Table of Contents
Advertisement
Quick Links
Pioneering for You
Wilo-Drain TMT 32M
de Einbau- und Betriebsanleitung
en Installation and operating instructions
fr
Notice de montage et de mise en service
tr
Montaj ve kullanma kılavuzu
6069279 Ed02-05/2015 WH
pl
Instrukcja montażu i obsługi
cs Návod k montáži a obsluze
ru Инструкция по монтажу и эксплуатации
uk Iнструкція з монтажу та експлуатації
Advertisement
Table of Contents
Related Manuals for Wilo Drain TMT 32M
Summary of Contents for Wilo Drain TMT 32M
- Page 1 Pioneering for You Wilo-Drain TMT 32M de Einbau- und Betriebsanleitung Instrukcja montażu i obsługi en Installation and operating instructions cs Návod k montáži a obsluze Notice de montage et de mise en service ru Инструкция по монтажу и эксплуатации uk Iнструкція з монтажу та експлуатації Montaj ve kullanma kılavuzu 6069279 Ed02-05/2015 WH...
- Page 2 Fig. 1 Fig. 3 M 3~ Fig. 2 Fig. 4 : 95 °C : 75 °C...
-
Page 3: Table Of Contents
6.1. Electrical system 6.2. Rotation control 6.3. Level control 6.4. Commissioning 6.5. Safety rules during operation Decommissioning/disposal 7.1. Temporary decommissioning 7.2. Decommissioning for maintenance work or stor- 7.3. Removal 7.4. Return delivery/storage 7.5. Disposal Installation and operating instructions Wilo-Drain TMT 32M... -
Page 4: Introduction
This operating and maintenance manual has been copyrighted by the manufacturer. The operating In general, repairs should only be carried out by and maintenance manual is intended for use by Wilo customer service. installation, operating and maintenance person- nel. It contains regulations and drawings which 1.5.6. Disclaimer may not be reproduced or distributed, either No warranty claims will be accepted or liability... -
Page 5: Safety
Instruction symbol, for example, wear protec- These instructions must be strictly observed. tive clothing Non-observance can result in injury or substan- tial material damage. The safety symbols used conform to the generally applicable directives and regulations, such as DIN and ANSI. Installation and operating instructions Wilo-Drain TMT 32M... -
Page 6: Electrical Work
• Pumps that have been operated in sewage water containing faeces and/or fluids that are hazardous The pumps are equipped with a thermal winding to health must be decontaminated before being monitor and leakage connection for the motor. The pump is switched off if the motor gets too used with other fluids. WILO SE 04/2014 V05 DIN A4... -
Page 7: Sound Pressure
3.2. Set-up the pump is running at its duty point and under all The Wilo-Drain TMT 32M pumps are submersi- operating conditions. ble drainage pumps that are suitable for vertical operation in portable wet well installation. -
Page 8: Operating Modes
Non-immersed: 3…75 °C (37...167 °F) • On pump side: SiC/SiC • On motor side: Carbon/steatite 3.5. Type key 3.3. Operating modes Example: Wilo-Drain TMT 32M113/7.5Ci Tauchmotorpumpe (submersible pump) 3.3.1. Operating mode S1 (permanent operation) The pump can operate continuously at the rated Pumping of wastewater load without exceeding the permissible temper- Pressure connection G 1¼ (DN 32) -
Page 9: Storage
5.2. Installation methods Damaged coatings must be repaired immedi- • Vertical portable wet well installation with ately. Only an intact coating fulfils its intended • Fixed discharge pipeline connection purpose. • Pressure hose Installation and operating instructions Wilo-Drain TMT 32M... -
Page 10: Installation
5.3.2. Portable wet well installation being switched back on if the motor has been The pump can be positioned anywhere in the taken out of the fluid! operating space using the built-in pump foot. WILO SE 04/2014 V05 DIN A4... -
Page 11: Dry-Running Protection
If the dry-running protection only includes Work steps one floater or electrode and the fill levels deviate Preparing pumps: about 1 h significantly, then the pump may turn on and • Fit the pipe elbow to the pressure connection off constantly! This can result in the maximum using the hose connection. Installation and operating instructions Wilo-Drain TMT 32M... -
Page 12: Electrical Connection
English INSTALLATION number of motor activations (switching cycles) ing unit may be defective. Do not connect the being exceeded. pump and consult Wilo customer service. 5.4.1. Remedies for avoiding excessive switching Insulation resistance of the motor winding cycles Before connecting the power supply cable, the insulation resistance must be tested. This can be •... -
Page 13: Motor Protection And Activation Types
A test run must be performed under general op- erating conditions! monitored: • Type of installation 6.2.1. Checking the direction of rotation • Operating mode • Minimum water submersion/max. immersion The direction of rotation must be checked with a depth rotating field tester by a local electrician. For the Installation and operating instructions Wilo-Drain TMT 32M... -
Page 14: Level Control
• The following points must also be checked for • When carrying out work in basins and/or tanks, wet well installation: the respective local protection measures must be observed. A second person must be present for • Clean the pump sump of coarse contaminants safety reasons. • Open all slide valves on the pressure side • Only lifting equipment that is in a technically perfect condition and load-carrying equipment WILO SE 04/2014 V05 DIN A4... -
Page 15: Temporary Decommissioning
• This manual must be available to and observed 7.4. Return delivery/storage by the maintenance staff. Only maintenance and repair work described in this manual may be For shipping, the parts must be packed in tear- carried out. proof plastic bags of sufficient size in such a Installation and operating instructions Wilo-Drain TMT 32M... -
Page 16: Operating Materials
English MAINTENANCE AND REPAIR Any other work and/or alterations to the • BP WHITEMORE WOM 14* construction must only be carried out by Wilo • Texaco Pharmaceutical 30* or 40* customer service. All oil types marked with “*” are approved for use with foods in accordance with “USDA-H1”. • When carrying out work in basins and/or tanks, the respective local protection measures must be Filling quantities observed in all cases. A second person must be •... -
Page 17: Maintenance Work
Make sure that the pump cannot fall over and/ power supply cable must be replaced. or slip. The cables may only be replaced by Wilo customer service or an authorised or certified Carefully and slowly unscrew the screw plug. service workshop. The pump may only be start-... - Page 18 • Replace worn parts Impeller blocked or slowed Defective motor bearing • Switch off pump, secure it against being • Contact the manufacturer switched back on again and free the impeller 9. Pump is installed under tension Faulty hose/piping • Check installation, use expansion joints if • Replace defective parts necessary WILO SE 04/2014 V05 DIN A4...
-
Page 19: Appendix
APPENDIX English Further steps for troubleshooting If the points listed here do not rectify the fault, contact Wilo customer service. They can help you as follows: • Telephone or written support from Wilo Customer Service • On-site support from Wilo customer service • Inspection or repair of the pump at the factory Please note that you may be charged for some services provided by our customer service. For... - Page 20 WILO SE Nortkirchenstraße 100 44263 Dortmund Germany T +49 (0)231 4102-0 F +49 (0)231 4102-7363 wilo@wilo.com Pioneering for You www.wilo.com...
Need help?
Do you have a question about the Drain TMT 32M and is the answer not in the manual?
Questions and answers