1. Manuals
  2. Brands
  3. Falcon Manuals
  4. UPS
  5. SG800-1, SG800-2 SG1K-1T, SG1K-2T SG2K-1T
  6. Battery replacement manual

Falcon SG1K-1T Battery Replacement Manual

Hide thumbs Also See for SG1K-1T:
1
2
3
4
5
6
7
8

Advertisement

Table of Contents

BATTERY
REPLACEMENT
GUIDE
Uninterruptible Power Supply Models:
SG1K-1T, SG1K-2T
FALCONElectric Inc., 5116 Azusa Canyon Rd., Irwindale, California 91706, (626) 962-7770, Fax 626-962-7720, Email: sales@falconups.com
®
2004 Falcon
®
Electric Inc. All rights reserved.
All other brand names and trademarks are the property of their respective owners.
The information stated in this document is subject to change without notice. 2004-02-02
Falcon
®
, Falcon® Electric and UPS Plus logos are registered trademarks of Falcon Electric Inc

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SG1K-1T and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Falcon SG1K-1T

Summary of Contents for Falcon SG1K-1T

  • Page 1 All other brand names and trademarks are the property of their respective owners. The information stated in this document is subject to change without notice. 2004-02-02 Falcon ® , Falcon® Electric and UPS Plus logos are registered trademarks of Falcon Electric Inc...

  • Page 2: Important Safety Instructions

    CAUTION When replacing the UPS batteries, use the same number and type of batteries. The batteries approved for the Falcon SG1K-1T & SG1K-2T models are as follows: 3 pieces of Yuasa/Enersys NP7-12, 7Amp Hour, 12Vdc VRLA Type Battery 3 pieces of CSB GP 1272 F2, 7.2 Amp Hour, 12Vdc VRLA Type Battery CAUTION NEVER dispose of batteries in a fire, as batteries will explode.
  • Page 3 COMMERCIAL LOSS, OR BREACH OF IMPLIED OR EXPRESSED WARRANTIES. ANY AND ALL SUCH LIABILITY IS EXPRESSLY EXCLUDED. IN NO EVENT SHALL FALCON ELECTRIC INC. BE RESPONSIBLE FOR ANY AMOUNT. IF FALCON ELECTRIC INC. DETERMINES THAT ANY THIRD PARTY SERVICE WORK HAS BEEN PERFORMED IMPROPERLY OR IN A MANNER INCONSISTENT WITH FALCON ELECTRIC INC.
  • Page 4 Battery Replacement Guideline Per the picture below detailing the SG1K-1T rear panel, remove the battery fuse. For SG1K- 2T models there is no rear panel mounted battery fuse. Go to step 2. Per the picture below remove the two screws securing the UPS top cover to the rear panel.
  • Page 5 Remove the two screws securing the battery hold-down bracket. Next, unplug the sensor board connector. 2 screws securing hold down bracket Unplug top sensor Battery hold down board connector bracket Remove the third screw securing the battery hold-down bracket (see detail picture) Third screw securing the battery hold down bracket...
  • Page 6 Note the position of the three batteries and remove them from the chassis. See the battery connection diagram below. CAUTION WHEN REMOVING AND INSTALLING THE NEW BATTERIES, EXTREME CARE MUST BE USED NOT TO SHORT METAL CHASSIS PARTS ACROSS THE BATTERY TERMINALS AND NOT TO SHORT THE BATTERIES TO EACH OTHER OR PERSONAL INJURY MAY RESULT.
  • Page 7 This is necessary to precharge the UPS electronics. If the UPS is model SG1K-1T, reconnect the Black 15- wire to the - (black) terminal of BATT 1 as shown in the battery connection diagram on the previous page.
  • Page 8 Gently place the UPS on its side with the bottom facing you. Reinstall the four screws removed in step 4 and tighten. If the UPS is model SG1K-1T reinstall the battery fuse and cap. Connect the UPS to an utility power source.

This manual is also suitable for:

Sg1k-2t

Table of Contents