Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Fleck Manuals
  4. Water Dispenser
  5. 7000
  6. Installation manual

Fleck 7000 Installation Manual

Hide thumbs Also See for 7000:

Advertisement

Quick Links

Download this manual See also: Service Manual
This material is intended only for Glass Water Systems customers. Reproduction or
distribution of this material is strictly prohibited and protected. For further questions contact
Glass Water Systems or their Attorney, Kenneth L. Olsen (813) 223-3657. Glass Water
Systems is not liable for any damage caused by your installation. This is strictly a guide for
our valued Customers.
INSTALLING 7000
1

Advertisement

loading

Related Manuals for Fleck 7000

Summary of Contents for Fleck 7000

  • Page 1 For further questions contact Glass Water Systems or their Attorney, Kenneth L. Olsen (813) 223-3657. Glass Water Systems is not liable for any damage caused by your installation. This is strictly a guide for our valued Customers. INSTALLING 7000...
  • Page 2 15. Teflon Tape If you have additional items you would recommend If you have additional items you would recommend please call us –improvement and customer please call us –improvement and customer satisfaction is our goal. satisfaction is our goal. INSTALLING 7000...
  • Page 3 32K Unit = 1 Cu Ft Bag 40K Unit = 1-1/4 Cu Ft Bag 48K Unit = 1-1/2 Cu Ft Bag 64K Unit = 2 Cu Ft Bag Gravel (Optional) Fleck 7000 Control Valve Bypass Installation Fitting Assemblies 1” NPT 1-1/4” NPT 1-1/4”...
  • Page 4 You can either use a sink, an outside drain, or dig a hole approximately 24-36” and fill with rock The hole needs to be about 12-18” in diameter Water meter Usually homes have A main shut off with a Ball valve or a Gate Valve INSTALLING 7000...
  • Page 5 Take the Valve and screw back on the tank –be careful not to cross-thread the tank. We usually go backwards until it locks in and then tighten it down. After you have the valve on take it and place it where you want it. INSTALLING 7000...
  • Page 6 The brass connection fitting that has to be sweat or glued is item 1 in both drawing below. Once you have done this you will follow the procedures on installing the fitting adapters. These are items a and b. INSTALLING 7000...
  • Page 7 14. With the valve In Service, check that there is at least 1" of water above the grid in the brine tank, if used. 15. Fill the brine tank with salt. 16. Allow the control to run automatically. Setup is now complete. INSTALLING 7000...

  • Page 8: Check For Leaks

    Once you have done that follow the instruction on page 17 –19 for setting up the valve. After doing the instructions go ahead and hit regenerate and let the water softener completely go through all the cycles. Please call us with any questions 1-877-345-2770 INSTALLING 7000...
  • Page 9 INSTALLING 7000...
  • Page 10 Volume Remaining display in gallons or liters. The Meter dot flashes in direct relation to the water flow rate through the unit. As treated water is used, the Volume Remaining display counts down from a maximum value to zero and initiates a Regeneration cycle. INSTALLING 7000...
  • Page 11 • Upon power re-application, resumes normal operation from the point that it was interrupted. • Does not monitor the volume of water used during a power outage. • In Delay Regeneration types, the reserve capacity is set to 1/3 the capacity. INSTALLING 7000...
  • Page 12 INSTALLING 7000...
  • Page 13 INSTALLING 7000...
  • Page 14 INSTALLING 7000...
  • Page 15 INSTALLING 7000...
  • Page 16 INSTALLING 7000...
  • Page 17 INSTALLING 7000...
  • Page 18 INSTALLING 7000...
  • Page 19 INSTALLING 7000...
  • Page 20 INSTALLING 7000...
  • Page 21 INSTALLING 7000...
  • Page 22 INSTALLING 7000...
  • Page 23 INSTALLING 7000...