Winmate R19L300-SDA1 User Manual

Winmate R19L300-SDA1 User Manual

Sdi display, 10.1-32”

Advertisement

SDI Display
10.1~32"
User Manual
Version 1.0
Document Part No.: 915211101040
Please read this instructions before operating the device and retain them for future reference.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the R19L300-SDA1 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Winmate R19L300-SDA1

  • Page 1 SDI Display 10.1~32” User Manual Version 1.0 Document Part No.: 915211101040 Please read this instructions before operating the device and retain them for future reference.
  • Page 2: Table Of Contents

    10.1~32" SDI Display User Manual Contents Preface About This User Manual ..................... 6 Chapter 1: Introduction 1.1 Overview ......................8 1.2 Product Features ....................8 1.3 Package Contents ....................8 1.4 Product Overview ....................9 1.5 Interfaces ......................10 1.6 OSD Control Panel ..................... 11 1.7 OSD Hot Keys ....................
  • Page 3: Preface

    Preface Preface Copyright Notice No part of this document may be reproduced, copied, translated, or transmitted in any form or by any means, electronic or mechanical, for any purpose, without the prior written permission of the original manufacturer. Trademark Acknowledgement Brand and product names are trademarks or registered trademarks of their respective owners.
  • Page 4 10.1~32" SDI Display User Manual Naming Rule R10LXXX-SDXX Item Description Panel Type Panel Size LXXX Product Size Mechanical Type (SDI) Panel Model Advisory Conventions Four types of advisories are used throughout the user manual to provide helpful information or to alert you to the potential for hardware damage or personal injury.
  • Page 5 Preface Safety Information Warning!/ Avertissement! Always completely disconnect the power cord from your chassis whenever you work with the hardware. Do not make connections while the power is on. Sensitive electronic components can be damaged by sudden power surges. Only experienced electronics personnel should open the PC chassis.
  • Page 6: About This User Manual

    Do not cover the openings! About This User Manual This User Manual provides information about using the Winmate® SDI Display. The documentation set provides information for specific user needs, and includes:  SDI Display User Manual – contains detailed description on how to use the display, its components and features.
  • Page 7: Chapter 1: Introduction

    Chapter 1: Introduction Chapter 1: Introduction This chapter gives you product overview, describes features and hardware specification. You will find all accessories that come with the display device in the packing list. Mechanical dimensions and drawings included in this chapter.
  • Page 8: Overview

    Part No. 947018102000 **Notice: Screw bolts provided by Winmate only to be used to screw the display onto a console from the rear side. If you prefer your own bolts, please make sure to use M4 and 30mm in length.
  • Page 9: Product Overview

    Chapter 1: Introduction 1.4 Product Overview This section describes physical appearance of the SDI Display. Note: Notice that standard input terminals include VGA and HDMI. Your device may be equipped with DVI, S-Video or Composite input terminals based on your order. Notice that input and output connectors vary by product size and specifications.
  • Page 10: Interfaces

    W10L100-SDH2 263.6 x 172.3 x 38.5 75 x 75 15” R15L100-SDA3 350.2 x 274.2 x 38.5 100 x 100 19” R19L300-SDA1 438.7 x 363.5 x 38.9 100 x 100 21.5” W22L100-SDA3 518.1 x 314 x 38.5 100 x 100 32”...
  • Page 11: Osd Control Panel

    Chapter 1: Introduction 1.6 OSD Control Panel OSD control panel varies by product specifications. Physical buttons and LED indicators are located on the OSD control panel the rear side of the display. Control Buttons Function POWER - Initiates power-up sequence from low power mode or enters low power mode from normal operation.
  • Page 12: Chapter 2: Installation

    10.1~32" SDI Display User Manual Chapter 2: Installation This chapter provides hardware installation instructions and mounting guide for all available mounting options. Pay attention to cautions and warning to avoid any damages...
  • Page 13: Wiring Requirements

    Chapter 2: Installation 2.1 Wiring Requirements The following common safety precautions should be observed before installing any electronic device:  Strive to use separate, non-intersecting paths to route power and networking wires. If power wiring and device wiring paths must cross make sure the wires are perpendicular at the intersection point.
  • Page 14: Mounting Guide

    SDI Display comes with VESA Mount holes for mounting. Installation Instruction: 1. Screw VESA bracket to the fixture (ex. swing arm) with four VESA screws. 2. Place the device on VESA bracket. Notice that VESA stand and mounting kit are not provided by Winmate.
  • Page 15: Connecting Peripherals

    Chapter 2: Installation 2.5 Connecting Peripherals The panel control port is designed for monitors that work with a variety of compatible video sources. Due to the possible deviations between these signal sources, you may have to make adjustments to the monitor settings from the OSD menu when switching between these sources. Note: Notice that standard input terminals include VGA and HDMI.
  • Page 16: Sdi Output Connector

    10.1~32" SDI Display User Manual 2.5.3 3G-SDI Output Connector Pin assignment and signal names of 3G-SDI output connector Pin № Signal Name SDI_OUTPUT 2.5.4 3G-SDI Input Connector Pin assignment and signal names of 3G-SDI input connector Pin № Signal Name SDI_INPUT 2.5.5 CVBS Connector Pin assignment and signal names of CVBS connector...
  • Page 17: Turning On The System

    Chapter 2: Installation 3.1 Turning on the System To turn on the system: 1. Connect the power adapter cable to the DC IN of the display. 2. Connect the power cord to the power adapter. 3. Connect the power cord to a power outlet. 4.
  • Page 18: Chapter 3: Operating The Device

    10.1~32" SDI Display User Manual Chapter 3: Operating the Device In this chapter you will find instructions on how to operate the display.
  • Page 19: Osd Menu Navigation

    Chapter 3: Operating the Device 3.2 OSD Menu Navigation OSD Icon Sub-menu Settings Note BRIGHTNESS slider bar Default 50 Use to adjust the screen’s brightness. Range 0 to 100 CONTRAST slider bar Default 50 Use to adjust the screen’s contrast. Range 0 to 100 SHARPNESS slider bar Default 50...
  • Page 20 10.1~32" SDI Display User Manual OSD Icon Sub-menu Settings Note OSD TURN OFF slider bar Default 10 Turns off the OSD after a period of inactivity. The preset choices are 0-60 seconds. H POSITION slider bar OSD POSITION Default 50 V POSITION slider bar Determines the location where the OSD appears on the screen.
  • Page 21: Troubleshooting Guide

    Chapter 3: Operating the Device 3.3 Troubleshooting Guide If your monitor fails to operate correctly, check the following chart for possible solution before calling for repairs: Condition Check Point • Check if the signal cable is firmly seated in the socket. The picture does not •...
  • Page 22: Appendix

    10.1~32" SDI Display User Manual Appendix This chapter contains additional product information, including troubleshooting guide and frequency table...
  • Page 23: Appendix A: Frequency Table

    Appendix Appendix A: Frequency Table The choice of supported modes depends on the monitor native resolution. Separate RGB Video Signal (VGA) Input Timing Resolution Frequency (Hz) Note 640x480 640x480 VESA 640x480 VESA 640x480 VESA 720x400 800x600 VESA 800x600 VESA 800x600 VESA 800x600 VESA...
  • Page 24 Winmate Inc. 9F, No.111-6, Shing-De Rd., San-Chung District, New Taipei City 24158, Taiwan, R.O.C www.winmate.com Copyright © Winmate Inc. All rights reserved.

This manual is also suitable for:

R15l100-sda3W10l100-sdh2W22l100-sda3W32l100-sda

Table of Contents