Advertisement
Available languages
Available languages
English
General Precautions
Opening the packaging
• R ead the instructions carefully before starting installation
and proceed as specified by the manufacturer;
General prescriptions for installation
• I nstallation, programming, commissioning and maintenance
of the product must only be performed by qualified techni-
cians who have been properly trained in compliance with
current standards, including health and safety regulations;
• T he installer must make sure that the information for the user,
where applicable, is present and is delivered;
Maintenance
• B efore performing any cleaning or maintenance operation,
disconnect the power supply to the device; if the equipment
is powered by mains voltage disconnect the power supply,
opening the switch located upstream of it;
• T he equipment must be used only for the purpose for which
it was explicitly designed.
• T he manufacturer declines all liability for any damage as a
result of improper, incorrect or unreasonable use.
VAS/101
Installation
B
The power supply unit must ALWAYS be installed horizontally.
The device can be installed on DIN rails (EN 50022) a, on a
suitable switchboard, or on the wall using the terminal board
covers . To dismantle it, proceed as shown in figure c.
NOTE. Ensure there is correct ventilation if the power
supply unit is installed in a metal case.
Technical data
Type
VAS/101
Power supply
230 VAC 50÷60 Hz
I
Input current
Dissipated power (W max)
10
Nominal power supply
18 VDC 1 A-0,5 A 1'/3'
Dimensions (DIN)
4
Storage temperature (°C)
-25 ÷ + 70
Operating temperature (°C)
0 ÷ +35
IP Degree
30
Functions
C
Terminal boards a
~
Mains
~
+
Power supply 18 VDC (*)
–
(*) The appliance is electronically protected against overlo-
ads and short circuits.
LC-01 LVC-01
Wall mounting
Using the Allen screwdriver remove the cover
wall plugs provided fix the entry panel at the desired height
E
respecting the positioning of the lens of the surveillance
camera
.
G
Push through pipe
E
, take off the terminal board cover
E
c and make the connections. Put back on the terminal
board covers and assemble the front cover.
4
Recessed installation
Wall in the recessed box
the positioning of the lens of the surveillance camera
Push the pipe with the system conductors through one of the
breaking points (
When using the recessed box any possible deformations can be
avoided by using the spacer provided (
Using the Allen screwdriver remove the cover
the frame surround in the recessed box
nection cables through hole
H
. Take off the terminal board cover
connections. Once the connections have been made, put back
on the terminal board cover and assemble the front cover.
Accessories
a DPS single button;
LTP Wall roof;
c Recessed box LSI;
d Recessed frame LCI;
Assembly and removal of buttons modules
Insert the button module
down orientation
Remove the small piece of glass and write the names
attention to the direction of insertion of the glass panel
Connection examples
Technical data
Type
Power supply (VDC)
Absorption (mA)
Consumption in stand-by mode
(mA)
Storage temperature (°C)
max
=200 mA
Operating temperature (°C)
AC
AC
IP Degree
Size of name cards (mm)
Camera
Standard video
Resolution (pixel)
Minimum lighting (LUX)
Functions
Termina block a
BOUT Riser
–
Power supply
+
16-18 VDC
– Ground
Door lock release button (NA)
– Solenoid lock
12 V 1 A max
Adjustments c
loudspeaker audio
E
a. With the
microphone audio
solenoid lock 1-10 s. (default 1 s)
Programming
The entry panel is supplied already configured through a call
put through to any receiver that has NEVER been programmed.
It is possible, however, to add buttons or receivers as explained
in the entry panel's programming manual.
at the desired height, respecting
F
point A).
F
point B).
F
E
H
a, push the con-
E
and secure the entry panel
E
c and make the
I
paying attention to the up to
L
L
a.
O
LC/01-LVC/01
16-18
320
130
-25 ÷ + 70 °C
0 ÷ +35
54
5 3 x 1 3 x 0 , 3 o r
53x33x0,3
LVC/01
PAL/NTSC
680x512
1
P
DISPOSAL
Do not litter the environment with packing material: make
sure it is disposed of according to the regulations in force in
.
G
the country where the product is used.
When the equipment reaches the end of its life cycle, take
measures to ensure it is not discarded in the environment.
The equipment must be disposed of in compliance with the
regulations in force, recycling its component parts wherever
a. Position
possible.
Components that qualify as recyclable waste feature the
relevant symbol and the material's abbreviation.
L M N
paying
M
a.
N
Advertisement
