Residual Risks - Black+Decker BDEL501 Manual

ENGLISH
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
5. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Additional power tool safety warnings
Warning! Additional safety warnings for grinding,
sanding, wire brushing, polishing or abrasive cutting-
off operations
Wear ear protectors. Exposure to noise can cause hear-
u
ing loss.
Use auxiliary handles supplied with the tool. Loss of
u
control can cause personal injur.
Hold power tool by insulated gripping surfaces when
u
performing an operation where the cutting accessory
may contact hidden wiring or its own cord.Cutting ac-
cessory contacting a "live" wire may make exposed metal
parts of the power tool "live" and could give the operator
an electric shock.
Never use a chisel accessory in rotary mode. The acces-
u
sory will bind in the material and rotate the drill.
Use clamps or another practical way to secure and sup-
u
port the workpiece to a stable platform. Holding the work
by hand or against your body leaves it unstable and may
lead to loss of control.
Before drilling into walls, floors or ceilings, check for the
u
location of wiring and pipes.
Avoid touching the tip of a drill bit just after drilling, as it
u
may be hot.
The intended use is described in this instruction manual.
u
The use of any accessory or attachment or performance
of any operation with this tool other than those recom-
mended in this instruction manual may present a risk of
personal injury and/or damage to property.
6
(Original instructions)
Safety of others
This appliance is not intended for use by persons (includ-
u
ing children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concern-
ing use of the appliance by a person responsible for their
safety.
Children should be supervised to ensure that they do not
u
play with the appliance.

Residual risks.

Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
Injuries caused by touching any rotating/moving parts.
u
Injuries caused when changing any parts, blades or ac-
u
cessories.
Injuries caused by prolonged use of a tool. When using
u
any tool for prolonged periods ensure you take regular
breaks.
Impairment of hearing.
u
Health hazards caused by breathing dust developed when
u
using your tool (example:- working with wood, especially
oak, beech and MDF.)
Vibration
The declared vibration emission values stated in the technical
data and the declaration of conformity have been measured
in accordance with a standard test method provided by EN
60745 and may be used for comparing one tool with another.
The declared vibration emission value may also be used in a
preliminary assessment of exposure.
Warning! The vibration emission value during actual use of
the power tool can differ from the declared value depending
on the ways in which the tool is used. The vibration level may
increase above the level stated.
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons regularly
using power tools in employment, an estimation of vibration
exposure should consider, the actual conditions of use and the
way the tool is used, including taking account of all parts of the
operating cycle such as the times when the tool is switched off
and when it is running idle in addition to the trigger time.
Labels on tool
The following pictograms are shown on the tool: