Bosch BT-ANGLEEXACT Series Original Instructions Manual page 26

26 | English
life. If used correctly, the battery can withstand up to 3000
charging cycles.
A new battery or one that has not been used for a long time
will only operate at full capacity after approximately five
charge and discharge cycles. Batteries should only be
charged if the battery charge LED indicator on the power
tool lights up red.
Inserting and Removing the Battery
Push the rotational direction switch (13) into the middle po-
sition. This locks the on/off switch (12) in the "Off" position
and prevents the power tool from being switched on unin-
tentionally.
Push a charged battery (18) into the handle of the power
tool.
Make sure that you insert the battery correctly and that you
can feel the release buttons (17) engage in the handle of the
power tool.
Do not use force to insert/remove the battery. Batter-
u
ies with APT contact (Akku Pack Top, English: battery
pack top) are designed such that they can only be inser-
ted into the power tool or charger in the correct position.
To remove the battery (18), press the release buttons (17)
on both sides and pull the battery down and out of the
handle.
Inserting and removing the voltage adapter (see figure
C)
Select the voltage adapter that matches your power tool's
rated voltage.
The voltage adapters can be differentiated by the colour of
the housing of the D-Sub connector plug (26), which differs
according to voltage. The housing of the D-Sub connector
plug for a voltage of 9.6 V is light blue, the one for a voltage
of 14.4 V is black.
The adapter housing (28) may only be fitted on or re-
u
moved from the industrial cordless screwdriver when
the constant voltage regulator is switched off or when
the connector plug (26) is disconnected from the con-
stant voltage regulator.
Push the rotational direction switch (13) into the middle po-
sition. This locks the on/off switch (12) in the "Off" position
and prevents the power tool from being switched on unin-
tentionally.
Then push the adapter housing (28) into the handle of the
power tool. Make sure that you insert the adapter housing
correctly and that you can feel the release buttons (17) en-
gage in the handle of the power tool.
Then insert the connector plug (26) for the voltage adapter
that is compatible with your power tool into the connection
socket (25). Tighten the connector plug (26) in the connec-
tion socket (25) by hand-tightening the two screws (27).
To remove the voltage adapter, loosen the two screws (27)
on the connector plug (26) of the constant voltage regulator
(switched off) and remove the connector plug from the con-
nection socket (25).
Then press the release buttons (17) on both sides and pull
the adapter housing (28) out of the handle of the power tool.
1 609 92A 4V2 | (13.02.2019)
Changing the tool – screw head with quick-
change chuck (see figure D)
When fitting an application tool, make sure that it is
u
held securely in the tool holder. If the application tool is
not held securely in the tool holder, it may become loose
and consequently uncontrollable.
BT-EXACT 2 | 4 | 6 | 7 | 8 | 9 | 12
The BT-EXACT series is supplied with a 1/4" quick-change
chuck (QC 1/4").
BT-ANGLE EXACT 2 | 3 | 6
An angled screw head with a 1/4" quick-change chuck is
available for these industrial cordless angle wrenches (art-
icle number 0 607 453 631).
BT-ANGLE EXACT 2 | 3 | 6 | 7 | 8 | 15
An angled screw head with a 1/4" quick-change chuck is
available for these industrial cordless angle wrenches (art-
icle number 0 607 453 630).
Inserting the application tool
Pull the quick-change chuck (29) forwards. Insert the applic-
ation tool (1) into the tool holder (2) and release the quick-
change chuck again.
Only use application tools with a matching shank (1/4"
hexagon).
Do not attempt to insert drill bits into this quick-change
chuck.
Industrial cordless angle wrenches and industrial cordless
screwdrivers with a shut-off clutch are not suitable for
drilling. The clutch can shut off automatically and without
warning. If you continue drilling after the clutch has shut off,
the power tool may be wrenched out of your grip until the
shut-off clutch engages again.
Removing the application tool
Pull the quick-change chuck (29) forwards. Take the applic-
ation tool (1) out of the tool holder (2) and release the
quick-change chuck again.
Changing the tool – screw head with external
square
When fitting an application tool, make sure that it is
u
held securely in the tool holder. If the application tool is
not held securely in the tool holder, it may become loose
and consequently uncontrollable.
BT-ANGLE EXACT 2 | 3 | 6 | 7 | 8 | 15
An angled screw head with a 1/4" square (article number
0 607 453 617) and an angled screw head with a 3/8"
square (article number 0 607 453 620) are available for
these industrial cordless angle wrenches.
BT-ANGLE EXACT 2 | 7 | 17 | 23 | 30
An angled screw head with a 3/8" square is available for
these industrial cordless angle wrenches (article number
0 607 451 618).
Inserting the application tool
Press the pin on the square of the tool holder (2) inwards,
e.g. using a narrow screwdriver, and slide the application
Bosch Power Tools