Fleck 5600 Installation Instructions Manual page 8

IIm mg g 5 5 -- T To op p D Diis st tr riib bu ut to or r B Ba as sk ke et t
I I m m g g 6 6 . Please note that locking tabs hold it in place so a fair amount of force is needed to install or
remove it.
3 3 . . 3 3 — — S S c c r r e e w w o o n n c c o o n n t t r r o o l l h h e e a a d d
* * ! ! * * D D O O N N O O T T a a p p p p l l y y a a n n y y t t h h i i n n g g ( ( p p i i p p e e d d o o p p e e , , p p l l u u m m b b e e r r s s p p a a s s t t e e , , T T e e fl flo o n n t t a a p p e e , , e e t t c c . . ) ) t t o o t t h h e e t t h h r r e e a a d d s s o o n n t t h h e e
c c o o n n t t r r o o l l h h e e a a d d o o r r t t h h e e r r e e s s i i n n t t a a n n k k ! ! * * ! ! * *
Ensure the riser tube slips inside the pilot opening in the bottom of the head. Screw the head down
onto the resin tank until solid contact is made between the tank and O-ring, then tighten about another
1/4–1/3 of a turn and STOP.
Once properly tightened down check to ensure the tank and control head meet evenly all the way
around.
4 4 — — P P
R R E E P P A A R R E E A A N N D D
4 4 . . 1 1 — — A A s s s s e e m m b b l l e e t t h h e e b b r r i i n n e e t t a a n n k k
IIm mg g 7 7 -- U Un na as ss se em mb blle ed d B Br riin ne e T Ta an nk k
Depending on system
configuration your system may
include a top distributor
basket—I I m m g g 5 5 . If your system
includes one it is recommended
that you use it. If you do not
have one then it is not needed. If
you do have one the larger end
will fit inside the bottom of your
control valve, with the smaller
end sliding over the riser tube
pointing down into the tank—
* * ! ! * * h h a a n n d d t t i i g g h h t t o o n n l l y y * * ! ! * *
* * * * D D o o n n o o t t o o v v e e r r t t i i g g h h t t e e n n t t h h e e c c o o n n t t r r o o l l h h e e a a d d a a s s t t h h i i s s c c a a n n c c a a u u s s e e d d a a m m a a g g e e . . * * * *
C C B B
O O N N N N E E C C T T R R I I N N E E
The brine tank will come with
the brine well loose, either
inside the brine tank or in the
box with the brine tank—I I m m g g 7 7 .
You will use the overflow fitting
to attach it in the side of the
brine tank, placing the overflow
fitting through the lower hole on
the brine tank and securing it
through the brine well with the
nut—I I m m g g 8 8 . If you are having a
hard time fitting your hand
T T
A A N N K K
8 of 19
IIm mg g 6 6 -- A At tt ta ac ch he ed d T To op p D Diis st tr riib bu ut to or r B Ba as sk ke et t
IIm mg g 8 8 -- A As ss se em mb blle ed d B Br riin ne e T Ta an nk k