Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Pro-face PL-X900 Series
Summary of Contents for Pro-face PL-X900 Series
- Page 1 PL-X900 Series Standard Display PL-DU6900/PL-DU7900 User Manual...
-
Page 2: Preface
Preface Preface Thank you for purchasing Digital’s PL-DU6900/PL-DU7900 Series Standard Display (hereafter referred to as "the DU"). The DU unit uses the most up-to-date, cost-effective, high-performance architec- ture and is designed exclusively for use with Digital’s BOX-Type Industrial Computers (hereafter referred to as "the PL"). Please read this manual carefully as it explains, step by step, how to use the DU correctly and safely. -
Page 3: Essential Safety Precautions
Preface Essential Safety Precautions This manual includes procedures that must be followed to operate the DU cor- rectly and safely. Be sure to read this manual and any related materials thoroughly to understand the correct operation and functions of this unit. Icon Meaning Throughout this manual, the following icons are provided next to operations requiring special attention to allow you to use the DU safely. - Page 4 Preface • After the PL’s backlight burns out, unlike the PL’s “Standby Mode”, the touch panel is still active. If the op- erator fails to notice that the backlight is burned out and touches the panel, a potentially dangerous machine miss- operation can occur.
- Page 5 Preface CAUTIONS • When the surface or the frame of the display becomes dirty, soak a soft cloth in water with a neutral detergent, wring the cloth tightly, and wipe the display. Do not use paint thinner, organic solvents, or a strong acid com- pound to clean the unit.
-
Page 6: General Safety Precautions
Preface General Safety Precautions LCD Usage and Handling • The brightness of the LCD screen will depend on the screen's current display and the LCD's contrast adjustment. Any brightness variations that result are normal for LCD displays. • There are minute grid-points (Dark or Light points) on the LCD surface. These points are not defects and are a part of the DU panel’s design. -
Page 7: Table Of Contents
Preface Table of Contents Preface ......................1 Essential Safety Precautions ............... 2 General Safety Precautions ................. 5 Prior to Using the DU ................... 5 Table of Contents ..................6 PL Model Number ..................8 Documentation Conventions ............... 8 Special Features .................... 9 Package Contents .................. - Page 8 Preface CHAPTER 3 OPTIONAL UNITS 3.1 Installation ................... 3-1 3.1.1 Attaching the Display Expansion Board (PL-PE200) ..3-2 3.1.2 Installing the USB Front Access Unit (PL-US200) ..3-5 CHAPTER 4 INSTALLATION AND WIRING 4.1 DU Installation Cautions ..............4-1 4.1.1 Temperature Related Cautions ........... 4-1 4.1.2 Installation Positioning Cautions ........
-
Page 9: Pl Model Number
PL-DU * 900 - T4 2 E F G Item Code Meaning PL Series Industrial Computer PL-X900 Series Display Unit 12.1 inch SVGA 15 inch XGA X900 Series TFT Color LCD CE Marked, UL/c-UL(CSA) Approved Revision No. -
Page 10: Special Features
Preface Special Features The PL-DU*900’s special features are as follows. PL-DU6900 - 12.1" High-Brightness Color Display and Wide View Angle The PL-DU6900’s large 12.1 inch, 800 X 600 pixel TFT LCD display offers excellent visibility and brightness. Digital’s top of the line TFT color LCD model allows you to create detailed and pow- erful visual images, with excellent brightness, a wide viewing angle, and a display capable of 260,000 colors. -
Page 11: Package Contents
AC100V/ (PL-DU6900 8/set) AC115V use. Be sure to (PL-DU7900 12/set use a different cable when using other than AC100V/ AC115V power. PL-X900 SERIES PL-X900 SERIES STANDARD DISPLAY STANDARD DISPLAY PL-DU6900/PL-DU7900 PL-DU6900/PL-DU7900 USER MANUAL : USER MANUAL :... -
Page 12: Ce Marking Notes
Preface UL/c-UL(CSA) Application Notes The PL-DU*900-T4* is a UL/c-UL(CSA)1950 recognized product. (UL File No. E171486). Machinery which has a DU installed in it requires UL/c-UL inspection for the combination of this unit and the machinery. This unit conforms as a component to the following standards: UL 1950, Third Edition, dated 1998 March 1st. - Page 13 Preface • When connecting the DU's power cord, be sure to use a cord that is appropriate for the current and voltage used (0.75mm or larger). • When installing the DU to a metal panel or cabinet, be sure to design the DU's power cut-off switch as a separate device that is within easy reach by the unit's operator.
-
Page 14: Chapter 1 Introduction
1. System Design 2. Accessories Chapter Introduction System Design USB Front Screen Access Unit Protection Sheet (PL-US200) (PL-CS100) <DU> Display Expansion Board Display Unit's Reset (PL-PE200) Button TFT Color LCD Touch Panel Connection Cable (PL-CB200-10M) (PL-CB200-5M)*1 <PL> PL-B900/PL-B910 Series Unit Optional Unit Cable Connection Included in... -
Page 15: Rs-422 And Usb Connections
Chapter 1 - Introduction 1.1.1 RS-422 and USB Connections You canconnect a touch panel using either a RS-422 or a USB cable. The RS-422 and USB cables have limitations concerning the PL type, OS type and number of DU units. Touch Panle Cable PL Type OS Type... -
Page 16: Connecting The Dual Displays
Chapter 1 - Introduction 1.1.2 Connecting the Dual Displays When a USB cable is used, up to 2 DU units can be connected to a single PL unit. Connecting two displays requires two of the optional display cables (PL-CB200- 5M) and one Display Expansion Board (PL-PE200). Use the following explana- tions when connecting the DUs and the Display Expansion Board. - Page 17 Chapter 1 - Introduction When attaching the Dual Displays, be sure of the following points. - The PL unit is a PL-B910 series unit (PL-B910 or PL-B911). - The Touch Panel connection cable should be a USB cable. - The operating system is Windows 98 Second Edition. - Set the PL and DU's dip switch to the USB Cable Settongs.
-
Page 18: Accessories
Chapter 1 - Introduction Accessories All accessories listed below are produced by the Digital Electronics Corporation. Attachment Units Product Name Model No. Description Display Expansion PL-PE200 Allows you to connect 2 DUs to a PL. Board USB Front Access PL-US200 Allows you to connect other USB equipped Unit units to the DU from the front of the DU. - Page 19 Chapter 1 - Introduction Commercially Available Items The PL-B910 Series units can use USB compatible devices. However, among the commercially available USB devices, not all will be compatible with the PL unit. For a list of the USB units that can be used with your PL, please contact your local PL distributor.
-
Page 20: Chapter 2 Specifications
1. General Specifications 4. Display Unit Dimensions Chapter 2. Functional Specifications 3. Names and Functions of DU Parts Specifications General Specifications 2.1.1 Electrical AC100V to AC240V Input Voltage AC85V to AC265V Rated Voltage Rated Frequency 50Hz or 60Hz 1 cycle or less Allowable Voltage Drop (Actual drop can be more than 1 second) 50VA or less... -
Page 21: Structural
Chapter 2 - Specifications 2.1.3 Structural PL-DU6900 PL-DU7900 Equivalent to IP65f (JEM1030) (front face only - when installed in panel) Ratings Unit Composition: Single Unit Type Installation Method: In a solid panel Cooling Natural air circulation Method 5.5 Kg (12.1lb) or less 7.0 Kg (15.4lb) or less Weight 346mm (13.62in.) <W>... -
Page 22: Functional Specifications
Chapter 2 - Specifications Functional Specifications 2.2.1 Performance PL-DU6900 PL-DU7900 SVGA (800 X 600 dots) XGA (1024 X 768 dots) Graphics 16 colors/ 256 colors/ 32k colors/ 64k colors VESA 12.1 inch T FT SVGA 15.0 inch T FT XGA Display Unit Resisive Film (Analog ) Type... -
Page 23: Names And Functions Of Du Parts
Chapter 2 - Specifications Names and Functions of DU Parts A: Display Area Display output area. B:Touch Panel A high resolution analog type touch panel. Allows you to create your control systems without using a key board. C:Status LED The status of the lamp changes according to the alarm type detected by the RAS feature. -
Page 24: Display Unit Dimensions
Chapter 2 - Specifications Display Unit Dimensions 2.4.1 PL-DU6900 External Dimensions Unit: mm <in.> (Main Unit Only) Top View 330 <12.99> Side View Front View 63 <2.48> 346 <13.62> 14 <0.55> 31 <1.22> 2.4.2 PL-DU7900 External Dimensions Unit: mm <in.> (Main Unit Only) Top View 359 <14.13>... -
Page 25: Pl-Du6900 Installation Fasteners
2.4.3 PL-DU6900 Installation Fasteners Unit: mm <in.> <13.03 > • Be sure the thickness of the panel is from 1.6mm (0.06in.) to 10mm (0.39 in.) • Depending on material used for panel surface, you may need to strengthen the panel surface. Especially, if high levels of vibration are expected and the DU’s installation surface (i.e. -
Page 26: Chapter 3 Optional Units
1. Installation Chapter Optional Units Installation The following explanation pages describe the installation procedures for the Display Expansion Board (PL-PE200) and the USB Front Access Unit (PL-US200). For information about the installation of other option units, please refer to those unit’s individual [Operation Instructions]. -
Page 27: Attaching The Display Expansion Board (Pl-Pe200)
Chapter 3 - Optional Units 3.1.1 Attaching the Display Expansion Board (PL-PE200) In this explanation, drawings for the PL-DU7900-T42 drawings are used. Disconnect the DU power cord terminals from the DU's power terminal block. Be sure to place the Remove Power Terminals DU unit on a flat, lever surface prior to install-... - Page 28 Chapter 3 - Optional Units Fig. A Rear Cover Remove the Rear Cover and expose the interior of the DU Front Panel (see Fig. Fig. B Loosen the Side Cover’s screw, and push the Front Panel’s Slide in the direction shown to release it.
- Page 29 Chapter 3 - Optional Units Cover A Unscrew the three (3) Cover A Attachment Screws and remove Cover A (see figure.) After inserting the PL- PE200, check that the PL Rear Part and the PL-PE200 connec- tors are correctly aligned, Attachment insert the PL-PE200’s three Screws...
-
Page 30: Installing The Usb Front Access Unit (Pl-Us200)
Chapter 3 - Optional Units 3.1.2 Installing the USB Front Access Unit (PL-US200) Use the following procedure to install the PL-US200 in the DU. Unscrew the blank panel’s three (3) attachment screws and remove the DU rear face’s PL-US200 blank panel. - Page 31 Chapter 3 - Optional Units Insert the PL-US200 into the PL and secure it in place with two (2) attachment screws. Attachment Screws Socket Insert the PL-US200’s USB Connector into the DU’s USB Socket. Connector Insert the PL-US200 cable’s black Rubber Stopper in the DU rear panel’s notch.
-
Page 32: Chapter 4 Installation And Wiring
1. DU Installation Cautions Chapter 2. DU Installation 3. Wiring Cautions Installation and Wiring DU Installation Cautions 4.1.1 Temperature Related Cautions Be sure to confirm that the area near the DU will be within the allowable temperature range by 100mm placing a temperature sensor in the location shown in the left-side Front face... -
Page 33: Du Installation
Chapter 4 - Installation and Wiring DU Installation 4.2.1 Installation Confirm the Installation Gasket’s Seating It is strongly recommended that you use the gasket. Place the DU on a level surface with the display panel facing downward. Check that the DU’s installation gasket is seated securely into the gasket’s groove, which runs around the perimeter of the panel’s frame. - Page 34 Chapter 4 - Installation and Wiring DU Viewing Angle • The DU must be installed vertically. Also, the DU uses a cooling fan. To operate the DU correctly, be sure that the panel’s viewing angle is tilted no more than 30 de- grees from parallel to the operator (i.e.
- Page 35 Chapter 4 - Installation and Wiring Securing the Installation Fasteners 1) There are eight (8) insertion slots on the top and bottom of the PL-DU6900, and twelve (12) insertion slots on the top and bottom of the PL-DU7900 where the metal installation fasteners hook on. Attachment Hole Top/Bottom View PL-DU7900...
-
Page 36: Wiring Cautions
Chapter 4 - Installation and Wiring Wiring Cautions 4.3.1 Connecting to PL After connecting the DU to the PL-B900 Series unit and setting up the PL's OS, you will need to complete the DU's screen settings and touch panel calibration. For details, refer to BOX-Type Industrial Computer PL-B900/ B910 Series Users Manual. - Page 37 Chapter 4 - Installation and Wiring 2) Loosen and remove the middle three screws Black from the terminal strip. Align the crimp terminals with each screw hole, and tighten the White screws. • Crimp Terminal Types : V1.25-3, by J.S.T. or equivalent (JIS stan- Green/Yellow dard part number : RAV1.25-3) •...
-
Page 38: Connecting The Du's Power Supply
Chapter 4 - Installation and Wiring 4.3.3 Connecting the DU’s Power Supply Be sure to follow cautions explained here when connecting the power cord to the DU’s Power Input Terminals. Twisted-pair • If voltage fluctuations are expected to cable Constant vary beyond the specified range, connect voltage transformer... -
Page 39: Grounding The Du
Chapter 4 - Installation and Wiring 4.3.4 Grounding the DU (a) Dedicated Ground - best • Set up a dedicated ground when using the rear panel’s FG terminal. Other device • If a dedicated ground is not possible, use a (b) Shared Ground - allowed shared ground, as shown in figure (b). -
Page 40: Chapter 5 Maintenance
1. Regular Cleaning Chapter 2. Changing the Backlight 3. Periodic Check Points Maintenance Regular Cleaning 5.1.1 Cleaning the Display When the surface or the frame of the display gets dirty, soak a soft cloth in water with a neutral detergent, wring the cloth tightly, and wipe the display. •... -
Page 41: Changing The Backlight
Chapter 5 - Maintenance Changing the Backlight The DU's backlight can be replaced after it has burned out. To replace the back- light, follow the steps shown below. Please use the following table to identify which backlight model number to use when ordering your backlight. - Page 42 Chapter 5 - Maintenance • Be sure to replace the back- light on a flat, level surface. This will prevent damage to the DU unit and the acciden- tal cutting of any of its power cord terminals. • The PL-DU7900 has a cover. When replacing the PL- DU7900's backlight, you Cover...
- Page 43 Chapter 5 - Maintenance When Changing the PL-DU6900 Backlight Disconnect both Board Backlight backlight power connectors from the board. Power Connectors Backlight Each backlight (upper Board and lower) is fixed in place with two (2) attachment screws. Power Remove these 4 Connector screws.
- Page 44 Chapter 5 - Maintenance Open/release each plastic cable holder. Each backlight uses a cable holder to prevent the cable from becoming caught or pinched when the DU’s rear cover is opened or closed. Be sure both cables are se- cured by their holder before closing the rear cover.
- Page 45 Chapter 5 - Maintenance Remove each backlight unit. Insert each new back- light. Be sure to hold the new backlights with the metal clips. After installing both new backlights using steps 9) to 10), replace and tighten all attachment screws (total of 4 screws).
- Page 46 Chapter 5 - Maintenance When Changing the PL-B7900 Backlight The DU’s LCD display Attachment Screws unit is fixed in place with two (2) attachment screws. Remove these screws. Disconnect both back- light power connectors from the Invertor Board. Each backlight (upper and lower) is fixed in place with an attachment screw.
- Page 47 Chapter 5 - Maintenance Remove each backlight unit. Insert each new backlight. After installing both new backlights using steps 9) to 11), replace and tighten all backlight and LCD panel attachment screws (total of 4 screws). Then, re-connect both board power connectors. •...
-
Page 48: Periodic Check Points
Chapter 5 - Maintenance Periodic Check Points To keep your DU unit in good working condition, please check the following points periodically. DU Operation Environment • Is the operating temperature within the allowable range? • Is the operating humidity within the specified range (30% RH to 85% RH)? •... - Page 49 Memo...
-
Page 50: Index
Index Index About PL-DU*900 Models ........8 Icon Meaning ............2 Accessories ............1-5 Insert the DU into the Installation Slot ....4-3 Installation ............. 3-1 Installation and Wiring .......... 4-1 Installation Cautions ..........4-1 backlight type ............5-2 Installation Gasket ..........4-2 Brightness Adjustment Slide ......... - Page 51 Index Power Input Terminals .......... 4-5 Power Switch ............2-4 Power Terminals ............ 2-4 Preface ..............1 Prior to Using the DU ..........5 Regular Cleaning ........... 5-1 Securing the Installation Fasteners ......4-4 Shock / Vibration Related Cautions ...... 4-1 Specifications ............