Keysight InfiniiVision M9241A Scpi Programmer's Manual page 1500

Index
trigger edge source, Edge Then Edge
trigger, 1075
trigger event bit, 238
Trigger Event Register (TER), 1309
trigger event, NFC trigger, 1101
TRIGger GLITch commands, 1087
trigger holdoff, 1059
trigger idle, UART, 917
TRIGger IIC commands, 792
trigger level auto set up, 1063
trigger level constants, 282
trigger level voltage, 1083
trigger level, high, 1064
trigger level, low, 1065
TRIGger LIN commands, 802
trigger line used in multi-module
triggering, 1123
TRIGger M1553 commands, 821
TRIGger NFC commands, 1095
trigger occurred, 196
TRIGger OR commands, 1106
TRIGger PATTern commands, 1108
trigger pattern qualifier, 1114
TRIGger PXI commands, 1116
trigger qualifier, UART, 918
trigger reset conditions, 190,
TRIGger RUNT commands, 1124
TRIGger SHOLd commands, 1129
trigger status bit, 238
trigger sweep mode, 1053
TRIGger TV commands, 1135,
trigger type, ARINC 429, 743,
trigger type, UART, 919
TRIGger UART commands, 900
TRIGger ZONE commands, 1150
trigger, ARINC 429 source, 736
trigger, CAN, 762
trigger, CAN FD sample point,
trigger, CAN pattern data length,
trigger, CAN pattern ID mode,
trigger, CAN sample point, 757
trigger, CAN signal baudrate, 758
trigger, CAN signal definition,
trigger, CAN source, 761
trigger, duration greater than,
trigger, duration less than, 1113
trigger, duration range, 1115
trigger, edge coupling, 1082
trigger, edge level, 1083
trigger, edge reject, 1084
trigger, edge slope, 1085
trigger, edge source, 1086
trigger, force a, 1057
trigger, glitch greater than, 1088
trigger, glitch less than, 1089
trigger, glitch level, 1090
trigger, glitch polarity, 1091
trigger, glitch qualifier, 1092
trigger, glitch range, 1093
trigger, glitch source, 1094
trigger, high frequency reject filter,
trigger, holdoff, 1059
1500
trigger, IIC clock source,
trigger, IIC data source,
trigger, IIC pattern address,
trigger, IIC pattern data,
trigger, IIC pattern data 2,
trigger, IIC qualifier,
trigger, IIC signal baudrate,
trigger, IIC type,
trigger, LIN,
trigger, LIN pattern data,
trigger, LIN pattern data length,
trigger, LIN pattern format,
trigger, LIN sample point,
trigger, LIN signal definition,
trigger, LIN source,
trigger, mode,
trigger, noise reject filter,
trigger, Nth edge burst source,
trigger, Nth edge in burst slope,
trigger, Nth edge of burst count,
trigger, Nth edge of Edge Then Edge
trigger,
trigger, sweep,
trigger, TV line,
trigger, TV mode, 1142,
1024 trigger, TV polarity,
trigger, TV source,
trigger, TV standard,
trigger, UART base,
trigger, UART baudrate,
1140 trigger, UART bit order,
966 trigger, UART parity,
trigger, UART polarity,
trigger, UART Rx source,
trigger, UART Tx source,
trigger, UART width,
truncation rules,
755 TST (Self Test),
768 tstart, 1273
771 tstop, 1274
turn function on or off,
turn off channel,
759 turn off channel labels,
turn off digital pod,
1112 turn off math function,
turn off time, 532, 629,
turn on channel labels,
turn on time, 533, 629,
turn on/turn off analysis thresholds,
turn on/turn off time analysis, 626, 627,
628, 629
turning channel display on and off,
turning off/on function calculation,
turning vectors on or off,
TV mode, 1142,
TV trigger commands, 1135,
TV trigger line number setting,
TV trigger mode,
TV trigger polarity,
TV trigger standard setting,
1058 TV triggering,
tvmode, 1292
Keysight InfiniiVision M9241/42/43A PXIe Oscilloscopes SCPI Programmer's Guide
794
795
796
797
798
799
807
800
811
814
816
817
806
1289
808
1066
1067
1080
1079
1077
1073
1068
1141
1292
1143
1144
1145
914
903
904
910
911
912
913
920
1356
198
1266
210
326
210
210
630
326
630
630
277
369
1259
1292
1140
1141
1144
1143
1145
1054
Tx data, UART, 1183
Tx frame count (UART), 908
Tx source, 913
type of power being converted, efficiency
measurement, 605
U
UART base, 914
UART baud rate, 903
UART bit order, 904
UART frame counters, reset, 906
UART parity, 910
UART polarity, 911
UART Rx source, 912
UART SEARch commands, 1006
UART serial search, data, 1007
UART serial search, data qualifier,
UART serial search, mode, 1008
UART trigger burst, 915
UART trigger commands, 900
UART trigger data, 916
UART trigger idle, 917
UART trigger qualifier, 918
UART trigger type, 919
UART Tx data, 1183
UART Tx source, 913
UART width, 920
UART/RS-232 triggering, 722
units (vertical) for FFT, 382
units per division, 292, 293, 343,
units per division (vertical) for
function, 292, 396
units, automask, 551
units, X cursor, 423, 424
units, Y cursor, 430, 431
unsigned data, 1163
unsigned mode, 1185
update rate, waveform, 1021
upper threshold, 483
upper threshold voltage for
measurement, 1276
uppercase characters in commands,
URQ (User Request) status bit, 179,
USB PD trigger mode, 923
USB PD trigger, control message type,
USB PD trigger, data message type, 928,
929
USB PD trigger, header content trigger
qualifier, 932
USB PD trigger, header type, 924
USB PD trigger, user-defined header
value, 931
USB PD triggering, 722
USB PD waveform source, 922
USBPd serial bus commands,
user defined channel labels, 280
user event conditions occurred,
User's Guide, 6
user-defined baud rate, ARINC 429,
1009
1047
1355
181
926
921
196
730