List Of Components; Installation; Manual Operation - Chicco Dream Cradle Instructions For Use Manual

The equipment works together with the Bluetooth® Low-
Energy standard.
• Frequency ranges: 2.400 - 2.4835 GHZ;
• Channels: 79 channels, each with a band width of 2 MHz; ;
• Transmission power: - 5 dBm (transmitted to the antenna);
• Standard Radio: 802.15.1
THIS PRODUCT COMPLIES WITH THE DIREC-
TIVE 2012/19/EU.
The crossed bin symbol on the appliance in-
dicates that the product, at the end of its life,
must be disposed of separately from domestic waste,
either by taking it to a separate waste disposal site for
electric and electronic appliances or by returning it to
your dealer when you buy another similar appliance. The
user is responsible for taking the appliance to a special
waste disposal site at the end of its life. If the unwant-
ed appliance is collected correctly as separate waste, it
can be recycled, treated and disposed of ecologically;
this avoids a negative impact on both the environment
and health, and contributes towards the recycling of the
product's materials.

LIST OF COMPONENTS

- Button A (A)
- Button B (B)
- Carrycot fastening rings (C)
- Switch (D)
- Power adapter socket (E)
- Power adapter (F)

INSTALLATION

1. Place The Dream Cradle on a flat surface (Fig. 1).
2. Connect the transformerto your mains network by plug-
ging the power adaptor into The Dream Cradle (Fig. 2).
3. Place the LIGHTNAP carry cot (of the LOVE UP and STYLEGO
UP strollers) on The Dream Cradle taking care to orient it so
that the child' s head is in the direction of the power switch
and of The Dream Cradle transformer power adapter sock-
et until you hear the click on both sides (Fig. 3). To facilitate
installation on the platform, it is possible to pull the release
lever of the carry cot positioned in the test area (Fig. 3A).
WARNING: Before using, make sure that the carry cot is
properly attached to The Dream Cradle by pulling it up-
wards (Fig. 3B).
4. Turn on the power/switch (Fig. 4).

MANUAL OPERATION

The Dream Cradle offers the possibility of selecting three
different operating programmes.
- PROGRAMME 1: SPORT (continuous movement)
- PROGRAMME 2: OFF ROAD (After three cycles of continu-
ous movement, the programme stops for three seconds
in the central position, then restarts and repeats the se-
quence)
- PROGRAMME 3: URBAN (After a continuous movement
cycle, the programme stops for a second in the central
position, then restarts and repeats the sequence)
5. To select the programme, press the CONTROL button
(Fig. 5) until the desired programme is reached. Pressing
the button a fourth time will restart the cycle from PRO-
GRAMME 1.
The Dream Cradle, with one of the selected programmes,
operates for 30 minutes from the selection of the desired
programme at the end of which The Dream Cradle will
automatically return to the stop position. However, you
can stop the selected programme 30 minutes before, by
pressing and holding the control button for two seconds.
At power on, or after the shut-down procedure, the first
programme that can be selected is PROGRAMME 1.
When the programme is turned off, The Dream Cradle con-
tinues to move until it reaches the horizontal position. The
signal that the programme has been deactivated is com-
municated when the LED changes from green to red.
WARNING: Never unplug the power cord or press the
switch while The Dream Cradle is running to prevent it from
stopping in a non-horizontal position (Fig. 6).
If The Dream Cradle is stopped without correctly deactivat-
ing the programme, it is necessary to perform realignment
by reconnecting it to the mains power, switching it on and
restarting any programme in order to proceed to correct-
ly power it off (press and hold button "A" for at least two
seconds).
OPERATING The Dream Cradle VIA THE APPLICATION
You can use The Dream Cradle by connecting it to your
smartphone via Bluetooth® by downloading the "The
Dream Cradle" application.
Downloading the application
Download and install The Dream Cradle application availa-
ble on and
Associating your smartphone with The Dream Cradle
To pair your smartphone with The Dream Cradle, you need
to turn on Bluetooth® on your smartphone and open The
Dream Cradle application.
After opening the application, a red circle will be shown on
the Bluetooth® button. To perform the pairing procedure,
press the button until it switches from solid red to flashing
yellow. Subsequently, press and hold the Bluetooth button
of The Dream Cradle until the blue led switches from flash-
ing to solid (Fig. 7).
After the connection is established, the led of The Dream
Cradle will be lit and at the same time the circle on the Blue-
tooth® button of the application will become solid green.
N.B.: The Bluetooth button of The Dream Cradle will be
enabled only if the application is open and the Bluetooth®
connection on your smartphone is active.
You can now operate The Dream Cradle by clicking on the
desired programme icon. (Fig. 8)
The Dream Cradle, with one of the selected programmes,
operates for 30 minutes from the selection of the desired
programme at the end of which The Dream Cradle will au-
tomatically return to the stop position.
If you wish to change the programme, simply press the
icon of the programme you want to operate on your smart-
phone.
However, you can stop the selected programme before 30
minutes by pressing the STOP icon (Fig. 9). The LED located
next to the control button A will change from green to red
and The Dream Cradle will stop when it reaches the hori-
zontal stop position.
To activate The Dream Cradle again, simply click on the de-
sired programme icon.
Using several devices
The Dream Cradle saves the last three associated devices,
9
.