Summary of Contents for Christie Velvet Apex LED009-AL
Page 1
Installation and Setup Guide 020-102213-04 Velvet LED Display System Apex Series...
Page 2
The warranty does not apply to any product where the serial number has been removed or obliterated. The warranty also does not apply to any product sold by a reseller to an end user outside of the country where the reseller is located unless (i) Christie has an office in the country where the end user is located or (ii) the required international warranty fee has been paid.
Product overview Christie Velvet LED Display System tiles are modular, high-quality image display units that can be configured to achieve an HD display, depending on the pixel pitch of the tile being installed. Each Christie E500 LED Display Controller can support a maximum number of tiles, which varies depending on the pixel pitch of the tiles in the array.
Warning! If not avoided, the following could result in death or serious injury. • After the replacement of the power supply, hi-pot and ground/earth bond tests must be performed. Only Christie qualified technicians who are familiar with the necessary precautions can perform these tests. •...
Remote Power Supply Rack Shelf module, you must purchase a power cord of an adequate length. Christie recommends one of the pre-terminated power cables offered as Christie accessories, or that you create a custom cable using the Christie Main Power Cable Spool (P/N 154-122106-XX), Connector Kit (P/N 154-125109-XX), and Molex Crimping Tool (P/N 154-124108-XX).
Product overview Related documentation Additional information on the Christie Velvet LED Display System is available in the following documents. • Christie Velvet LED Display Control System Apex Series Product Safety Guide (P/N: 020-102212-XX) • Christie E500 LED Display Control System Software User Manual (P/N: 020-102222-xx) •...
When installing the cables from tile to tile, installing a primary data cable (blue) and a backup data cable (purple) creates redundancy. Each Christie E500 LED Display Controller can support a maximum number of tiles, which varies depending on the pixel pitch of the tiles in the array. The configuration to achieve an HD display differs by the pixel pitch of the tile, as outlined in the table below.
2.5 mm 8 x 8 64 tiles Christie E500 LED Display Controller interface and ports Learn about the interface and physical ports on the Christie E500 LED Display Controller. Front Power button USB interface for communication with a computer Input selector...
Warning! If not avoided, the following could result in death or serious injury. • External support for a display wall must be designed and implemented by a Christie qualified installer and must comply with local area regulations and safety standards.
Warning! If not avoided, the following could result in death or serious injury. • External support for a display wall must be designed and implemented by a Christie qualified installer and must comply with local area regulations and safety standards.
Page 19
7. Daisy chain the primary and backup data cables from one tile to the next, ensuring the cables are not crossed. OUT1 must be connected to IN1, and OUT2 must be connected to IN2. You do not need to make a complete loop between the Christie E500 LED Display Controller and the tiles.
Connecting the LED tile power cables to the Remote Power Supply Rack Shelf To power the Christie Velvet LED Display System tiles, connect the cables between the tiles and the Remote Power Supply Rack Shelf. 1. Connect the main power cable to the Remote Power Supply Rack Shelf.
Connecting the LED tile power cables to the Remote Power Supply Rack Shelf To power the Christie Velvet LED Display System tiles, connect the cables between the tiles and the Remote Power Supply Rack Shelf. 1. Connect the main power cable to the Remote Power Supply Rack Shelf.
Installation and setup 1. Connect the data cable from the first tile in the array to the Christie E500 LED Display Controller. 2. Connect the HDMI or DVI output from the video source (computer or media player) to the appropriate input port on the Christie E500 LED Display Controller.
Testing the communication between the controller and tiles Verify that the array is connected to and recognized by the Christie E500 LED Display Controller. 1. Connect the USB cable between the controller and the computer running the Christie E500 LED Display Controller software.
Installation and setup Reviewing the tile configuration Review the tile configuration reported in the Christie E500 LED Display Controller software. 1. In the Christie E500 LED Display Controller software, click Screen Configuration. 2. Select Configure Screen and click Next. 3. Switch to the Screen Connection tab.
Maintaining the LED panels Learn the information and procedures for performing maintenance on the Christie Velvet LED Display System. Cleaning the LED panels Learn how to clean the Christie Velvet LED Display System panel. Notice. If not avoided, the following could result in property damage.
Typical: 74 W per panel, Max: 220 W per panel Typical: 47 W per panel, Max: 140 W per panel LED025-AL Input rating for the Christie E500 LED Display Controller Input rating 100-250 V~, 50-60 Hz, 1.5A, 75 watts Power ratings for the Remote Power Supply Rack Shelf...
Specifications The number of displays that can be powered by a single Remote Power Supply Rack Shelf depends on the voltage range of the input and the number of rectifiers. Please consult your local Christie representative for further details. Max power...
Page 33
Italy ph: 714-236-8610 ph: +39 (0) 2 9902 1161 Canada – Kitchener ph: 519-744-8005 Corporate offi ces Worldwide offi ces Christie Digital Systems USA, Inc. Australia Germany Republic of South Africa United Kingdom Cypress ph: +61 (0) 7 3624 4888...