Distance To Combustible Material - Nordpeis Duo Series Installation And User Manual

Flue (Ø mm)
Flue gas temperature at flue
connector (°C)
Draft at flue connector
recommended (Pa)
Data according to
EN 13 240
Nominal heat output (kW)
Efficiency (%)
CO @ 13% O (%)
2
Flue gas temperature (°C)
Draft (Pa)
Fuel recommended
Fuel length recomended
(cm)
Fuel charge (kg)
Refueling interval (minutes)
Opening of the air vent
control (%)
Operation
* Intermittent combustion refers to normal use of a fireplace, i.e. new
wood is inserted when the previous load has burned down to ember
Warning: If the requirements for ventilation are
NOT complied with, the cooling airflow around the
product will be considerably reduced and
the product can overheat.
This can cause a fire.

3. Distance to combustible material

Ensure that the safety distances are respected
(FIG 1).
When connecting a steel chimney to the top outlet use
the security distances required from the manufacturer.
4. Assembly
The following tools are necessary:
•
5 mm Allen key (included)
•
10/17 mm wrench (included)
•
Phillips screwdriver
Releasing the stove from the pallet:
Duo 1: Remove the lid that covers the rear of
the pedestal with a 10 mm wrench, unfasten the
transportation lock.
Outer Ø 150 mm
*Alternative versions
exsists due to National
requirements
315
15 - 25
5
80,4
0,10
271
14
Wood
25-30
1,1kg
45
50
Intermittent*
GB
Duo 2: Two iron fasteners are screwed onto the pallet
and inserted through the back plate. Loosen these.
Next step is to remove the lower lid on the front of the
stove. It is fastened at the top with two clips at each
side. Pull the lid carefully outwards from the top and lift
it out of the two fasteners at the bottom. On the inside
of the lid there are two screws that must be unfastened
before the product can be removed from the pallet.
Duo 4/5/6: Open the door under the combustion
chamber. Unscrew the four screws that fasten the stove
to the pallet.
Operating control
When the stove is in an upright position, and prior
to connecting it, control that all functions are easy to
manoeuvre and appear satisfactory.
Door (FIG 3)
Handle is pulled out
Handle is pushed in
Air vent (FIG 4)
Forward
Backward
Installation of Thermotte™ FIG 15-21
1. If installing a Duo with lateral glass, the stainless
rails (FIG 15) must be removed before the
Thermotte plates are installed.
2. Install the Thermotte plates as shown in
FIG 16-20
3. On models with lateral glass the stainless rails are
placed as shown in FIG 21
Adjustment of legs
NB! Please note that the legs of Duo 2, 4 and 5/6 must
be adjusted upwards, about 8 mm, if a form-fitted floor
plate is used. Please also note that the height of the
flue/chimney connection will also change if the product
is raised.
Duo 1: Does not have adjustable legs
Duo 2 FIG 5-6: In order to adjust the front legs;
Remove the lower lid in front by tilting it out of the clips
at the top (A) and lifting it out from the bottom (B).
In order to adjust the rear legs; Remove the back plate
as shown in FIG 8-10D.
Use a 17 mm wrench in order to adjust the legs.
Duo 4/5/6 FIG 7: Open the door to the space under the
combustion chamber. Remove the 4 plastic lids and
adjust the legs with a 17 mm wrench. Put the plastic lids
back in place.
Flue outlet collar
Duo is delivered standard with a top flue outlet
collar.
Open
Close
Closed
Open
19