AMX Modero X Series Quick Start Manual

MXA-FMK-10
The MXA-FMK-10 Flush Mount Kit (FG5968-70) allows the Modero X Series
10.1" Wall Mount Touch Panels to be installed nearly flush with the wall. Once
installed, simply press lightly on the black border area on both sides of the touch
panel, and the spring-loaded mechanism switches the panel between the flush
position or slightly extended from the wall surface. The extended position gives
access to the panel's Sleep/Setup button, as well as for enhanced speaker and
microphone exposure. The MXA-FMK-10 is compatible with all Modero X Series
10.1" Wall Mount Touch Panels, including the MXD-1001-P (FG5968-48),
MXD-1001-L (FG5968-49), MXD-1000-P (FG5968-07), MXD-1000-L
(FG5968-13), MXD-1000-P-NC (FG5968-25), and MXD-1000-L-NC
(FG5968-26)
10.63" (27.00 cm)
Landscape
FIG. 1 MXA-FMK-10, Landscape and Portrait Installations
Product Specifications
Dimensions (HWD): 7.43" x 10.63" x 3.64" (18.87 cm x 27.00 cm x 9.25 cm)
Weight: 1.35 lbs (0.61 kg)
Included Accessories: • MXA-FMK-10 Quick Start Guide (93-5968-70)
• MXA-FMK-10 Cutout Template (68-5968-07)
Other AMX • MXD-1001-P 10.1" Modero X® Series G5 Wall Mount
Equipment: Touch Panel, Portrait (FG5968-48)
• MXD-1001-L 10.1" Modero X® Series G5 Wall Mount
Touch Panel, Landscape (FG5968-49)
• MXD-1000-P 10.1" Modero X® Series Wall Mount Touch
Panel, Portrait (FG5968-07)
• MXD-1000-L 10.1" Modero X® Series Wall Mount Touch
Panel, Landscape (FG5968-13)
• MXD-1000-P-NC 10.1" Modero X® Series Wall/Flush
Mount Touch Panel (no Microphone), Portrait
(FG5968-25)
• MXD-1000-L-NC 10.1" Modero X® Series Wall/Flush
Mount Touch Panel (no Microphone), Landscape
(FG5968-26)
• Refer to the 95-5968-70 diagram for detailed installation dimensions.
Pre-Wall Installation of the Flush Mount Kit
The MXA-FMK-10 Flush Mount Kit (FIG. 1) is designed to attach the panel to
most standard wall and solid surface materials. This Flush Mount Kit has four
locking tabs (landscape: two on top and two on bottom; portrait: two on each
side) to help lock the Flush Mount Kit to the wall. These locking tabs are only
extended AFTER the Flush Mount Kit is inserted into the wall. Using the locking
tabs is highly recommended for standard mounting surfaces such as walls.
WARNING: When installing the Flush Mount Kit, make sure that the assembly is
in the correct position and in the correct place. Once the locking tabs are
extended and locked into place, removing the Flush Mount Kit may be difficult
without having access to the back of the wall or causing damage to the wall.
Note: In order to guarantee a stable installation of the MXA-FMK-10, the
thickness of the wall material must be a minimum of .50 inches (1.27cm) and a
maximum of .875 inches (2.22cm). The surface should also be smooth and flat.
WARNING: The maximum recommended torque to screw in the locking tabs on
the plastic Flush Mount Kit is 5 IN-LB [56 N-CM]. Applying excessive torque
while tightening the tab screws, such as with powered screwdrivers, can strip
out the locking tabs or damage the plastic.
MXA-FMK-10
1.
CAUTION: The cutout dimensions shown will allow the unit to pass through
without any dragging or interference. The outer phantom lines show the
perimeter of the mounting flange. If any part of the cutout extends up to or
beyond that perimeter, the cut edge will be visible after installation, or the unit
could fall through the opening. A larger cutout reduces the available surface to
support the unit when mounted, so the cut should be as close to the indicated
dimensions as possible. If the cutout is too small, forcing the unit into place
could result in mechanical binding, faulty operation, or damage to the product.
Always check for a proper fit before final installation.
(17.83 cm)
7.43" (18.87 cm)
Portrait
FIG. 2
2.
FIG. 3
3.
4.
5.
6.
Note: Do not disconnect the connectors from the touch panel. The unit must be
installed with the attached connectors before being inserted into the drywall.
7.
Quick Start Guide
Modero X Series
After ensuring proper placement, cut out the mounting surface, using the
MXA-FMK-10 Cutout Template (68-5968-07) as a guide (FIG. 2).
(25.97 cm)
7.02"
MXA-FMK-10 Cutout Template
Remove the knockout at the top of the Flush Mount Kit (FIG. 3) and thread
the incoming wiring through a knockout hole. The MXA-FMK-10 has two
knockout holes, at the top of the device (Landscape) or to the left (Portrait).
Knockout
MXA-FMK-10
Inserting the MXA-FMK-10 into the wall surface (Landscape)
Thread the incoming Ethernet wiring from their terminal locations through
the surface opening and through the knockout.
Push the Flush Mount Kit flat into the mounting surface and secure with the
locking tabs (FIG. 4). In order to prevent damage to the touch panel, make
sure that any screws used are flush with the Flush Mount Kit, and the
Flush Mount Kit goes freely into the opening.
Insert each connector into its corresponding location along the back of the
touch panel. For more information, please refer to the Quick Start Guide for
the panel being installed.
Test the incoming wiring by attaching the panel connections to their
terminal locations and applying power. Verify that the panel is receiving
power and functioning properly to prevent repetition of the installation.
Latch the panel onto the top hooks on the Flush Mount Kit and rotate it
down (Landscape) onto the bottom snaps or on the left side and rotate it to
the right (Portrait installation). Press gently but firmly and evenly on the
®
Flush Mount Kit
10.22"
Perimeter
of Flush
Mount Kit
flange
Wall Surface
Locking Tab