Table of Contents
Advertisement
Quick Links
Installation instructions
Install the washer on a solid and level floor surface ensuring it has at least 20 mm clearance on each side. The washer
must not be installed on any textured floor coverings (eg carpets, rugs).
Product and minimum clearance dimensions
https://producthelp.fisherpaykel.com/au/Wash/Top_Loaders/CleanSmart/WL8060P1/User_Guide_WL8060P1/03_Installation_...
Updated: Fri, 14 Feb 2020 17:08:14 GMT
Powered by
1
Advertisement
Table of Contents
Related Manuals for Fisher & Paykel CleanSmart WL8060P
Summary of Contents for Fisher & Paykel CleanSmart WL8060P
-
Page 1: Installation Instructions
Installation instructions Install the washer on a solid and level floor surface ensuring it has at least 20 mm clearance on each side. The washer must not be installed on any textured floor coverings (eg carpets, rugs). Product and minimum clearance dimensions https://producthelp.fisherpaykel.com/au/Wash/Top_Loaders/CleanSmart/WL8060P1/User_Guide_WL8060P1/03_Installation_…... -
Page 2: Product Dimensions
Product Dimensions Property (mm) WL8060P Overall height of product* (to highest point on console) 1045 – 1075 Overall width of product Overall depth of product Height of product to top of lid* (closed) 950 – 980 Height of lid open* (measured from bottom of product) 1350 –... -
Page 3: Maximum Capacity
Maximum Capacity Property (kg) WL8060P Maximum Capacity * Includes adjustable mounted feet and the range of movement. # Applies either side. Unpacking To ensure the best performance from your new washer please follow the instructions below. Removing the packaging 1. Remove the outer packaging. 2. -
Page 4: Drain Hose
Please ensure that the base packer has been removed BEFORE OPERATING your washer. Location Install the washer on a solid and level floor surface ensuring it has at least 20 mm clearance on each side. The washer must not be installed on any textured floor coverings (eg carpets, rugs). -
Page 5: Electrical Connection
3. Place the drain hose in the tub or standpipe. Do not fit the hose to a drain spigot. Drainage must not be airtight in order to prevent siphoning. Electrical connection • This appliance must be supplied with a 220 – 240 V, 50 Hz, sinusoidal, 10 A electrical supply. •... -
Page 6: Inlet Hoses
Inlet hoses Failure to adhere to the following instructions may result in a flood and damage to property: • New hose sets provided with the washer shall be used to connect the washer to the water supply. • Old hose sets should not be used. - Page 7 Your washer does not have an internal heater to heat water. Levelling instructions It is IMPORTANT to level the washer to ensure good spin performance. A spirit level is provided with your washer. Use this to level your washer, always placing it on a clean, flat surface. The washer is level when the bubble sits in the centre, within the two lines.
-
Page 8: Completing Your Installation
washer is level in all areas. Repeat step 4 if necessary. Check the washer does not rock from side to side, front to back, or corner to corner. • Keep your spirit level for the next time you move or reposition your washer. -
Page 9: Installation Test Cycle
Installation test cycle Your washer must be correctly installed before use. Check the installation and operation of the washer using the following procedure: 1. Touch ‘Power’ to activate your washer. 2. Touch both the and ‘Options’ buttons at the same time, and hold for three seconds. 3. - Page 10 Accessories and Spare Parts Extension Power If the power cord of your clothes washer is damaged it must be replaced by a Fisher & Paykel Cord Authorised Repairer in order to avoid a hazard, as it is not a standard power cord. https://producthelp.fisherpaykel.com/au/Wash/Top_Loaders/CleanSmart/WL8060P1/User_Guide_WL8060P1/03_Installation_…...