Related Manuals for Fisher & Paykel WL8058G1
Summary of Contents for Fisher & Paykel WL8058G1
- Page 1 TOP LOAD WASHING MACHINE WL8058G1, WL9058G1, WL1064G1, WL1064P1, WL1264P1 models INSTALLATION GUIDE NZ AU...
- Page 3 SAFETY AND WARNINGS WARNING! MODEL CODE MAX CAPACITY* (KG) WL8058G1 Electrical Shock Hazard WL9058G1 Failure to follow this advice may result in electrical shock or death. WL1064G1, WL1064P1 • If you are using an extension cord or WL1264P1 a portable electrical outlet device (eg *Capacity refers to the maximum dry weight of items the washer can wash at any one time.
-
Page 4: Supplied Parts
SUPPLIED PARTS SPARE PARTS Keep all packing materials until the unit has been inspected. SPARE PARTS* PART NO. Inspect the product to ensure there is no shipping damage. If any damage is detected contact the dealer or retailer you bought the product from to report the damage. Hose(s) inlet long (1.5 m) 422680P Fisher &... -
Page 5: Product Dimensions
PRODUCT DIMENSIONS WL8058G1 & WL9058G1 models PRODUCT DIMENSIONS A Overall height of product (to 995 – 975 highest point on lid) B Overall width C Overall depth* D Height of product lid closed 1020 - 1040 (to highest point of console) - Page 6 PRODUCT DIMENSIONS WL1064G1, WL1064P1 & WL1264P1 models PRODUCT DIMENSIONS A Overall height of product (to 1025 – 1045 highest point on lid) B Overall width C Overall depth* D Height of product lid closed (to 1085 - 1105 highest point on console) E Height of product lid open 1500 - 1520 * Exact height is dependent on foot adjustment...
- Page 7 CAVITY & CLEARANCE DIMENSIONS ISOMETRIC FRONT PROFILE CAVITY DIMENSIONS 580 MODELS 640 MODELS CLEARANCE DIMENSIONS A Minimum clearance to either side, wall or adjacent product A Minimum cavity width B Minimum gap clearance at the rear of the product B Minimum cavity depth Actual dimensions may vary by ±...
- Page 8 ELECTRICAL & PLUMBING CONNECTION CONNECTION LOCATIONS / LENGTHS DRAINAGE HEIGHTS Water Hoses 1500mm 900mm min - 1200mm max* Power Cord 1500mm Drain Hose 1500 or 1600mm (model dependant) * Recommended standpipe height is 1000mm 580 models only SPECIFICATIONS ELECTRICAL Water Hoses Supply 220 – 240 V, 50 Hz Service...
-
Page 9: Water Supply
UNPACKING WATER SUPPLY Unpacking Water supply requirements To ensure the best performance from your new washer please follow the instructions below. If you have an uncontrolled water heating source (eg a wet back or solar heating system) you should fit a tempering valve. This will ensure the hot water temperature remains within safe limits. -
Page 10: Levelling The Washer
DRAINING LEVELLING THE WASHER Levelling instructions In multi-storey apartments or any upper floor, the washer should be installed on a floor equipped with a drain. Draining must comply with local by-laws. It is IMPORTANT to level the washer to ensure good spin performance. Your washer is equipped with adjustable feet at the front. -
Page 11: Complete Installation
COMPLETE INSTALLATION INSTALLER CHECKLIST Completing the installation TO BE COMPLETED BY THE INSTALLER Turn on the water and check all hose connections for leaks. Ensure there are no kinks in the hoses. Check the hose connections for leaks again after 24 hours. …... - Page 12 FISHERPAYKEL.COM © Fisher & Paykel Appliances 2023. All rights reserved. The models shown in this guide may not be available in all markets and are subject to change at any time. The product specifications in this guide apply to the specific products and models described at the date of issue.
Need help?
Do you have a question about the WL8058G1 and is the answer not in the manual?
Questions and answers