Servo And Rf System Adjustment; Cap Fg Duty Adjustment (Vc-359 Board); Switching Position Adjustment (Vc-359 Board) - Sony DCR-HC65 Adjusting Manual

3-3.

SERVO AND RF SYSTEM ADJUSTMENT

Before perform the servo and RF system adjustments, check that
the specified value of "66 MHz Origin Oscillation Check" of
"CAMERA SYSTEM ADJUSTMENT" is satisfied.
And check that the data of page: 0, address: 10 is "00". If not, set
data: 00 to this address.
Adjusting Procedure:
1. CAP FG duty adjustment
2. Switching position adjustment
3. Error rate check

1. Cap FG Duty Adjustment (VC-359 Board)

Set the Cap FG signal duty cycle to 50% to establish an appropriate
capstan servo. If deviated, the uneven rotation of capstan and noise
can occur.
Measurement Point Display data of page: 3, address: 02, 03
Measuring Instrument Adjustment remote commander
Adjustment Page C
Adjustment Address 16
Specified Value Data of page: 3, address: 02 is "00".
Data of page: 3, address: 03 is "00".
Note1: The data of page: 0, address: 10 must be "00".
Adjusting method:
Order Page Address Data
1
2 0 01 01
3 3 01 1B
4 3 02
5 3 03
6 0 01 00
Note2: If the data is "01", adjustment has errors or the mechanism deck is
defective.
Procedure
Close the cassette compartment
without inserting a cassette.
Set the data.
Set the data, and press PAUSE
button.
Check that the data changes in
the following order.
"1B" → "2B" → "00"
Check that the data is "00".
(Note2)
Set the data.

2. Switching Position Adjustment (VC-359 Board)

To obtain normal playback waveform output during the playback
mode, adjust the switching position.
Mode
Signal
Measurement Point
Measuring Instrument
Adjustment Page
Adjustment Address
Specified Value
Note1: The data of page: 0, address: 10 must be "00".
Adjusting method:
Order Page Address Data
1
2 0 01
3 C 10
4 3 21
5 3 01
6 3 02
7 3 03
8 0 01
Note2: If the data of page: 3, address: 21 is "72", the tape top being played.
After playing the tape for 1 to 2 seconds, stop it, perform step 5
and higher.
If the data of page: 3, address: 21 is "62", the tape end being played.
After rewinding the tape, perform step 5 and higher.
Note3: If bit 0 of the data is "1", the EVEN channel is defective. If bit 1 is
"1", the ODD channel is defective. Contents of the defect is written
into page: C, addresses: 10 and 12. See the following table. (For
the bit values, refer to "6-4. SERVICE MODE", "4-3. 4. Bit value
discrimination". ) If bit 3 of the data is "1", the tape end being
played, so rewind the tape and perform the adjustment again.
When the EVEN channel is defective
Data of page: C,
address: 10
EE Writing into EEPROM (IC8802) is defective
E8 Adjustment data is out of range
E7 No data is returned from IC6401
When the ODD channel is defective
Data of page: C,
address: 12
EE Writing into EEPROM (IC8802) is defective
E8 Adjustment data is out of range
E7 No data is returned from IC6401
6-47
DCR-HC65
VTR playback (PLAY/EDIT)
SW/OL reference tape (XH2-3)
Display data of page: 3, address: 02, 03
Adjustment remote commander
C
10, 11, 12, 13
Data of page: 3, address: 02 is "00".
Data of page: 3, address: 03 is "00".
Procedure
Insert the SW/OL reference tape
and enter the VTR STOP mode.
01 Set the data.
EE Set the data, and press PAUSE
button.
Check that the data is "02".
(Note2)
0D Set the data, and press PAUSE
button.
Check that the data changes to
"00".
Check that the data is "00".
(Note3)
00 Set the data.
Contents of defect
Contents of defect