Table of Contents
Advertisement
Quick Links
Installation and Service
®
Pulse
Metered Dispense
Valve Oil Bar
For fixed mounting of up to three Pulse metered dispense valves.
Not approved for use in explosive atmospheres or hazardous locations. For professional
use only.
Model No.: 25D130 - Configures metered dispense valves for installation in the
oil bar.
NOTE: One Model 25D130 is required for each model 24N415 metered dispense valve.
Maximum Working Pressure: 1500 psi (103 bar,10 MPa)
Model No.: 25D121 - Oil Dispenser Bar
Important Safety
Instructions
Read all warnings and instructions
in this manual and all related Pulse
system manuals. Save all
instructions.
Related Manuals
3A5412 - Pulse Metered Dispense Valve
Refer to Parts, page 8 for reference numbers
used in these instructions.
3A5573C
EN
Advertisement
Table of Contents
Related Manuals for Graco Pulse 25D130
Summary of Contents for Graco Pulse 25D130
- Page 1 Installation and Service ® Pulse Metered Dispense 3A5573C Valve Oil Bar For fixed mounting of up to three Pulse metered dispense valves. Not approved for use in explosive atmospheres or hazardous locations. For professional use only. Model No.: 25D130 - Configures metered dispense valves for installation in the oil bar.
-
Page 2: Installation
Installation Installation Prepare the Metered Dispense Valve for Installation Secure the metered dispense valve in a Install Graco identification label (7) over vise (F . 1). the existing GRACO identification label in the orientation shown in F . 4. Install strainer (9) and fitting (3) in the inlet (F . - Page 3 Installation Assemble the Oil Bar The oil bar requires assembly prior to use. Attach the meter mounting plate (24) to the wrapper dispenser (21) using screws Attach dispenser wrapper (21) to drain (27), lock washers(28) and nuts (29) and pan (22) using screws (27), lock existing holes.
- Page 4 Installation Install the Metered Dispense Valve in the Oil Bar Wrap threads of pipe nipple (8) with Position manifold (2) inside oil bar, orienting opening (a) on the front of the PTFE tape or thread sealant as shown in manifold with opening (b) in the .
- Page 5 Installation Install the metered dispense valve in oil Install the end of the nipple adapter (10) bar housing by connecting fitting (1) on that was wrapped in the PTFE tape or metered dispense valve to pipe nipple treated with thread sealant into the (8) in manifold (2) as shown in F .
-
Page 6: Pressure Relief Procedure
Repair and Maintenance Repair and Maintenance Pressure Relief Procedure Oil Bar Disassembly Relieve pressure. See the Pressure WARNING Relief Procedure. Disconnect fluid distribution lines (c) from fitting (3) (see F . 17). PRESSURIZED FLUID HAZARD This equipment stays pressurized until pressure is manually relieved. -
Page 7: Repair And Maintenance
Repair and Maintenance Remove screws (27) and access panel (25) (see F . 19). . 21 Remove screws (5) and washers (4) from manifold (2). Lift manifold (2) straight up and out of the oil bar housing . 22). . 19 Disconnect fitting (1) from pipe nipple (8) in manifold (2) as shown in F . - Page 8 Parts Parts Model 25D130 Ref Part No. Description 131244 FITTING, 3/4 ORB UNF X 3/8 NPSM 131245 MANIFOLD, dispenser 131246 FITTING, 1-1/16 ORB UNF X 1/2 NPSM 100016 WASHER, lock 108296 SCREW, hex 121079 SWIVEL, elbow, ORB X NPSM 130195 LABEL, brand, oil bar 156849 PIPE, nipple...
- Page 9 Parts Model 25D121 Part No. Description Part No. Description 108296 SCREW, hex 181316 WRAPPER, dispenser 100016 WASHER, lock 16D537 PAN, drain, coating 100015 NUT, hex 181319 STRAINER, pan 159346 WASHER 131242 PLATE, mount * Extra parts included for connecting multiple oil 131243 PLATE, cover panel bars together.
-
Page 10: Technical Specifications
Technical Specifications Technical Specifications Oil Bar Metric Maximum Working Pressure 1500 psi 103 bar, 10 MPa Wetted Materials Carbon steel, aluminum, Buna-n rubber Weight Model 25D121 30 lbs 13.61 kg Model 25D130 5 lbs 2.26 kg 3A5573C... - Page 11 NOTES NOTES 3A5573C...
-
Page 12: Graco Standard Warranty
With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective.