Table of Contents
Advertisement
Available languages
Available languages
Quick Links
Limelight by Lutron OEM Integration Guide
This document is intended for luminaire/fixture manufacturers who are integrating Limelight by Lutron
LL-INTMOUNT and LL-PIR-L/M/H modules into their luminaires. It provides recommendations for electrical and
mechanical integration of these modules into a luminaire, and recommended manufacturing test procedures.
1. Standards
• RoHS Compliant
• FCC15.247 / IC RSS-247 (LL-INTMOUNT)
• cULus Recognized for internal mounting at a fixture OEM
• IP66 (wet locations) (LL-PIR-L/M/H) when lens assembly is installed correctly at fixture manufacturer
2. Model Numbers
Model Number
LL-INTMOUNT
LL-PIR-L
LL-PIR-M
LL-PIR-H
3. LL-INTMOUNT Integration
Mechanical Integration
Dimensions shown as: in (mm)
1.12 (28.5)
0.24 (6.19)
0.57 (14.5)
0.24 (6.19)
Holes
Ø2.751 (Ø69.9)
Clearance areas
both sides of PCB
Ø0.23 (Ø5.84)
The LL-INTMOUNT module has multiple holes (diameter = 0.11 in [2.75 mm]) for mounting to a luminaire. The
LL-INTMOUNT should be mounted using a minimum of two of the holes to ensure that the PCB does not
excessively vibrate.
The LL-INTMOUNT should be mounted in a location that is not accessible by the user because parts of the
PCB have a high-voltage and should be out of reach.
The LL-INTMOUNT should be mounted as far away from metal housings and components as possible.
Description
Limelight by Lutron Radio Module PCB Assembly
Limelight by Lutron PIR Sensor Assembly; for 8 to 15 ft (2.5 to 4.6 m) mounting height
Limelight by Lutron PIR Sensor Assembly; for 16 to 30 ft (4.9 to 9 m) mounting height
Limelight by Lutron PIR Sensor Assembly; for 31 to 40 ft (9.5 to 12 m) mounting height
1.24 (31.4)
1.12 (28.5)
0.57 (14.5)
Top View
1.12 (28.5)
0.57 (14.5)
Tallest
Tallest component
component
approx. 0.8 (20.3)
approx. 0.16 (4)
0.19 (4.8)
0.57 (14.5)
1.12 (28.5)
Ø2.751
(Ø69.9)
Preferred mounting hole
1
Integration Guide
2.69 (68.3)
Solder mask is not relieved around
Bottom View
holes. If using metal fasteners,
plastic washers/spacers must
be used.
0.829 (21)
Preferred mounting hole
Customer Assistance: 1.844.LUTRON1
P/N 041664 Rev. D
01/2019
(1.844.588.7661)
Advertisement
Table of Contents
Related Manuals for Lutron Electronics LL-INTMOUNT
Summary of Contents for Lutron Electronics LL-INTMOUNT
- Page 1 Preferred mounting hole The LL-INTMOUNT module has multiple holes (diameter = 0.11 in [2.75 mm]) for mounting to a luminaire. The LL-INTMOUNT should be mounted using a minimum of two of the holes to ensure that the PCB does not excessively vibrate.
- Page 2 5-Pin Connector (J1) The LL-INTMOUNT has a 5-pin connector for connection to the AC power and the luminaire. During manufacturing, solid core or tinned wires can be pressed into the connector slots. For stranded wires, press down on the button next to each connector slot to allow wire entry. Releasing the button will cause the connector to grip the wire.
-
Page 3: Power Connections
The Load output connection can support an electronic ballast load of up to 1000 W at 277 V~ and 600 W at 120 V~. Multiple loads can be driven by the same LL-INTMOUNT as long as the total wattage does not exceed the maximum wattage for the given drive voltage. -
Page 4: Surge Suppression
The LL-INTMOUNT is designed and rated to operate in an ambient temperature of -40 – 176 ˚F (-40 – 80 ˚C). Ambient air temperature is measured at least 1 in (25.5 mm) away from the LL-INTMOUNT. The LL-INTMOUNT is not waterproof and should not be mounted in a location where it will receive direct contact with water. - Page 5 (Ø29.94) Ø0.06 (Ø1.69) 1. Connect LL-PIR to LL-INTMOUNT with cable assembly shown below (either end can connect to either LL-PIR or LL-INTMOUNT). 2. Recommended plastic PIR lens assembly should be tightened to 4 in-lbs (0.45 N•m) to properly engage the internal seal.
-
Page 6: Manufacturing Test
The LL-INTMOUNT has a red LED on the bottom side of the PCB (opposite side from the connector). When the LL-INTMOUNT is powered this LED should come on. The state of the LED will tell you information about the state of the LL-INTMOUNT. - Page 7 Limelight by Lutron OEM Integration Guide )Lutron and Lutron are trademarks of Lutron Electronics Co., Inc., registered in the U.S. and other countries. Limelight is a trademark of TwistHDM, LLC. Lutron Contact Numbers WORLD HEADQUARTERS EUROPEAN HEADQUARTERS ASIAN HEADQUARTERS United Kingdom Singapore Lutron GL Ltd.
-
Page 8: Numéros De Modèle
Trou de montage préférentiel Le module LL-INTMOUNT présente plusieurs trous (diamètre = 2,75 mm [0,11 po] permettant de le monter sur un luminaire. Le LL-INTMOUNT doit être monté en utilisant au moins deux des trous pour s’assurer que le circuit imprimé ne vibre pas excessivement. - Page 9 Intégration électrique Connecteur à 5 broches (J1) Le LL-INTMOUNT dispose d’un connecteur à 5 broches permettant de le connecter à l’alimentation électrique et au luminaire. Lors de sa fabrication, des fils massifs ou des fils étamés peuvent être pressés dans les fentes du connecteur.
- Page 10 3 weeks, starting from when the sample is received by Lutron. For best RF performance of the LL-INTMOUNT, the antenna should be kept 1.25 in (31.75 mm) from other metal components and should not be concealed in a metal box. If either of these are violated a sample fixture will be requested.
- Page 11 (1 po) du LL-INTMOUNT. Le LL-INTMOUNT n’est pas étanche et ne doit pas être monté dans un endroit où il sera en contact direct avec de l’eau. Toutefois, il possède un revêtement enrobant et peut résister à des conditions humides ou moites.
- Page 12 Guide d’intégration des équipementiers d’origine de Limelight par Lutron 4. Intégration du LL-PIR-(L/M/H) Le LL-INTMOUNT peut être connecté à détecteur infrarouge passif externe Limelight par Lutron (LL-PIR-[L/M/H]) par le biais du connecteur à 4 broches représenté ci-dessous. 38,09 (1,5) Connecteur de détecteur...
-
Page 13: Garantie
Le fil conducteur (noir) n’est pas connecté à la borne de ligne du LL-INTMOUNT. c. Le fil neutre (blanc) n’est pas connecté au neutre du luminaire et à la borne neutre du LL-INTMOUNT. 3. Le luminaire s’allume et reste au seuil haut : Les fils de gradation ne sont pas connectés ou sont inversés. - Page 14 Guide d’intégration des équipementiers d’origine de Limelight par Lutron )Lutron et Lutron sont des marques commerciales de Lutron Electronics Co., Inc. enregistrées aux États-Unis et dans d’autres pays. Limelight est une marque commerciale de TwistHDM, LLC. Numéros de téléphone de Lutron SIÈGE MONDIAL...