Superabrasive
PREPARATION FOR WORK
Make sure that: You have closed
the work area, so that no persons unfamiliar with operating the
machine can enter the area. The tool plate and tools are
adjusted to the machine properly. There are no missing parts of
the machine. The machine is in upright working position. The
protection devices are working properly. The electrical cable is
free to move and follow the machine easily. In order to keep the
electrical cable from being damaged, no vehicle should cross the
zone where electrical cables are situated.
PROTECTION DEVICES
The machine is equipped with several protection devices
including the following:
An emergency stop button
A protection skirt and a hood for protecting the tool
plates.
These devices protect the operator and/or other persons from
potential injuries. Do not remove them. On contrary, before
using the machine, please ensure that all protective devices are
mounted and function properly. The security plate prevents the
QuickChange pads from loosening during work.
ARREST FUNCTIONS
Functions of arresting of the machine are following:
Button to s top the mo tor (category 1)
Emergency button (category 1)
SAFE USE
The Lavina®25LM‐S‐E is designed to eliminate all risks correlated
with its use. However, it is not possible to eliminate the risks of
eventual accident with the machine. Unskilled or uninstructed
operator may cause correlated residual risks.
Such risks are:
Position Risks due to operator's incorrect working position
Tangling up Risks due to wearing inappropriate working clothes
Training Risks due to lack of operational training
NOTE: In order to reduce all consequences of the above‐
mentioned risks, we advise that ma chi ne operator's follow the
instructions in the manual at all times.
RESIDUAL RISKS
During the normal operating and maintenance cycles, the
operator is exposed to few residual risks, which cannot be
eliminated due to the nature of the operations.
BEFORE YOU BEGIN
Working area must be clear from any debris or objects.
A first‐time operator must always read the manual and pay
attention to all safety instructions.
All electric connections and cables must be inspected for
potential damages.
Ground wire system of the power supply must also be inspected.
Perform general daily inspections of the machine and inspect the
machine before each use.
Always inspect the safety devices: Mount the security plate and
the QuickChange pads
The emergency break must be clear and working.
The tool protector must be working
User Manual
Original Language
The machine must be clean
Never operate the machine in the rain!
Confirm that there are no missing parts especially after
transportation, repair, or maintenance.
Before filling the water tank with water make sure that the
machine is not working and the main switch is turned off.
Before turning on the machine make sure that the base is
Placed on the floor, the machine MUST NOT be in an upright
position when turned on!
OPERATING MACHINE
When operating the Lavina®25LM‐S‐E , make certain that there
is no
one, but you around the machine.
Never leave the machine unattended while working.
The electrical cable must move freely and must be damage‐
free.
The water hose must move freely and must be damage‐free.
Check if the floor, you will work on, is not too uneven. If this is
the
case, it may cause damage to the machine.
After Work is completed
Clean the machine and its surroundings properly
Empty and clean the water tank
Unplug the ma chi ne and wind up the electrical cable
Store the machine in a safe place
THE WORK AREA
Make certain that people or vehicles do not enter the work
area.
Avoid cables and hoses being in the way.
Always check the floor for debris.
PERSONAL PROTECTIVE
EQUIPMENT (PPE)
Always wear safety shoes when working with the machine.
Always wear protectors when working with the machine.
All personnel in the immediate work area must wear safety
glasses with side shields.
Always wear safety gloves when changing the tools.
Always wear clothes suitable for the work environment.
OPERATOR
The Lavina®25LM‐S‐E machine.
The operator must know the machine's work environment.
Only one operator at a time can work with the machine. The
operator must be properly trained and well instructed prior
to operating the machine.
The operator must understand all the instructions in this
manual.
The operator must understand and interpret all the drawings and
designs in the manual.
The operator must know all sanitation and safety regulations
pertaining to the operation of the Lavina 25LM‐S.
The operator must have floor grinding experience.
The operator must know what to do in case of an emergency.
The operator must have an adequate technical knowledge and
preparation.
5
Lavina® 25LM‐S‐E
12/2014