Fleck 5600 Installation Instructions Manual page 17

Open a nearby faucet. The water may be discolored at first, this is normal. Let water run out of the
faucet for at least 10 minutes, or until any discoloration clears up. Depending on the system this may be
almost immediate, or it may take a couple of hours. Once the water is cleared up a manual regeneration
should be run.
7 7 . . 4 4 — — I I n n i i t t i i a a t t e e m m a a n n u u a a l l r r e e g g e e n n e e r r a a t t i i o o n n
It is a good idea to allow the system to run through a manual cycle. On mechanical valves, turn the main
knob until it clicks into the first position. On digital systems, hold the extra cycle button for 5-10 second
until the backwash starts.
7 7 . . 5 5 — — V V e e r r i i f f y y p p r r o o p p e e r r o o p p e e r r a a t t i i o o n n
Watch the system as it steps through each cycle, make sure it moves to each position, that water is not
leaking from any other fittings, and that water is flowing down the drain line. The brine line will have
water flowing through it during the appropriate cycles as well.
empty the system will not draw water out of the brine tank during the brine draw cycle. This cycle can
be skipped during the initial startup by pressing the extra cycle button after the [ [ B B D D ] ] cycle has started
counting down. The resin is precharged and the brine water is not needed for the first cycle, the initial
cycle is run to ensure the brine tank has the correct amount of water for the first automatic cycle.
* * * * B B e e s s u u r r e e t t o o r r e e t t u u r r n n a a n n y y o o t t h h e e r r s s y y s s t t e e m m s s t t o o t t h h e e s s e e r r v v i i c c e e p p o o s s i i t t i i o o n n . . * * * *
F F r r e e q q u u e e n n t t l l y y A A s s k k e e d d Q Q u u e e s s t t i i o o n n s s
I I
N N V V E E N N T T O O R R Y Y A A N N D D
W W h h a a t t i i s s t t h h e e p p r r o o p p e e r r o o r r d d e e r r t t o o a a r r r r a a n n g g e e m m u u l l t t i i p p l l e e s s y y s s t t e e m m s s ? ?
If you are installing more than one tank system the typical order for installation is:
* * * * s s e e d d i i m m e e n n t t fi fil l t t e e r r > > p p H H fi fil l t t e e r r > > i i r r o o n n fi fil l t t e e r r > > c c a a r r b b o o n n fi fil l t t e e r r > > w w a a t t e e r r s s o o f f t t e e n n e e r r > > a a r r s s e e n n i i c c fi fil l t t e e r r * * * *
Whole house cartridge systems are typically installed after any tank systems, the Scale Sentry system
after the cartridge system(s), and any UV systems will be last.
D D o o I I n n e e e e d d a a p p r r e e fi fil l t t e e r r ? ?
In most cases a prefilter is not necessary. Since the system cleans itself most particulate in the water will
be trapped and rinsed off by the regeneration cycle, eliminating the need for a sediment prefilter. If you
have a lot of sand in the water a spin down filter (part #SDF-100) is recommended to protect the control
head. For water supplies with high levels of chlorine a carbon prefilter is recommended to extend resin
life.
M M y y p p o o l l y y g g l l a a s s s s t t a a n n k k a a r r r r i i v v e e d d a a n n d d s s i i t t s s c c r r o o o o k k e e d d , , w w h h a a t t d d o o I I d d o o ? ?
S S
E E T T U U P P
* * * * P P l l e e a a s s e e N N o o t t e e : : * * * *
17 of 19
With the brine tank