Download Print this page
Panduit PANZONE PZWIFIEW Installation Instructions Manual
Panduit PANZONE PZWIFIEW Installation Instructions Manual

Panduit PANZONE PZWIFIEW Installation Instructions Manual

Wireless access point enclosure

Advertisement

Quick Links

© Panduit Corp. 2005
Hardware Guide
#10-32
#10
#8-32
#8
Keyed Knockout
Slots for Wall
Mount Application
(6 places)
(door removed from view for clarity)
TABLE OF CONTENTS
External Wall Mount Installation........................................................................................ 2-4
In-Ceiling Mount Installation.............................................................................................. 5-7
For Technical Support: www.panduit.com/resources/install_maintain.asp
P
INSTALLATION INSTRUCTIONS
List of Components:
(4) #10-32 Hex Nuts
(4) #10 Split Lock Washers
(4) #8-32 Hex Nuts
(4) #8 Split Lock Washers
(1) Grounding Cable
(4) Pieces of Fire Resistant Foam
(1) 26" length Grommet Edging
(1) 2 Position Surface Mount Box
(PANDUIT Part No. CBXJ2WH-A)
(1) 2' long Cat5e Patch Cord
(PANDUIT Part No. UTPCH2)
(1) Cat5e Jack Module
(PANDUIT Part No. CJ5E88TWH)
(1) Foam Retention Plate
(1) Key
Brackets for Fire
Resistant Foam
(2 places)
Double Knockout
for 1/2" or 3/4"
Conduit (3 places)
Z
Wireless Access Point Enclosure
AN
ONE
Part Number: PZWIFIEW
PZWIFIEW
Knockouts
for Surface
Raceway
(2 places)
Page 1 of 8
CM310
#10-32 threaded
Grounding Studs
Page (s)

Advertisement

loading

Summary of Contents for Panduit PANZONE PZWIFIEW

  • Page 1 Wireless Access Point Enclosure Part Number: PZWIFIEW INSTALLATION INSTRUCTIONS CM310 © Panduit Corp. 2005 Hardware Guide List of Components: (4) #10-32 Hex Nuts (4) #10 Split Lock Washers (4) #8-32 Hex Nuts (4) #8 Split Lock Washers (1) Grounding Cable...
  • Page 2 1/2” or 3/4” conduit. For Surface Raceway - Remove knockout “D” or “E”. This opening accommodates PANDUIT LD10 surface raceway. 1.2 Locate the wall studs. Position the enclosure on the wall and identify which keyed knockouts should be removed. It is recommended that two of the mounting holes be aligned with the wall stud.
  • Page 3 Step 6: Install Surface Mount Box 6.1 Run the network cable to and into the enclosure. 6.2 Terminate the Cat5e Jack Module to the network cable. Refer to the PANDUIT website for jack termination instructions if needed. 6 / 7 6.3 Mount the base of the 2 Position Surface Mount Box to...
  • Page 4 Please read these instructions in their entirety prior to installing the enclosure. Note: PANDUIT Part Number PZWIFIDCB is required for the in-ceiling mount application. Step 1: Knockout Removal 1.1 Remove knockouts in desired cable entry location:...
  • Page 5 INSTALLATION INSTRUCTIONS CM310 Step 3: Install Ceiling Mount Brackets PANDUIT Part #: PZWIFICB - PanZone Wireless Access Point Ceiling Bracket Kit (sold separately) 3.1 Install Ceiling Mount Brackets against side wall of the enclosure with the flanged edge facing away from the enclosure.
  • Page 6: Installation Instructions

    Cat5e jack cannot be removed through a 1/2” conduit knockout. 8.2 Terminate the Cat5e Jack Module to the network cable. Refer to the PANDUIT website for jack termination instructions if needed. 8.3 Mount the base of the 2 Position Surface Mount Box to the back wall of the enclosure using provided double sided tape.
  • Page 7 10.1 Insert one end of the 2' long Cat5e Patch Cord into the RJ45 port located on the WAP. 10.2 Insert the other end of the patch cord into the Cat5e jack located in the surface mount box. Surface Mount For Technical Support: www.panduit.com/resources/install_maintain.asp Page 7 of 8...
  • Page 8 Designed for Cisco Aironet™ 1200 Series (excludes Cisco Aironet™ 1232AP) PZWIFIED PZWIFIED with PZWIFIDCB Designed for Cisco Aironet™ 1232AP PZWIFIEW PZWIFIEW with PZWIFICB Designed for Cisco Aironet™ 1130 series APs E-mail: For Instructions in Local Languages cs@panduit.com and Technical Support: Fax: www.panduit.com/resources/install_maintain.asp www.panduit.com (708) 444-6448 Page 8 of 8...