Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for LineEye LE590-TAP
Summary of Contents for LineEye LE590-TAP
- Page 1 LE590-TAP User’s Manual <2nd>...
-
Page 2: Table Of Contents
Table of Contents 1. LE590-TAP Overview ................3 1.1. Hardware Installation ......................3 1.2. StartingLE590-TAP ......................3 1.3. LE590-TAP Main Window Overview ..................5 2. LE590-TAP Functions ................6 2.1. Menu Bar ..........................6 2.1.1. File ..........................6 2.1.2. Config ..........................7 2.1.2.1. Run Mode ........................7 2.1.2.2.Port Configuration.......................7... -
Page 3: Le590-Tap Overview
USB port for monitoring and analyzing. The user can specify conditions to filter the packets wanted with LE590-TAP application software. It reduces USB port’s network traffic and also cuts down PC resource consumption while dealing with large quantity of packets. - Page 4 When your PC cannot detect your LE-590TX, a window as shown above will pop up asking if you want to start the LE590-TAP in Demo mode or not, also a third option will pop up asking if you want to re-install WinPcap for successfully run the LE590-TAP.
-
Page 5: Le590-Tap Main Window Overview
1.3. LE590-TAP Main Window Overview LE590-TAP Functions Overview The Menu Bar allows you to make settings about task criteria, view Counter Menu Bar window, load/save settings you’ve made, and change language displayed. The Tool Bar contains buttons that allow you to reconnect your PC to Tool Bar LE-590TX, make task/port configurations, view Counter, USC A/B and Charts. -
Page 6: Le590-Tap Functions
Path to… button to save the setting, or Cancel button to close the window. A prompt pop-up window will ask if you are sure to exit LE590-TAP. Click YES to exit Exit LE590-TAP, or click NO to cancel. Website: www.lineeye.com... -
Page 7: Config
Seldom option. After finishing the settings, please click Apply button to save the configuration, or click Cancel to close window without saving. *Note: Changing settings in Port Configuration window might cause Link Status changes and packet loss. Website: www.lineeye.com... -
Page 8: 3.Frame Gap For Usb Transferring
Seldom option. After finishing the settings, please click Apply button to save the configuration, or click Cancel to close window without saving. *Note: Changing settings in Port Configuration window might cause Link Status changes and packet loss. Website: www.lineeye.com... -
Page 9: Statistics
Update button is shown as the figure on the left, than the counter operation is paused. If the Update button is shown as the figure on the left, the counter operation is started. Hide the data of zero. Show all data. Click the Clear All button to clear the counter data. Website: www.lineeye.com... -
Page 10: Alarm Report
Alarm Report window, please refer to the 2.2.5. Port AB, Alarm. The Save button allows you to save the Alarm Report data on a path folder. If you click the Clear All button, you will clear all the data gathered on this window. Website: www.lineeye.com... -
Page 11: Control
20000 packets are saved as one file, and the latest 20000 packets are displayed in the screen. *Note: Data is saved as a pcap format. To check the recorded data, you need to have a software such as Wireshark. Website: www.lineeye.com... -
Page 12: Auto Save
Click this option to auto save Alarm Report to the Report folder below your Alarm Report LE590-TAP folder in each 60 min. Auto Save Setting 2.1.5. Languages Languages English/Simplified LE590-TAP has 3 different languages for its UI available. You can set the UI Chinese/Japanese language to English, Simplified Chinese or Japanese. Website: www.lineeye.com... -
Page 13: Help
OK: Click this button to exit the “System Requirements” pop-up window. LINEEYE Web Open your default web browser and access LINEEYE Website (www.lineeye.com) Clicking this option will pop up a LOG window showing the settings that you made on LE590-TAP program so far. -
Page 14: Tool Bar
“System Connection Status” will be shown as “Connected” 2.2.2. Counter Counter If you click the Counter button, the Counter Window will pop up showing the status of the packets. For more information, please refer to the 2.1.3.1. Counter Window. Website: www.lineeye.com... -
Page 15: Usc A & Usc B
Note: The Operation mode is not available yet. The left figure shows the Rule (Stream Counter Mode) available when you scroll down the field. After applying your settings made on the Setting window, the changes will be shown on the Port Universal Streams Counter window. Website: www.lineeye.com... -
Page 16: Chart
Start/End Time scroll field from E will be available. The function of Start/End Time allows you to check the status of the packets of the saved chart in different times. The Update button allows you to pause or start the counter operation. Website: www.lineeye.com... - Page 17 A to view the pie chart in B field. The pie chart shows the percentage of each captured packet size during the operation of the LE590-TAP. You can set the Rate of packets to be analyzed in Mbps in C field. If you set in Auto mode, the Rate will be set under a default setting, if you set in User Define mode, than a Minimum and a Maximum rate range will be available to modify.
- Page 18 You can open a saved chart by clicking the button. When opening a saved chart, the Start/End Time scroll field from D will be available. The function of Start/End Time allows you to check the status of the packets of the saved chart in different times. Website: www.lineeye.com...
-
Page 19: Port Ab
You can also set MDIX mode here, and click the Set button to save settings made for MDIX mode: If you set Auto MDIX mode, the LE590-TAP will auto sense the direction of Tx/Rx for signal connection between LE-590TX with NIC/Switch side. - Page 20 Port AB_Capture Criteria In the Protocol interface, If you click the Capture all packets function, you will enable the LE590-TAP to capture all packets criteria. If you close the Capture all packets function, than the criteria from MAC, Network and Protocol will be available to choose.
- Page 21 DA / SA (destination / source MAC address) and recalculated CRC. If you choose the Single-End Mode on Loopback interface, the selected ports are idle that all transmitting and/or receiving data streams via these ports are disabled. Website: www.lineeye.com...
- Page 22 Port A and Port B at same time with the same packets capture criteria. If you want to configure Port A and Port B at different packets capture criteria, please choose the to configure separately with different packets capture criteria. Website: www.lineeye.com...
-
Page 23: System Info/Configuration List
2.3. System Info/Configuration List The System Info/Configuration List allows you to view system information and making port configurations. Website: www.lineeye.com... -
Page 24: System Information
2.3.1. System Information By clicking the System Information on the System Info/Configuration List, the System Information screen will be shown on the Main Display Screen located on the right side of LE590-TAP’ main window. Website: www.lineeye.com... -
Page 25: Port A & Port B
Configuration screen will be shown on the Main Display Screen located on the right side of LE590-TAP’ main window, allowing you to make settings for LE-590TX ports. Those settings include the Media Type, Capture Criteria, Loopback and Alarm related to For more detail description about Port A &... -
Page 26: Port A / Port B
Configuration screen will be shown on the Main Display Screen located on the right side of LE590-TAP’ main window, allowing you to make settings for LE-590TX ports. Those settings include the Media Type, Capture Criteria, Loopback and Alarm related to . -
Page 27: Capture Buffer Mode And Capture Forward Mode
* While capturing in the port A or port B, do not capture in the port A & port B. * While capturing in the port A & port B, do not capture in the port A or port B. Website: www.lineeye.com... -
Page 28: Report: Usc A/B
Not operating Operating 2.4.2. For Layer 1/Layer 2 Loopback mode and Single-End mode The Control Buttons allow you to start/stop tasks, and the Operating Status Icon indicates if there’s a task running. Control Buttons Start task Stop task Website: www.lineeye.com... - Page 29 Operating Status Icon Not operating Operating Website: www.lineeye.com...
- Page 30 4F., Marufuku Bldg., 39-1, Karahashi Nishihiragaki-cho, Minami-ku, Kyoto, 601-8468, Japan Phone: 81-75-693-0161 Fax: 81-75-693-0163 URL: https://www.lineeye.com M-29590TAPE/LE...
Need help?
Do you have a question about the LE590-TAP and is the answer not in the manual?
Questions and answers