Central Machinery 32966 Assembly And Operation Instructions Manual
  1. Manuals
  2. Brands
  3. Central Machinery Manuals
  4. Power Tool
  5. 32966
  6. Assembly and operation instructions manual
Central Machinery 32966 Assembly And Operation Instructions Manual

Central Machinery 32966 Assembly And Operation Instructions Manual

Rabbeting jointer 8” - with stand
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Brought To You By Augusta Flint
RABBeTING JOINTeR
8" - WITH STAND
Model
32966
ASSeMBly AND OpeRATION INSTRucTIONS
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
TO pReVeNT SeRIOuS INJuRy, ReAD AND uNDeRSTAND
All WARNINGS AND INSTRucTIONS BefORe uSe.
©
®
Copyright
2007 by Harbor Freight Tools
. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.

Advertisement

Table of Contents
loading

Related Manuals for Central Machinery 32966

Summary of Contents for Central Machinery 32966

  • Page 1 Brought To You By Augusta Flint RABBeTING JOINTeR 8” - WITH STAND Model 32966 ASSeMBly AND OpeRATION INSTRucTIONS Due to continuing improvements, actual product may differ slightly from the product described herein. ® 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our website at: http://www.harborfreight.com...

  • Page 2: Specifications

    Do not operate power tools in explosive atmospheres, such as in the pres- ence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes. for technical questions, please call 1-800-444-3353. SKU 32966 Page 2...

  • Page 3: Personal Safety

    Switch and disconnect the power cord before performing any inspection, maintenance, or cleaning procedures. Store idle tools out of reach of children and other untrained persons. Tools are dangerous in the hands of untrained users. for technical questions, please call 1-800-444-3353. SKU 32966 Page 3...
  • Page 4 Never leave the Rabbeting Jointer unattended when it is running. Turn off the tool before leaving the work area. Always feed the workpiece against the rotation of the knives (16). for technical questions, please call 1-800-444-3353. SKU 32966 Page 4...

  • Page 5: Mechanical Precautions

    Do not alter or adjust any part of the Rabbeting Jointer that is assembled by the manufacturer. Always perform scheduled maintenance completely. for technical questions, please call 1-800-444-3353. SKU 32966 Page 5...

  • Page 6: Grounded Tools: Tools With Three Prong Plugs

    Tools marked with “Grounding Required” have a three wire cord and three prong grounding plug. The plug must be connected to a properly grounded outlet. If the tool should electrically malfunction or break down, grounding provides a low fIGuRe A for technical questions, please call 1-800-444-3353. SKU 32966 Page 6...

  • Page 7: Extension Cords

    If you are using one extension cord for more than one tool, add the nameplate am- peres and use the sum to determine the required minimum cord size. (See figure B.) (115 Volt) fIGuRe B for technical questions, please call 1-800-444-3353. SKU 32966 Page 7...

  • Page 8: To Assemble The Stand

    Rear Side Plate (34A) with the two holes located at each end of the two Reinforcing Plates (3A) and with the two holes located at each end of the two Side Angle Plates (24A). (See Assy. Diagram.) for technical questions, please call 1-800-444-3353. SKU 32966 Page 8...
  • Page 9 Connect the bottom of the Upright Plate (4A) to the Crossbeam Plate (17A) using two Screws (16A), two Washers (18A), and two Nuts (19A). (See Assy. Diagram.) upRIGHT plATe (4A) ScReW (5A) WASHeR (7A) MOTOR (33A) lOck WASHeR (30A) NuT (6A) fIGuRe D for technical questions, please call 1-800-444-3353. SKU 32966 Page 9...
  • Page 10 Place the V-Belt (12) on the Motor’s (33A) V-Belt Pulley (32A). Then slide the Motor upward and pull the V-Belt (12) up and over the Cutter Head’s (8) Pulley (11). (See Assy. Diagram.) for technical questions, please call 1-800-444-3353. SKU 32966 Page 10...
  • Page 11 Front Table (2) and Rear Table (3) into grooves between the feNce BODy (4) fIGuRe e fRONT TABle (2) ReAR TABle (3) ADJuSTING WHeel (63) ADJuSTING WHeel (63) DepTH ScAle (7) pOWeR SWITcH (14A) for technical questions, please call 1-800-444-3353. SKU 32966 Page 11...
  • Page 12 If the spring tension is too much, or not enough, remove the Cutter Head Guard (42) and adjust the spring tension accordingly by rotating the Spring Knob (29). (See figure f and Assy. Diagram.) cuTTeR HeAD GuARD SpRING kNOB (29) fIGuRe f for technical questions, please call 1-800-444-3353. SKU 32966 Page 12...
  • Page 13 Rear Table (3). (See figure G and Assy. Diagram.) ScRAp WOOD (“kNIfe SeTTING BAR”) fIGuRe G kNIfe (16) ReAR TABle (3) cuTTeR HeAD ASSy. (8) for technical questions, please call 1-800-444-3353. SKU 32966 Page 13...
  • Page 14 Fence is 90 degrees to the Front Table (2) and Rear Table (3). If an adjustment is necessary: Loosen the Screw (48). feNce SeGMeNT (39) feNce BODy (4) ScReW (48) TIlT ANGle ScAle (41) MAcHINe ScReW (50) HANDle (72) fIGuRe H for technical questions, please call 1-800-444-3353. SKU 32966 Page 14...
  • Page 15 After the cut is underway, the new surface of the workpiece rests firmly on the Rear Table (3). The right hand pushes the workpiece forward, but before the left hand for technical questions, please call 1-800-444-3353. SKU 32966 Page 15...
  • Page 16 The ridge left by the Cutter Head Assembly (8) when starting the taper may be removed by taking a very light cut according to the regular method for jointing, with the Front Table (2) raised to its usual position. for technical questions, please call 1-800-444-3353. SKU 32966 Page 16...

  • Page 17: Inspection, Maintenance, And Cleaning

    Cuts not smooth. Feeding too fast. Slow feed speed. Working against the grain. Work with grain whenever possible. Cutting too deep on one pass. Take several passes on very deep cuts. for technical questions, please call 1-800-444-3353. SKU 32966 Page 17...
  • Page 18 Spring Knob Screw (M6X12) Retainer Ring Screw(M8X12) Screw Lock Washer (#8) Depth Indicator Nut (M8) Rivet Machine Screw (M10) Nut (M6) Lock Washer (#10) Adjusting Screw (M6X25) Spanner Lock Piece Handle for technical questions, please call 1-800-444-3353. SKU 32966 Page 18...
  • Page 19 Brought To You By Augusta Flint ASSeMBly DIAGRAM - RABBeTING JOINTeR for technical questions, please call 1-800-444-3353. SKU 32966 Page 19...
  • Page 20 Left Tapping Fender Gear Washer (#5) Lock Washer (#8) Nut (M5) Plastic Clip Power Switch V-Belt Pulley Front Side Plate Motor Screw (M8X12) Rear Side Plate Crossbeam Plate Screw (M5X12) Washer (#8) for technical questions, please call 1-800-444-3353. SKU 32966 Page 20...
  • Page 21 Brought To You By Augusta Flint ASSeMBly DIAGRAM - STAND & MOTOR 5A, 6A, 9A, 30A 9A, 10A 11A, 12A, for technical questions, please call 1-800-444-3353. SKU 32966 Page 21...

  • Page 22: Limited 1 Year / 90 Day Warranty

    BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. for technical questions, please call 1-800-444-3353. SKU 32966 Page 22...

Table of Contents