Download Print this page

Philips 4000SX/00 User Manual page 10

Professional solarium

Advertisement

Available languages
  • EN

Available languages

  • ENGLISH, page 1
ENGLISH
10
Setting the body cooler (C20)
The default setting is 4. Setting options are 0 to 4.
Service menus
Menus C08, C09, C10, C11, C12 are service menus that can only be adjusted by staff of an authorised Philips service centre.
Leaving owner's menus
Return to menu C00 and press the I button to leave the menus.
Cleaning
Always unplug the appliance and let it cool down before you start cleaning it.
Never use alcohol, methylated spirits, petrol and acetone or cleaners containing these substances to clean the acrylic sheets, as this may
cause irreparable damage.
Clean the outside of the appliance with a damp cloth.
Do not let any water run into the appliance.
Clean the appliance with a damp cloth after every 250 operating hours to limit discolouration of the parts of the appliance exposed to
UV.
Replacement
The light emitted by the tanning lamps will become less bright in time.When this happens, you will notice a decrease in the tanning capacity of
the appliance.You can solve this problem by setting a slightly longer tanning time or by replacing the tanning lamps.
To replace the tanning lamps and/or starters, proceed as follows.
1
Remove the mains plug from the wall socket.
2
Undo the quarter-turn screws in the fastening strips at both ends of the acrylic sheet (fig. 22).
3
Snap loose the strips along both sides of the acrylic sheet by placing your fingers under the strip and pulling it up at various places (fig.
23).
4
Remove the acrylic sheet.
Always remove the mains plug from the wall socket before removing the acrylic sheet.
5
Remove the lamp end covers (fig. 24).
6
To remove the lamps, turn them to the left or to the right so that you can lift them out of their holders.
7
The starters can be removed by turning them to the left.
8
Insert new lamps and/or starters.
Always replace the tanning lamps with Philips Cleo Performance SR tube lamps. Put 100W lamps in the couch and 80W lamps in the
canopy.
B
NB:The canopy of HB600/3200SX contains 16 80W tube lamps and two 100W tube lamps.
NB:The canopy of HB604/6000SX contains 23 140 W Philips Cleo Professional R tube lamps.
B
NB:The couch of HB604/6000SX contains 17 100W Philips Cleo Professional R tube lamps.
B
Always replace starters with Philips S12 starters or Cleo Sunstarters.
9
Slide the lamp end covers back into the end covers on either side.
10
Put the acrylic sheet back and fasten it by snapping home the strips on either side.
11
Tighten the quarter-turn screws in the fastening strips at both ends of the acrylic sheet.
The lamps and/or starters of the couch and canopy are replaced in the same way.
Replacing an HPA lamp
1
Remove the acrylic sheet.
Always remove the mains plug from the wall socket before removing the acrylic sheet.
2
Remove the lamp end cover at the facial tanner side of the canopy.
3
Loosen the screws that hold the HPA lamp unit in place.
4
Tilt the HPA lamp unit out of the canopy.
5
Turn the black retaining screws and remove them.
6
Slide the filter glass out of the lamp unit.
7
Remove the HPA lamp and put in a new one.
Always replace the HPA lamps with HP 400 SH lamps.
8
Slide the filter glass back into the lamp unit and fasten it with the black retaining screws.
9
Push the HPA lamp unit back into the canopy and fasten it with the screws.
10
Reassemble the lamp end cover and the acrylic sheet.
To replace the starter of the HPA lamp, proceed in the same way.
Always replace starters with Philips CD Z 400M starters.

Advertisement

loading