Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for ADLINK Technology ACLD-9182
Summary of Contents for ADLINK Technology ACLD-9182
- Page 1 ACLD-9182 16 Channel Opto-isolated Digital Input Board...
- Page 2 Trademarks ACLD-9182 is registered trademarks of ADLink Technology Inc., PCLD-782 is a trademark of Advantech Co., Ltd. IBM PC is a registered trademark of International Business Machines Corporation. Intel is a registered trademark of Intel Corporation.
-
Page 3: Table Of Contents
How to Use This Guide...........ii 1. Introduction..............1 Features..................1 Applications ................2 Specifications ................2 2. Installation..............3 What You Have ................3 Unpacking...................4 ACLD-9182's Layout..............5 Connector Pin Assignment ............6 Input Mode Setting..............7 ....8 Appendix A. Customize the Current Limit Resistor Product Warranty/Service..........9 Contents • i... -
Page 4: How To Use This Guide
How to Use This Guide This manual is designed to help you use the ACLD-9182. The manual describes how to modify various settings on the ACLD-9182 card to meet your requirements. It is divided into five chapters: • Chapter 1, "Introduction," gives an overview of the product features. -
Page 5: Introduction
LED is off. Each input channel is jumper selectable to either AC or DC input, also, the users do not need to care the polarity. 1.1 Features The ACLD-9182 16 channel opto-isolated D/I board provides the following advanced features: •... -
Page 6: Applications
1.2 Applications : • Industrial ON/OFF control • Laboratory automation • Alarm Control • Motor starter control • Digital signal control • Switch status monitoring 1.3 Specifications: Input channels Opto-coupler PC-814 Input current 50 mA max. for DC input 0~24V or AC 50 ~1,000 Hz Input voltage Logic high : >... -
Page 7: Installation
Installation This chapter describes how to install the ACLD-9182. At first, the contents in the package and unpacking information that you should be careful are described. The jumpers and switches setting for the ACLD-9182's base address and digital input channel configuration (Isolated or Non-isolated) are also specified. -
Page 8: Unpacking
IC's to make sure that they are properly seated. Do this only with the module place on a firm flat surface. Note : DO NOT APPLY POWER TO THE CARD IF IT HAS BEEN DAMAGED. You are now ready to install your ACLD-9182. 4 • Installation... -
Page 9: Acld-9182'S Layout
2.3 ACLD-9182's Layout +12V JP16 JP 8 JP15 JP 7 +15- +14- JP14 JP 6 +13- JP13 JP 5 +12- +11- JP12 JP 4 +10- JP11 JP10 Figure 2.1 Installation • 5... -
Page 10: Connector Pin Assignment
2.4 Connector Pin Assignments The relationship between connector CN1's pins( shown in figure 2.2 below), terminal blocks(TB1 & TB2), LED's, and their related jumpers are shown in the following table ( Table 2.1): DI 0 DI 1 DI 2 DI 3 DI 4 DI 5 DI 6... -
Page 11: Input Mode Setting
** Pin-20 (+12V) depends on the output form digital input connector, such as ACL-8111, ACL-8112 are +12V, and ACL-7120 is strobe signal. 2.5 Input Mode Setting There are 16 jumpers (JP0...JP15) associated with each digital input channel for configuring the channel as AC or DC input. The digital input channels and their corresponding jumpers is shown in the following Table 2.2. -
Page 12: Appendix A. Customize The Current Limit Resistor
Appendix A. Customize the Current Limit Resistor The ACLD-9182 contains 16 identical opto-isolated control input channels. The circuit diagram of the isolated input channel is shown below. The digital input is first routed through a photo-coupler (PC- 814), so that the connection are not polarity sensitive whether used on AC or DC voltage. -
Page 13: Product Warranty/Service
Product Warranty/Service Seller warrants that equipment furnished will be free form defects in material and workmanship for a period of one year from the confirmed date of purchase of the original buyer and that upon written notice of any such defect, Seller will, at its option, repair or replace the defective item under the terms of this warranty, subject to the provisions and specific exclusions listed herein.
Need help?
Do you have a question about the ACLD-9182 and is the answer not in the manual?
Questions and answers