Wayne WAPC250 Operating Instructions And Parts Manual
Auto on-off water removal pool cover pump
Hide thumbs
Also See for WAPC250:
- Operating instructions and parts manual (21 pages) ,
- Quick start instructions (21 pages) ,
- Operating instructions & parts manual (8 pages)
Advertisement
Operating Instructions and Parts Manual
SPECIFICATIONS
POWER SUPPLY REQUIREMENTS
MOTOR
HORSEPOWER
CIRCUIT REQUREMENT
LIQUID TEMPERATURE RANGE
© 2018, WAYNE/Scott Fetzer Company
120 V, 60 Hz
Single Phase, Auto ON/OFF
1/4 HP
15 A (minimum)
40° F- 120° F
PERFORMANCE
Model
HP
Discharge Head
WAPC250
1/4
Auto On-Off Water Removal
Please read and save these instructions. Read carefully before attempting to assemble, install,
operate or maintain the product described. Protect yourself and others by observing all safety
information. Failure to comply with instructions could result in personal injury and/or property
damage! Retain instructions for future reference.
MOTOR HOUSING
MOTOR SHAFT
IMPELLER
VOLUTE
PUMP DISCHARGE
0 ft.
5 ft.
Gal/hr
3000
2350
www.waynepumps.com
Pool Cover Pump
CONSTRUCTION
Thermoplastic
Stainless Steel
Thermoplastic
Thermoplastic
1-1/4 in. with Check Valve & 3/4 in. Hose
Threads
10ft.
15 ft.
1600
900
690001-001 B 08/18
WAPC250
Advertisement
Table of Contents
Related Manuals for Wayne WAPC250
Summary of Contents for Wayne WAPC250
- Page 1 1-1/4 in. with Check Valve & 3/4 in. Hose LIQUID TEMPERATURE RANGE 40° F- 120° F Threads PERFORMANCE Model Discharge Head 0 ft. 5 ft. 10ft. 15 ft. WAPC250 Gal/hr 3000 2350 1600 © 2018, WAYNE/Scott Fetzer Company www.waynepumps.com 690001-001 B 08/18...
- Page 2 Operating Instructions and Parts Manual STEP 1 - VERIFY PACKAGE CONTENTS STEP 5 - SECURE ROPE TO STRAINER FEED ROPE THROUGH LOOP ON STRAINER AND (1) POOL COVER PUMP SECURE WITH KNOT (1) CHECK VALVE/ HOSE ADAPTER (1) 25' ROPE (1) PUMP STRAINER STEP 2 - INSTALL CHECK VALVE STEP 6 - POSITION ON POOL COVER...
-
Page 3: General Safety Information
The units are equipped with a 25 ft. 3-prong grounding type power cord (WAPC250) or GFCI Protected Power Cord (WAPC250G). The provided discharge check valve prevents short cycling and it's 3/4 in. -
Page 4: Application And Operation
Operating Instructions and Parts Manual APPLICATION AND OPERATION GENERAL SAFETY INFORMATION (CONT’D) Do NOT use pump if any part of the housing Risque de choc électrique! Le disjoncteur de switch or probe is cracked, broken, or missing. fuite à la terre fournira une protection uniquement contre les défauts entre les lignes et les fuites à... - Page 5 Operating Instructions and Parts Manual WAPC250 APPLICATION AND OPERATION (CONT’D) DROP-IN PUMP APPLICATION PUMPING HEIGHT When water is pumped to an elevated position, any volume that 13' MAXIMUM AVOID PINCHING OR DAMAGING PUMPING HEIGHT has not reached the discharge outlet can flow back through the...
- Page 6 Operating Instructions and Parts Manual ABOVE GROUND PUMP INSTALLATION To aid in pump placement on pool cover, secure provided 25 ft. rope to the pull to shore loop (Figure B). FEED ROPE THROUGH LOOP AND SECURE WITH KNOT 25 FT. (INCLUDED) ROPE Figure D - Above Ground Installation...
- Page 7 Operating Instructions and Parts Manual WAPC250 ABOVE GROUND – PUMP REMOVAL 9. The pump will stop automatically once water has been removed to a depth of approximately 3/4 of an inch. The pump will not restart until the water depth rises to 2-1/8 inches or greater.
-
Page 8: Maintenance
Operating Instructions and Parts Manual MAINTENANCE TROUBLESHOOTING 1. Periodic cleaning is required to maintain performance of the 1. Verify pumping height does NOT exceed 13 feet (See Figure A). If pump. Follow the cleaning steps listed below: pumping height is greater than 13 feet, this pumps automatic feature a. -
Page 9: Troubleshooting Chart
Operating Instructions and Parts Manual WAPC250 automatically shutdown to protect the motor from overheating. The TROUBLESHOOTING (CONT’D) pump will continue this on/off cycle for a period of time to attempt to 6. If the pump cycles on and off too often the electronic switch “free”... - Page 10 For Replacement Parts or Customer Support, Call 1-800-237-0987 Please provide following information: Address parts correspondence to: - Model number Wayne Water Systems - Serial number (if any) 101 Production Drive - Part description and number as shown in parts list Harrison, OH 45030 U.S.A.
- Page 11 LIMITED WARRANTY For three years for WAPC250 model from the date of purchase, from an authorized dealer, Wayne Water Systems will repair or replace, at its option for the original purchaser, any part or parts of its Pool Cover Pump or Water Pumps (“Product”) found upon examination by Wayne Water Systems to be defective in materials or workmanship.
- Page 12 NOTES www.waynepumps.com...