Table of Contents
Advertisement
1. Safety
X 2.5
110-180Vac
180-240Vac
X 4
110-180Vac
180-240Vac
The power limits of the used power connectors needs to be followed. A C13/C14 connector is limited to 10A. An Amphenol connector
is limited to 16A.
ESD and LED's:
LED components used in X-series tiles are ESD (Electro-Static Discharge) sensitive. To prevent the possibility of destroying LED
components do not touch either in operation or while switched off. Always use ESD-gloves.
Disconnect device:
When the appliance inlets of the individual tiles are not accessible, the socket outlets supplying the rack shall be installed near the
equipment and be easily accessible, or a readily accessible general disconnect device shall be incorporated in the fixed wiring.
This equipment MUST be earthed:
In order to protect against risk of electric shock, the installation should be properly grounded. Defeating the purpose of the grounding
type plug will expose you to the risk of electric shock.
Power system:
It is recommended to use a TN-S power distribution system (a power distribution system with a separate neutral and grounding
conductor) in order to avoid large ground current loops due to voltage differences in the neutral conductor. The total electrical
installation should be protected by an appropriately rated disconnect switch, circuit breakers, over voltage protector and Ground Fault
Current Interrupters. The installation shall be done according to the local electrical installation codes. In Europe special attention
should be given to HD 60364, Harmonization Document for electrical installation of buildings. In Germany VDE 0100 should be
adhered to. In America, special attention should be given to the National Electrical Code, ANSI/NFPA 70.
Mains cords:
The power cords delivered with this system have special properties for safety. They are not user serviceable. If the power cords are
damaged, replace them only with new ones. Never try to repair a power cord.
LEDs:
The LEDs used on the X-series tiles are fragile. Never push with a hard or sharp object onto the lens of the LED as this may cause
damage to the LED. The maximum allowed load upon the lens of the LED is 300 gram/LED. Be careful when installing a shader
upon the X-series tiles. Shaders only fit in one direction and this should be verified before pushing into final position. Use your bare
fingers (not nails) to press the shader over the LEDs. Use your finger nails to press upon the framework of the shader between the
LEDs (not upon the LEDs) to push the shader in its final position.
Do not hot plug:
Do not hot plug any cables. Damage to the connector pins may occur. Resulting damage is not covered under warranty.
Maximum allowed display height:
The maximum height of a X-series display in:
In a hanging configuration:
•
with traditional truss : 25 tiles
•
with auto balancing truss in combination with X1.2 or X1.5: 20 tiles
•
with auto balancing truss in combination with X2.5 or X4.0: 24 tiles
In base stand setup configuration:
•
with traditional beam: 25 tiles
•
with auto balance truss: 20 tiles
When using back mounting, the maximum height is unlimited.
1.5
Proper usage
Proper usage of X-series tiles
•
No part of the X-series tile can come in contact with any type of moisture.
•
No part of the X-series tile can come in contact with any type of abrasive.
•
No part of the X-series tile can come in contact with any type of dust.
•
No part of the X-series tile can come in contact with any type of corrosive substance.
•
Using the LED product in an environment with high corrosive gasses (e.g. Sulphur) can lead to discoloration of the materials.
This discoloration gives a change in brightness of the product. This could lead to uniformity differences and possibly also to
failures. Each use of the product in this kind of environment needs to be checked up-front with the supplier.
4
10 tiles
14 tiles
10 tiles
14 tiles
R5906876 X-SERIES 24/07/2017
Advertisement
Table of Contents
