H.C Duke & Son Freedom 360 Degrees Series Operator’s Manual With Illustrated Parts List page 160

1. Instruct the owner/operator on proper
cleaning and sanitizing as outlined
in the Operator's Manual. .......................
2. Drain sanitizer from the freezer. .............
3. Pour at least 2-1/2 gallons of mix into
each mix container. ................................
4. Open dispensing spigot and air
relief/bleed plug. Turn MTS switch to
"ON". Leave spigot open until pure mix
comes out of dispensing head then close
spigot. Close air relief/bleed plug when
mix is coming out of the air relief/bleed plug
opening in the bottom of the head. .......
1. Check refrigerant charge - sight glass. ............................................................................ First check
2. Check, set and record head pressure. .......................................................................... First check
3. Check, set and record cylinder expansion valve pressure. ........................................... First check
Note: Cabinet refrigeration must be turned off while checking. (Some models)
4. Check and record cabinet suction pressure. ................................................................ First check
NOTE: cylinder refrigeration must be turned off while checking. (Some models) Second check
5. On freezers equipped with adjustable timers. Check and record settings. ................ Beater Delay
6. What product is being used. ................................................................................................. A Side
7. Set cylinder thermostat to maintain desired temperature.
Record settings. ............................................................................................................. First check
8. Check and record actual product dispensing temperature. .......................................... First check
9. Check and record air meter size. .......................................................................................... Check
10. Make sure freezer cycles off with all microswitch spigot rods removed. ........................................
11. Make sure spigot rod starts the appropriate side and the freezer cycles off after activation in
the amount of time set on the dispense timer. ................................................................................
12. Reinstall all panels and panel screws. .............................................................................................
NOTE: Wait approximately two (2) hours and recheck and record all installation adjustments again.
Verify freezer is properly set. This check should be recorded in the second check column.
Remarks: __________________________________________________________________________________________________
Installation Checked and Inspected By:
Print Name: ______________________________ Signature: __________________________________ Date: _________________
Check one: Distributor
Operator/Owner Training Completed By:
Print Name: ______________________________ Signature: __________________________________ Date: _________________
Check one: Distributor
I hereby certify this equipment has been inspected and is in satisfactory operating condition. It has been demonstrated for proper start-up and
operating procedures. The potential dangers which could occur if the freezer is not operated properly have been explained to me and I have
read and understand the warranty attached to the Warranty Registration Card.
Signature required.
Print Name: ______________________________ Purchaser:
Print Name: _______________________________ Operator:
IMPORTANT: Installer and owner retain copy for reference.
IMPORTANT: MAIL WARRANTY REGISTRATION CARD TO VALIDATE AND START WARRANTY PERIOD.
Page 2
Owner/Operator Training
Machine Start-up
A B
Left Right
5. Allow MTS to run until it shuts off on
Side Side
pressure. ...................................................
6. Turn selector switch to "AUTO" ................
7. Allow refrigeration to cycle, record cycle
times once down to dispensing temperature
(approxiamtely 15-20 minutes).
Length of on time and off time ........... ON ______
8. Completely review all portions of freezer
start-up. ....................................................
9. Explain overrun, how to check, calculate
and change. ..............................................
10. Explain and have operator/owner sign
warranty card. ...........................................
Installation Adjustments
Beater Recycle (High Capacity Models)
Dispense (High Capacity Models)
Service Agency
Service Agency
_________________________________ Date: _________________
_________________________________ Date: _________________
OFF ______
A
Left Side
Second check
_____psig
Second check _____psig
_____psig
Second check _____psig
_____psig
_____psig
________
Compressor Delay ________
________
________
__________________
B Side __________________
___/___
Second check ___/___
_____°F
Second check _____°F
Beater Delay _____
Compressor Delay _____
_____
A B
Left Right
Side Side
______
______
B
Right Side
_____psig
_____psig
_____psig
_____psig
_______
_______
_______
_______
___/___
___/___
_____°F
_____°F
_____
_____
_____
INS-805 Rev. 01, 2/08