RadioLink T8FB Instruction Manual
  1. Manuals
  2. Brands
  3. RadioLink Manuals
  4. Remote Control
  5. t8fb
  6. Instruction manual

RadioLink T8FB Instruction Manual

Compatible with helicopter/fixed wing/multicopter/car/boat
Hide thumbs Also See for T8FB:
Table of Contents

Advertisement

Quick Links

RadioLink Electronic Ltd
www.radiolink.com
T8FB
(FHSS)
INSTRUCTION MANUAL
Compatible with Helicopter/Fixed Wing/Multicopter/Car/Boat
CE FCC
* Please be kindly noted that this manual will be updated regularly and please visit Radiolink official
website to download the latest version.

Advertisement

Table of Contents
loading

Related Manuals for RadioLink T8FB

Summary of Contents for RadioLink T8FB

  • Page 1 RadioLink Electronic Ltd www.radiolink.com T8FB (FHSS) INSTRUCTION MANUAL Compatible with Helicopter/Fixed Wing/Multicopter/Car/Boat CE FCC * Please be kindly noted that this manual will be updated regularly and please visit Radiolink official website to download the latest version.
  • Page 2 2. PM us on our Facebook page or leave comments on our Youtube page 3. If the product is purchased from RadioLink AliExpress Global or Amazon U.S , you can contact after-sales service directly.

  • Page 3: Table Of Contents

    1.3 Compatible Receivers : R8EF and R8FM ......................5 1.4 Transmitter Calibration............................8 Part 2 Firmware Upgrade..............................9 2.1 Firmware Introduction............................9 2.2 Upgrade Steps..............................9 PART 3 T8FB Parameters Setup via Android Smart-phone APP.................12 3.1 Configuration..............................12 3.2 APP Installation..............................12 3.3 Connection Steps..............................13 3.4 The Functions Introduction..........................14 3.4.1 Setting Buttons Introduction........................15...

  • Page 4: Part 1 Introduction Of T8Fb System

    4S LiPo battery. Defaulted low battery alarm voltage can automatically match 2S and 3S LiPo battery or 4pcs AA batteries, can setting in the T8FB configure software. 3S LiPo battery: default low voltage alarm to 11.0V automatically after detection, you can setup low battery voltage alarm from 10.0V to 12.5V.

  • Page 5: Guidelines To Mount The Servos, Receiver And Battery

    If you accidentally get moisture or fuel inside the receiver,you may experience intermittent operation or a crash. If in doubt, please contact Radiolink after-sales or distributors for service.

  • Page 6: Compatible Receivers : R8Ef And R8Fm

    In addition, periodically check the wire during daily maintenance. 1.3 Compatible Receivers : R8EF and R8FM Radiolink T8FB is sells with 2.4G 8 channels receiver R8EF. R8EF is support S-BUS , PPM and PWM signal working at the same time.
  • Page 7 RadioLink Electronic Ltd www.radiolink.com Specification: 1) Channels: 8 channels 2) Working voltage: 4.8-10V 3) Working current: 30mA（input voltage: 5V） 4) Size: 48.5*21*11mm 5) Weight: 7g 6) 2048 section precision, 0.5us section, servo anti-shake rudder. 7) Control distance: about 500m ground and 1000m air, actually control distance depends on the environment.
  • Page 8 S-BUS&PPM. The red LED indicates the PWM mode while blue/purple LED indicates S-BUS&PPM mode. MINI Receiver R8FM T8FB is also compatible with 2.4G 8 channels supper mini receiver R8FM, which support S-BUS and PPM signal working at the same time, supper mini size, is designed for racing drone. Specification: 1) Channels: 8 channels 2) Working voltage: 4.8-6V...

  • Page 9: Transmitter Calibration

    1. Put the transmitter and the receiver close to each other within 50 centimeters. 2. Power on T8FB and receiver R8EF(or R8FM). The RED LED will start flashing slowly. 3. Turn on T8FB and it will automatically bind with the closest receiver.

  • Page 10: Part 2 Firmware Upgrade

    The USB data backup copy function of T8FB helps save and copy parameter settings easily. 2.1 Firmware Introduction The latest firmware is T8FB_FHSS_V201_a77b_20170609_33bit. We will upgrade firmware according to T8FB users, new firmware will not upgrade in this manual, you can download it from our website: www.radiolink.com 2.2 Upgrade Steps...
  • Page 11 RadioLink Electronic Ltd www.radiolink.com (4) “ Disconnect ” will change to “ Connected ” and the color of word will from red to green if connect successful. (5) Choose “APROM” and then choose the firmware you need.
  • Page 12 RadioLink Electronic Ltd www.radiolink.com (6) Click “Start”, the progress bar will turn to green, upgrade successful if remind “PASS”.

  • Page 13: Part 3 T8Fb Parameters Setup Via Android Smart-Phone App

    3.1 Configuration 1) One USB cable for Android smart-phone The smaller port connect to T8FB USB port and the other bigger port connect to OTG data cable. 2) One OTG cable for Android smart-phone The smaller port connect to smart-phone USB port 3) Android smart-phone system requires to upgrade to version 4.0 or above.

  • Page 14: Connection Steps

    3.3 Connection Steps 1) Turn on the transmitter T8FB at first. 2) Connect USB cable to your phone after installed the APP, it will hint if open “ Radiolink T8FB ” when connection. Attention: Different smart-phone (as OPPO R9s and so on ), you have to turn on the OTG connection...

  • Page 15: The Functions Introduction

    RadioLink Electronic Ltd www.radiolink.com 3.4 The Functions Introduction 1) there are four interfaces in total , ”SERVO”, ”BACIS”, ” ADVANCED”, ”SYSTEM” 2) Every interface will shows the voltage of T8FB.

  • Page 16: Setting Buttons Introduction

    (it is important for your setting ). 4) “ SAVE ” : when you click the button , the APP will save the T8FB data into phone folder “ /model/model01.text ” . App will create a “ model ” folder at smartphone Root directory, then recreate a “model01.text”...

  • Page 17: Four Interface Introduction

    RadioLink Electronic Ltd www.radiolink.com 3.4.2 Four Interface Introduction 1)”SERVO”: Display the servos position of CH1—CH8. 2)”BASIC”: Have six buttons”REV” “SUB” “EPA-L”“EPA-R” “F/S” “DELAY”. “ REV ” : Defines the relationship between the transmitter controls and the receiver output for channels.
  • Page 18 RadioLink Electronic Ltd www.radiolink.com We recommend that you center the digital trims before making SUB-TRIM changes, and that you try to keep all of the SUB-TRIM values as small as possible. Otherwise, when the SUB-TRIM are large values, the servo's range of travel is restricted on one side.
  • Page 19 RadioLink Electronic Ltd www.radiolink.com “D/R”: Set the switch to control the max and min values of channel amount. Dual/Triple Rates: reduce/increase the servo travel by flipping a switch, or (ACRO GLID) they can be engaged by any stick position. Dual rates affect the control listed, such as aileron, not just a single (ex: channel 1) servo.
  • Page 20 RadioLink Electronic Ltd www.radiolink.com Change the response curve of the servos relative to the stick position to make fly more pleasant. You can make the servo movement less or more sensitive around neutral for rudder, aileron, elevator, and throttle (except HELI type use THROTTLE CURVE instead). (ACRO type throttle EXP and THROTTLE CURVE can not be activated simultaneously).
  • Page 21 RadioLink Electronic Ltd www.radiolink.com 0% means a output signal 1ms, and 100% means 2ms. You can totally get 6 different modes by adjusting the related rates. “ELEVON”: Adjust the aileron distance, allow aileron differential. ADJUSTABILITY: • Requires use of CH1 and CH2.

  • Page 22: Faq

    What are the correct steps for the “READ”? In general, please click the “READ” first after connect T8FB to APP to make sure the data of APP is the default data or you setup last time.
  • Page 23 How to find “SAVE” file (/model/model01.text) Find the folder Storage and model How to solve the problem that the APP flashback when you click “LOAD” button. You need to open the permissions. Settings - Permissions - APPS - RadioLink T8FB- Accept.

  • Page 24: Part 4 T8Fb Parameters Setup Via Computer

    4.1 Parameter Configuration Software Setup Steps (1) Open T8FB parameter configuration software.(P1) （P1） (2) Choose Port Number(T8FB connect to COM will automatic identified when connect to computer), setting baud rate: 115200, 8-1-None(8 data bits, 1 stop bit, no parity check), click“CONNECT”.(P2)

  • Page 25: Software Description

    Load configured TXT files. “UPDATE”: Write down the new data you want and then click “ UPDATE ” to change the defaulted parameter. T8FB will remember the new data you have write down(red and green LED will slowly flashing when updating). “SAVE”:...

  • Page 26: Basic Menu

    RadioLink Electronic Ltd www.radiolink.com 4.2.1 BASIC MENU “REVERSE”: Defines the relationship between the transmitter controls and the receiver output for channels. “SUB-TRIM”: Makes small changes or corrections to the neutral position of each servo. “END POINT”: Sets the range of each channel(in percentage);...

  • Page 27: Advacne Menu

    “ATTITUDE”: By changing these figures to output different control signals. “ELEVON”: Adjust the aileron distance, allow aileron differential. “V-TAIL”: Be used on the V-ail aircraft. “PROG.MIX1”: “PROG.MIX2”: Note The detailed introduction about T8FB functions please check on page15: 3.3 The Functions Introduction. Thank you again for using our product.

Table of Contents