Distance To Combustible Material - Nordpeis Ronda User Manual

Surround
Insert
Material insert
Surface treatment
door / doorframe
Fuel
Nominal output
Efficiency
CO % @ 13% O
2
Draught system
Combustion system
Heating area
Flue outlet
Flue
Weight of insert
Weight of surround
Flue gas temperature 313 °C
Air supply
requirements (m³/h)
Fuel charge
Refueling interval
Opening of the air
vent control
Operation
* Intermittent combustion refers to normal use of a fireplace,
i.e. new wood is inserted when the previous load has burned
down to ember.
Warning: If the requirements for ventilation are
NOT complied with, the heating circulation effect
will be considerably reduced and
overheating can occur.
This can in a worst case scenario cause a fire.

4. Distance to Combustible Material

Firewall
Ensure that the safety distances are respected
(FIG 1).
When connecting a steel chimney to the top outlet use
the security distances required from the manufacturer.
5. Assembly
Assembly instructions for the insert (FIG 2 - FIG 12)
The following tools are necessary:
•
5 mm Allen key
•
13 mm spanner/wrench
•
Caulking gun (for the stove cement)
12
Ronda
S-26R (NI-26)
Steel/Cast iron
Heat resistant varnish
Wood logs, 30 cm
5 kW
79,3%
0,07
Air vent control
Secondary combustion
(clean burning)
60-120 m²
Top
Inner Ø 150 mm
(
*Alternative versions exsists due to
National requirements)
93 kg
239 kg
11
1,4 kg
56 min
50%
Intermittent*
1. Ensure that all the loose parts are included (FIG 2):
A. Insert with door and heat shield
B. 4 legs with adjusting bolts and lock nuts
C. 4 fastening bolts with disks for the legs
D. Handle for ash grate and ashtray
E. Glove
F. Assembly instructions
G. Warranty card
2. Carefully lay the insert on its back. Ensure that the
transportation padding is put inside the insert before
turning it over, so that the insulating plates in the
burn chamber do not fall down and break. Please
note that the insulating plates may release coloured
dust when touched. Avoid touching the cast iron with
dust on your fingers. In case of dust on any cast iron
part, the glove included is well suited to brush it off.
Start with assembling the legs (FIG 3) as follows:
•
Fasten the screws on to the insert with a 13 mm
spanner/wrench. The legs are placed as shown (the
opening in the legs should face outwards).
•
Use the adjusting bolts (FIG 4) and adjust the legs
to the desired height (X) before returning the insert
to an upright position (do not tilt the insert). The
height depends on the surround.
Regulation of leg height (X) for NI-26:
From: 210 mm To: 330 mm.
•
Flue outlet
S-26R is delivered standard with a top flue outlet collar.
In order to change to a posterior mounted flue outlet:
FIG 5A: Remove the perforated decoration lid in the
back with a hammer, or saw it out with a hacksaw
FIG 5B: Unscrew the sheet steel lid.
FIG 6: Unscrew the flue outlet collar with a 5 mm Allen key.
FIG 7: Fasten the sheet steel lid on the top flue outlet.
FIG 8: Fasten the collar on the posterior flue outlet.
Connection of the Flue
Please be aware when connecting the 150 mm flue to
the smoke outlet that the flue is placed outside the flue
outlet collar.
*Alternative versions exsists due to
National requirements
* The approximate centre height of the hole for the
flue is marked in the dimensioned drawing. Consider
possible inclination of the flue prior to perforating the
chimney. Distortions in floors and walls may influence
the height. Dry stack the fireplace for accurate height
and positioning of the flue/chimney connection. If
a fresh air supply set (accessory) is connected through
the floor, mark where the hole should be.
GB