All-in-one console extender dual video, amplified or line-level audio, rs-232, and 3 separate usb extensions: two direct plus one with 4-port hub to 150 meters (500 ft) (20 pages)
Fiber optic video extender extend hdmi/dvi or vga/ypbpr together with full-duplex rs-232 over a single fiber optic cable (24 pages)
Summary of Contents for Hall Research Technologies VERSA-4K Series
Page 1
User’s Manual VERSA-4K AV Over IP 4K Video Over IP USB 2.0 Over IP + Keyboard & Mouse Bidirectional Audio, RS232 & IR Passthrough Dynamic Virtual Matrix™ Part Number Function VERSA-4K-S Encoder/Sender VERSA-4K-R Decoder/Receiver UMA1283- Rev CUSTOMER Order toll-free in the U.S. 800-959-6439 SUPPORT FREE technical support: 714-641-6607 or support@hallresearch.com INFORMATION...
VERSA-4K Table of Contents Introduction ............................5 Application ............................5 Package Contents ..........................6 Accessories............................6 Input and Outputs ..........................7 Getting Started ............................ 8 Control Interface ..........................9 Front Panel Operation ........................ 9 IR Remote Controller ....................... 10 IR Detectors and Emitters ....................10 WEB-GUI ............................
Page 3
VERSA-4K Bezel and Gap Compensation ..................18 OSD ..............................18 OSD Settings ........................... 18 Audio Over IP ..........................19 Audio Modes ........................... 20 USB Over IP ..........................20 USB Settings ..........................21 Keyboard and Mouse ....................... 21 Serial Over IP ..........................22 RS-232 Modes ........................
Page 4
VERSA-4K FCC Notice This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference even if it causes undesired operation. This equipment has been desinged to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
VERSA-4K Introduction VERSA-4K is a complete AV over IP solution, which can extend 4K video with one frame latency, four USB 2.0 Devices with additional Key board and mouse, Bidirectional IR, Full Duplex RS-232, and Bidirectional analog audio, all in 1G Ethernet Network. VERSA uses visually lossless compression and has inbuilt Video Scaler and Video Wall support, which makes it one stop scalable solution for the today's AV needs Specifications...
VERSA-4K Input and Outputs Fig 2: VERSA-4K-S Front and Rear panel Fig 3: VERSA-4K-S Front and Rear panel Front Panel USB Mini for Front Panel Firmware update MENU, UP, User Buttons for front panel operation DOWN Factory Reset 16x2 Character display for System Configuration Rear 1000BT RJ45 Jack -- Connects to 1G Ethernet...
VERSA-4K Getting Started Use Gigabit Switch with IGMPV2 and Jumbo Frame Support Connect Sender(s) and Receiver(s) to the switch. No DHCP server required, by default Auto IP is enabled. If switch does not support PoE, use external power supply include in the package Assign unique Group ID...
VERSA-4K Control Interface Front Panel Operation VERSA features a 16X2 Character LCD and with three user buttons: MENU, UP and DOWN on the front panel, which allows the user to quickly change the Group ID and IP configuration. By default, VERSA displays Device Name and Group ID on the Home Screen, UP and DOWN arrow keys can be used change the Group ID.
VERSA-4K SUBNET Subnet Mask GATEWAY Gateway BAUD RS-232 Baud Rate USB 2.0 (Receiver Only) Used to the Connect/Disconnect with Sender in the same group Status Name Description MAC ADD Mac Address of the Device USB RX IP (Sender Only) Shows the IP address of the Receiver to which USB is connected USB TX IP (Receiver Only) Shows the IP address of the Sender to which USB...
VERSA-4K IR Detector cable for Local Control . Connected to "IR-CTRL" port of VERSA IR Emitter cable for Passthrough. Connected to "IR-OUT" port of VERSA WEB-GUI VERSA hosts a WEB Application with intuitive Graphical User Interface (GUI) , which can be accessed using any standard WEB browser.
VERSA-4K Fig 7: VERSA-4K-R WEB -GUI PC-GUI PC-GUI is used to configure all the advanced settings, such as Filtering, OSD, EDID Management, SOIP, and Bezel and Width Compensation. With advanced device finder, PC-GUI gives an advanced top level management interface to control all the VERSAs on the network.
VERSA-4K Working Architecture VERSA uses Client-Server architecture, where each function such as Video, Audio, USB, IR, RS-232 is considered as a service. VERSA-4K-S (Sender) being a server, provides services independently under one Group ID. Each VERSA-4K-R (Receiver) in the network acts a client and receives a service by joining in the group using Group A Receiver should have the same Group ID as sender to receive a service.
VERSA-4K General Settings Device Name User can assign Device Name to VERSA, which can be used to identify its Location or Purpose. Device Names are useful for Logical representation of the system in big installations and they are not linked to IP address. For instance, all the Receivers connected to the projectors in a school can have Room Number as Device Name.
VERSA-4K Fig 10. Independent Routing Note that, Audio only works when there is a active Video Group. Video Over IP VERSA-4K-S uses visually lossless compression to encode 4K Video. Along with bit rate and Frame rate adjustments, Sender provides Various Quality modes and Bit Rate adjustments to minimize the network bandwidth.
VERSA-4K multicast mode, a receiver in the group can send an EDID Update Request to replace Custom EIDD with its attached Sink EDID. A Receiver automatically sends an Update Request when Display is detected, if "Use this EDID" option is enabled. When multiple receivers sends an EDID update request, the last received request will be successful.
Page 17
VERSA-4K Fig 10. Video Wall Layout For example, to build a 2x2 (two by two) Video Wall, which has 2 rows and 2 columns. So, Horizontal Monitor Count [X] = 2, Vertical monitor Count [Y] =2 A total of 4 Receivers are required to build this wall and they can be positioned at: (0,0) , (0,1) , (1,0), and (1,1) Each Receiver includes a Video Wall Preview in its WEB-GUI, which helps to visualize the wall.
VERSA-4K Video Wall Settings Wall Size [X,Y] X = [1 to 16] Horizontal Monitor Count Y = [1 to 16] Vertical Monitor Count Set [1,1] to disable Video Wall Position (x',y') x' =[0 to 15] Horizontal Position y' =[0 to 15] Vertical Position Orientation Default Flip Vertical/Horizontal (Mirror Image)
VERSA-4K Text Color RGB: [x,y,z] Character Count Text Pixel Size [1 to 100] Text Align Center/Left OSD Alpha Blend (31 is no [1 to 31] transparency) OSD Background Mask ON/OFF Timer (In Seconds) Always ON/ [0 to 100] Image Size 640x480 Type JPEG /PNG 32bpp...
VERSA-4K Fig 12. Audio Modes Audio Modes Input Mode Auto Auto Select LINE IN when Input is DVI or when (Only for Sender) LINE IN hot plug is detected Auto 1 Auto Select LINE IN when Line hot plug is detected Auto 2 Always use HDMI audio when video Input is not Always use LINE IN when video Input is DVI...
VERSA-4K Fig 13. USB2.0 Export Policy USB Settings VERSA-4K-S Attached Client IP IP Address for connected Receiver (Sender) Auto Connect to USB will be automatically connected the first First Peer receiver seen in the group (Useful when there is only one receiver in the group) USB Incompatibility Enable when the mouse is responding slow VERSA-4K-R...
VERSA-4K Serial Over IP Both Sender and Receiver supports two types of modes to control RS-232 devices. In Pass Through mode, all the bytes from the senders are multicast to all the receivers in the group, like wise all the bytes from the receiver is directed to the sender in the group. The Guest mode allows 3rd party control systems to control serial devices over IP.
VERSA-4K Default Configuration Settings Name Value Network Casting Mode Multicast IP Mode Auto IP Jumbo Frame 8000 MTU 169.254.xxx.xxx Subnet 255.255.0.0 Gateway 169.254.0.254 System Device Name VERSA Group ID 0000 Independent Routing Disabled Encoder Settings Bit Rate Best Effort (VERSA-4K-S Frame Rate 100% Only)
VERSA-4K Firmware Update Steps to update firmware from WEB-GUI: Accesses the Sender or Receiver WEB-GUI Navigate to Admin > Update Firmware Click on Choose File and Select the Binary File (.bin) provided by Hall Research. Click Upload Wait until the System finishes the Firmware Update and Reboots itself.
VERSA-4K Specifications System Supports Device Naming, IP Control Build in WEB Server with Institutive User Interface Front panel with 16x2 Character display for System configuration IR Remote Control Sender Supports Independent routing Receiver Built OSD generator, which can display custom text and pictures Built in Scalar with can support: low resolution <=>...
Page 27
VERSA-4K Audio Over IP Sender Analog Audio Line In, Line Out for Audio Over IP Supports HDMI Audio Embedding Receiver Analog Audio Mic In, Line Out for Audio Over IP Supports HDMI Audio De-Embedding Supports Analog Volume Control Bidirectional Audio extension in Unicast mode USB Over IP USB Extension up to 4xUSB 2.0 Downstream Devices...
VERSA-4K HDMI Audio Format Support List Dolby Linear PCM Dolby Digital 5.1 DTS 5.1 ch Linear PCM 2 ch 44.1 kHz Dolby Digital DTS 96/24 Linear PCM 2 ch 88.2 kHz Plus Dolby Digital DTS-ES Discrete Linear PCM 2 ch 176.4 kHz Pro-Logic Dolby TrueHD DTS-ES Matrix...