pull Station...
- Page 30 Cable Pull Station...