Advertisement
Quick Links
© Panduit Corp. 2008
List of Common Components:
Hardware Guide
Hardware Guide
#10-32
#10
#8-32
#8
#6-32 Screws
#10-32 Screws
Keyed Knockout
Slots for Wall
Mount applications
(6 places)
Brackets for
Fire Resistant Foam (2 places)
(door removed from view for clarity)
TABLE OF CONTENTS
Wall Mount Installation..................................................................................................................................................... 2
Ceiling Mount Installation..................................................................................................................................................2-4
Cisco Aironet 1250 Series Access Point Installation........................................................................................................ 5
Cable Routing....................................................................................................................................................................6
Alternate Wall Mount Installation with External Mount Antennas.......................................................................................7
Alternate In-Ceiling Installation with External Mount Antennas..........................................................................................8
FOR TECHNICAL SUPPORT www.panduit.com/resources/install_maintain.asp
P
AN
Part Numbers: PZWIFIEN, PZWIFIENS
INSTRUCTIONS CM365
(4)#10-32 Hex Nuts
(4)#10 Split Lock Washers
(4)#8-32 Hex Nuts
(4)#8 Split Lock Washers
(2)#6-32 Screws
(1)Grounding Cable
(4)Pieces of Fire Resistant Foam
(1)26" length Grommet Edging
(1)2 Position Surface Mount Box
(PANDUIT Part No. CBXJ2WH-A)
PZWIFIEN ONLY
(1)2' long Category TX6 Plus Patch Cord
(PANDUIT Part No. UTPSP2)
(1)Category TX6 Plus Jack Module
(PANDUIT Part No. CJ688TGWH)
Double Knockout
for 1/2" or 3/4" Conduit
(3 places)
RP-TNC
Wall Mount
bulkhead
connector
knockout
(6 places)
Knockout for
electrical
junction box
Z
Wireless Access Point Enclosure
ONE
(2)P
-T
mounts
AN
Y
(PANDUIT Part No. ABMM-A-C)
(4)P
-T
Cable Ties
AN
Y
(PANDUIT Part No. PLT1.5I-C)
(1)Foam Retention Plate
(2)Keys
(2) Latching Wire Clips
(Panduit Part No. LWC50-A-L)
(4) # 10-32 X 3/8" Thread Cutting
Screws
PZWIFIENS ONLY
(1) Minicom TX6 plus shielded jack
(CJS666TGY)
(1) 1M STP TX6 plus patch cord
(STP6X1MBU)
Knockouts for
Knockouts
led lights
for Surface
on the wap
Raceway
(2 places)
#10-32
Threaded
Grounding
Studs
Page 1 of 8
PZWIFIEN
RP-TNC Ceiling Mount
bulkhead connector
knockout (6 places)
Antenna knockouts for
6 internal antenna
mounting applications
Page (s)
Advertisement
Related Manuals for Panduit PZWIFIEN
Summary of Contents for Panduit PZWIFIEN
- Page 1 Wireless Access Point Enclosure Part Numbers: PZWIFIEN, PZWIFIENS INSTRUCTIONS CM365 © Panduit Corp. 2008 List of Common Components: Hardware Guide Hardware Guide PZWIFIEN (2)P mounts (4)#10-32 Hex Nuts (4)#10 Split Lock Washers (PANDUIT Part No. ABMM-A-C) (4)#8-32 Hex Nuts (4)P...
-
Page 2: Wall Mount Installation
Please read these instructions in their entirety prior to installing the enclosure. Note: P Enclosures Require one of the following additional part numbers for in-ceiling applications PANDUIT Part #:PZWIFIDCB - P Wireless Access PANDUIT Part #:PZW2X2DCB - P Wireless Access Point Point In-Ceiling Bracket Kit In-Ceiling 2’x 2’... - Page 3 Hinge 4.2 Secure the four sides of the enclosure to the bracket with (4) #6-32 screws provided with the bracket as shown. Hinge Slot For Technical Support: www.panduit.com/resources/install_maintain.asp Page 3 of 8...
- Page 4 (on top of TGB cable) Studs and the other end to the grounding stud on the door. 6.3 Secure with the #10 Split Lock Washers and #10-32 Hex Nuts. For Technical Support: www.panduit.com/resources/install_maintain.asp Page 4 of 8...
- Page 5 Mount bracket supplied To release depress with the access point lever and slide AP towards hinge side of enclosure #10-32 Screws Wall Mount Dipole Ceiling Mount Dipole Antenna Configuration Antenna Configuration For Technical Support: www.panduit.com/resources/install_maintain.asp Page 5 of 8...
- Page 6 8.1 Run the network cable to and into the enclosure. 8.2 Terminate the TX6 PLUS Jack Module to the network cable. Refer to the PANDUIT web site for jack termination instructions if needed. 8.3 Mount the base of the 2 Position Surface Mount Box to the back wall of the enclosure using provided double sided tape.
- Page 7 RP-TNC Knockouts #6-32 Screws “Short” flange (opposite side) (External Antenna Applications) “Long” flange (STD) (Dipole Antenna Applications) Reverse plate 180° Mount Plate Figure 1.1 RP-TNC Knockouts Figure 1.4 Figure 1.2 Figure 1.3 For Technical Support: www.panduit.com/resources/install_maintain.asp Page 7 of 8...
- Page 8 Knockouts “Long” flange (STD) (Dipole Antenna Applications) Reverse plate 180° RP-TNC Mount Plate Figure 2.1 Knockouts Figure 2.4 Figure 2.2 Figure 2.3 For instuctions in Local Languages E-mail: and Technical Support: cs@panduit.com Fax: www.panduit.com/resources/install_maintain.asp (708)444-6448 www.panduit.com Page 8 of 8...