Figure 6 COM port ..................22 Figure 7 Turning on the system ..............23 Figure 8 VESA Mounting Hole Locations ........... 24 Figure 9 Panel Mount Cut-out hole and maximum panel thickness ... 25 Figure 10 Panel Mounting ................26 KPC-1900 User’s Manual...
Turn off system power, turn off the power supply, and then disconnect the power cord from its source before removing the chassis cover. Turning off the system power switch does not remove power to components. KPC-1900 User’s Manual...
ESD procedure to reduce the risk of damage to components. We strongly encourage you to follow proper ESD procedure, which can include wrist straps and smocks, when servicing equipment. You can also take the following steps to prevent damage from electrostatic KPC-1900 User’s Manual...
Page 7
Just before unwrapping the antistatic packaging, be sure you are at an ESD workstation or grounded. This will discharge any static electricity that may have built up in your body. KPC-1900 User’s Manual...
Page 8
Handle components and boards with care. Don’t touch the components or contacts on a board. Hold a board by its edges or by its metal mounting bracket. Do not handle or store system boards near strong electrostatic, electromagnetic, magnetic, or radioactive fields. KPC-1900 User’s Manual...
(domestic environment) is likely to cause harmful interference, in which case the user will be required to correct the interference (take adequate measures) at their own expense. Changes or modifications not expressly approved by us could void the user's authority to operate the equipment. KPC-1900 User’s Manual...
Refer to the “Specifications” section of this user’s guide for the operating and storage humidity specifications. Altitude Operating a system at a high altitude (low pressure) reduces the efficiency of the cooling fans to cool the system. This can cause electrical problems related KPC-1900 User’s Manual...
Page 11
Surge protectors should be used with all UPS systems, and the UPS system should be Underwriters KPC-1900 User’s Manual...
Chapter 1 Introduction Overview Powered by 6th Generation Intel® Skylake S-Series Processors, KPC-1900 Panel PC has greatly improved graphics performance, power efficiency and wireless connectivity. In addition to 1x DVI-D, 2x DP, 4x USB 3.0, 2x USB 2.0, 3x...
Power Adapter: AC to DC, 100 V ~ 240 V Firmware BIOS: AMI uEFI BIOS w/ 128 Mb SPI Flash Watchdog: Programmable WDT to generate system reset event H/W Monitor: Input & Core Voltages, CPU & System Temperatures KPC-1900 User’s Manual...
The eight-pin RJ-45 LAN port supports a standard Ethernet cable for connection to a local network. Power Input The supplied power adapter converts AC power to DC for use with this phoenix connector or DC jack. Power supplied through this connector supplies power to KPC-1900 User’s Manual...
Page 17
MIC-IN (Pink) The microphone jack is designed to connect the microphone used for video conferencing, voice narrations, or simple audio recordings. Line-IN (Blue) The Line-in jack is designed to take input from a higher-powered sound source. KPC-1900 User’s Manual...
Chapter 2 Chapter 2 Getting Started Setting up your PC Connecting the monitor Connect the DP / DVI-D cable from your display to the DP / DVI-D port. DVI-D DVI-D Figure 3 DP / DVI-D KPC-1900 User’s Manual...
Chapter 2 Connecting USB mouse & keyboard Your KPC-1900 does not come with a keyboard and mouse, but you can use any USB keyboard or mouse with your computer. Figure 4 Connect USB mouse & keyboard NOTE Using a third-party USB mouse or keyboard may require software drivers.
Chapter 2 Connecting to a network device Connect one end of a network cable to the LAN port on the system rear panel and the other end to a hub or switch. Figure 5 RJ45 connector KPC-1900 User’s Manual...
3. Connect the other end of the AC power cable to a corresponding AC power outlet. 4. Press the power switch on the I/O panel to turn on the system. Power Switch DC In (Phoenix Connector) Power Switch DC In (DC Jack) Figure 7 Turning on the system KPC-1900 User’s Manual...
Use 4 screws with the appropriate length for your mounting bracket. Figure 8 VESA Mounting Hole Locations NOTE To fasten the metal shelf, your monitor must comply with VESA75 or VESA100 standard. The VESA mounting kit is optional. KPC-1900 User’s Manual...
The Panel PC can be panel mounted and comes with brackets and screws for this purpose. The required cutout for panel mounting and maximum panel thickness is shown below. Figure 9 Panel Mount Cut-out hole and maximum panel thickness KPC-1900 User’s Manual...
Insert a Panel Mount Secure brackets to Panel Opening Covers from the Bracket into each by tightening the screws chassis with Phillips Bracket Opening Screwdriver (3 on top edge, 3 on bottom edge) Figure 10 Panel Mounting KPC-1900 User’s Manual...
It is possible for the CMOS battery to fail, which will cause data loss in the CMOS only. If this happens you will need to reconfigure your BIOS settings. KPC-1900 User’s Manual...
+/-: Change Opt. Frequency 2133 MHz F1: General Help F2: Previous Values F3: Optimized Defaults System date [Fri 11/25/2016] F4: Save & Reset System time [14:17:17] ESC: Exit Access Level Administrator Version 2.17.1254. Copyright (C) 2016, American Megatrends, Inc. KPC-1900 User’s Manual...
[Enabled] Version 2.17.1254. Copyright (C) 2016, American Megatrends, Inc. SATA Controller(s) Options: Enabled, Disabled SATA Mode Selection Options: AHCI, RAID Serial STS Port 1/2/3/4 Port 1/2/3/4 Options: Disabled, Enabled mSATA Port 1/2 Port 1/2 Options: Disabled, Enabled KPC-1900 User’s Manual...
F4: Save & Reset USB Mass Storage Driver Support [Enabled] ESC: Exit Version 2.17.1254. Copyright (C) 2016, American Megatrends, Inc. Legacy USB Support Options: Enabled, Disabled XHCI hand-off Options: Enabled, Disabled USB Mass Storage Driver Support Options: Disabled, Enabled KPC-1900 User’s Manual...
+/-: Change Opt. Un-Configure ME [Disabled] F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Reset ESC: Exit Version 2.17.1254. Copyright (C) 2016, American Megatrends, Inc. Intel AMT Options: Disabled, Enabled Un-Configure ME Options: Disabled, Enabled KPC-1900 User’s Manual...
: +3.360 V F4: Save & Reset +VRTC : +3.216 V ESC: Exit +1.05V : +1.080 V Version 2.17.1254. Copyright (C) 2016, American Megatrends, Inc. CPU Warning Temperature Options: Disabled, 80 C, 85 C, 90 C, 95 C KPC-1900 User’s Manual...
Version 2.17.1254. Copyright (C) 2016, American Megatrends, Inc. Full Screen LOGO Display Options: Disabled, Enabled Bootup NumLock State Options: On, Off CSM Support Options: Enabled, Disabled Boot Option Filter Options: UEFI and Legacy, Legacy only, UEFI only KPC-1900 User’s Manual...
Load Optimal Default values for all the setup values. This option allows you to load failsafe default values for each of the parameters on the Setup menus, which will provide the most stable performance settings. The F8 key can be used for this operation. KPC-1900 User’s Manual...
You can download the drivers for the KPC-1900 from our website and install as instructed there. For other operating systems, please contact us. KPC-1900 User’s Manual...