Table of Contents
Advertisement
Quick Links
Flat PCAP Display
Document Version 1.3
Document Part No. 91521110100N
Please read these instructions carefully before using this product, and save this manual for future use
IP65 Stainless
10.4"/ 15"/ 17"/ 19"/ 21.5"/ 23.8"
Quick Start Guide
Model No. R10L100-SPT2
R15L100-SPC3
R17L100-SPA1
R19L100-SPM1
W22L100-SPA3
W24L100-SPA2
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Winmate W24L100-SPA2
Summary of Contents for Winmate W24L100-SPA2
- Page 1 10.4”/ 15”/ 17”/ 19”/ 21.5”/ 23.8” Model No. R10L100-SPT2 R15L100-SPC3 R17L100-SPA1 R19L100-SPM1 W22L100-SPA3 W24L100-SPA2 Quick Start Guide Document Version 1.3 Document Part No. 91521110100N Please read these instructions carefully before using this product, and save this manual for future use...
-
Page 2: Table Of Contents
IP65 Flat Stainless P-Cap Display Contents Introduction Features Package Contents Product Overview Dimensions 10.4" Dimensions 15" Dimensions 17” Dimensions 19” Dimensions 21.5” Dimensions 23.8” Physical Buttons and LED Indicators Connectors Getting Started Turning On Your Device Turning Off Your Device Installation Wiring Requirements Connector Pin Assignments... - Page 3 Introduction FCC Statement This device complies with part 15 FCC rules. Operation is subject to the following two conditions: This device may not cause harmful interference. This device must accept any interference received including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a class "B"...
- Page 4 Brand and product names are trademarks or registered trademarks of their respective owners. Disclaimer Winmate Inc. reserve the right to make changes, without notice, to any product, including circuits and/or software described or contained in this manual in order to improve design and/or performance. We assume no responsibility or liability...
- Page 5 Introduction Customer Service We provide a service guide for any problem by the following steps: First, visit the website of our distributor to find the update information about the product. Second, contact with your distributor, sales representative, or our customer service center for technical support if you need additional assistance.
-
Page 6: Introduction
Projected Capacitive Multi-Touch (P-CAP) screen supports glove mode and provides even more convenience for the operator. Winmate® IP65 Flat Stainless P-CAP Display goes beyond that of the standard industrial panel computers with elegant, edge-to-edge design, rugged construction, powerful performance, and flexible mounting options. -
Page 7: Package Contents
Introduction Package Contents Carefully remove the box and unpack your device. Please check if all the items listed below are inside your package. If any of these items are missing or damaged contact us immediately. Standard factory shipment list may include the following items: Quick Start Guide R-series AD Board Display... -
Page 8: Product Overview
IP65 Flat Stainless P-Cap Display Product Overview This section contains mechanical drawing of the Display. Notice that this is a simplified drawing and some components are not marked in detail. Dimensions 10.4" Unit: mm Dimensions 15" Unit: mm... -
Page 9: Dimensions 17
Introduction Dimensions 17” Unit: mm Dimensions 19” Unit: mm... -
Page 10: Dimensions 21.5
IP65 Flat Stainless P-Cap Display Dimensions 21.5” Unit: mm Dimensions 23.8” Unit: mm... -
Page 11: Physical Buttons And Led Indicators
Introduction Physical Buttons and LED Indicators Physical buttons and LED indicators located on the rear side of the Display. Physical Buttons Icon Button Description DOWN/ Press to decrease the volume or volume VOLUME down when without OSD menu DOWN UP/ VOLUME Press to increase the value or volume up when without OSD menu Press to exit the menu or auto adjustment... -
Page 12: Connectors
IP65 Flat Stainless P-Cap Display LED Indicators LED Type Status Description Power is on Power is off System is in standby mode System is idle Connectors IP69K Flat Stainless P-Cap Display has waterproof M25 type connectors with protection cap. IMPORTANT: To maintain the IP69K rating of the full unit it is recommended to use only IP69K waterproof cables. -
Page 13: Getting Started
Getting Started Getting Started Turning On Your Device Follow the following steps to turn on your device: 1. Connect the AC adapter (12V/50W) to the DC power connector located on the back side of the display. 2. Connect the power cord to AC adapter. 3. -
Page 14: Installation
IP65 Flat Stainless P-Cap Display Installation Wiring Requirements The following common safety precautions should be observed before installing any electronic device: • Strive to use separate, non-intersecting paths to route power and networking wires. If power wiring and device wiring paths must cross make sure the wires are perpendicular at the intersection point. -
Page 15: Connector Pin Assignments
Installation Connector Pin Assignments This Display is equipped with four connectors which are IP65 level and fool- proofing design. Use only the cables that are included in the package. The pin assignments of the cables are as follows. Power Cable The Flat Stainless P-CAP Display has IP65 power connector. -
Page 16: Usb Cable (For Touch)
IP65 Flat Stainless P-Cap Display USB Cable (For Touch) The Flat Stainless P-CAP Display has IP65 USB connector for touch. Use USB cable to connect touch. VGA Cable The Flat Stainless P-CAP Display has IP65 VGA connector. Use VGA cable to connect the display to other external devices. -
Page 17: Dvi Cable (Optional)
Installation DVI Cable (Optional) The Flat Stainless P-CAP Display has optional IP65 DVI connector. Use DVI cable to connect the Display to other external device. -
Page 18: Mounting
VESA Mounting The Display has VESA mount holes on the rear side. Follow instructions below to mount the unit with VESA Mount bracket (not supplied by Winmate). Size VESA Plate Screw Hole... -
Page 19: Yoke Mounting
Installation Yoke Mounting Yoke Mount solution allows installing the Display with the bracket (not supplied by Winmate). Mounting instruction: 1. Place the Display on the bracket stand, aiming screw holes for each other. 2. Secure screws to fix the device upon the bracket stand. -
Page 20: Specifications
IP65 Flat Stainless P-Cap Display Specifications Hardware Specifications Model Name R10L100- R15L100- R17L100- R19L100- W22L100- W24L100- SPT2 SPC3 SPA1 SPM1 SPA3 SPA2 Display Size 10.4” 15” 17” 19” 21.5” 23.8” Resolution 1024 x 768 1024 x 768 1280 x 1024 1280 x 1024 1920 x 1080 1920 x1080... - Page 21 Model Name R10L100- R15L100- R17L100- R19L100- W22L100- W24L100- SPT2 SPC3 SPA1 SPM1 SPA3 SPA2 Power Specifications Power Input 12V DC 12V DC 12V DC 12V DC 12V DC 12V DC VESA VESA Power VESA DPMS VESA DPMS VESA DPMS VESA DPMS DPMS DPMS Management...
-
Page 22: Appendix A: Cleaning The Monitor
IP65 Flat Stainless P-Cap Display Appendix A: Cleaning the Monitor Before cleaning: • Make sure the device is turned off. • Disconnect the power cable from any AC outlet. When cleaning: • Never spray or pour any liquid directly on the screen or case. •... -
Page 23: Appendix B: Available Input Signals
Appendix B: Available Input Signals For information about available input signals, please refer to R-Series AD Board Manual included in the package. You can also download R - Series AD Board Manual from Winmate Download Center. Follow the link below: http://dc.winmate.com.tw/_downloadCenter/2009/Lcd/Display%20RSeries%20U... - Page 24 Winmate Inc. 9F, No.111-6, Shing-De Rd., San-Chung District, New Taipei City 24158, Taiwan, R.O.C www.winmate.com Copyright © Winmate Inc. All rights reserved.
Need help?
Do you have a question about the W24L100-SPA2 and is the answer not in the manual?
Questions and answers