Table of Contents
Advertisement
Quick Links
FM6100 Series Multi-Point Lock
Installation Instructions for
Window Shutter Applications
Recommended Installation:
Install FM6100 so that the
deadbolt is equidistant
from the top and bottom
of the shutter.
A8058:A
4/16/10
Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
FOR ASSISTANCE, CONTACT SARGENT AT 800-727-5477 or www.sargentlock.com
Advertisement
Table of Contents
Related Manuals for Assa Abloy Sargent FM6100 Series
Summary of Contents for Assa Abloy Sargent FM6100 Series
- Page 1 A8058:A 4/16/10 Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited. FOR ASSISTANCE, CONTACT SARGENT AT 800-727-5477 or www.sargentlock.com...
-
Page 2: Table Of Contents
FM6100 Series Multi-Point Lock Table of Contents Installation of Deadbolt Assembly ............3 Installation of Bottom Bolt Assembly . -
Page 3: Installation Of Deadbolt Assembly
FM6100 Series Multi-Point Lock Installation of the Deadbolt Assembly • Place the window shutter on a horizontal surface with the pin lever notch located at the top of the shutter facing up. • The recommended deadbolt assembly location should be equidistant from the top and bottom of the shutter. -
Page 4: Installation Of Top Pusher Assembly
FM6100 Series Multi-Point Lock Installation of the Bottom Bolt Assembly continued • With the Deadbolt Retracted, slide the Bottom Bolt Sub Nylon Guides Assembly into the prep. hole in the bottom of the shutter. As you guide the assembly up into the shutter you will need to guide it into the bottom nylon guide of the Deadbolt Assembly and then up through the top nylon guide. -
Page 5: Aligning Assemblies In Preparation For Drilling And Pinning
FM6100 Series Multi-Point Lock Alignment of components in preparation for drilling and pinning • Thread the Top Bolt Clamp into the threaded hole so that it extends the top latch to the proper position for pinning. The Top Bolt Clamp will assure that the top latch is in the correct position for final installation. - Page 6 FM6100 Series Multi-Point Lock Alignment of components in preparation for drilling and pinning continued Before continuing to the next step be certain the top pusher and bottom bolt are in the correct position. • Bottom Bolt should be flush to the bottom of the shutter.
-
Page 7: Applying The Drill Jig For Proper Drilling
FM6100 Series Multi-Point Lock Applying the drill jig for proper drilling • Manually project the deadbolt by applying force to the deadbolt lever toward the bottom of the shutter. • The deadbolt lever is now in a position to allow the Drill Guide Deadbolt to be positioned above the deadbolt and fixed into position Lever... -
Page 8: Pinning The Rods To Engage The Deadbolt Lever
FM6100 Series Multi-Point Lock Pinning the Rods to engage the Deadbolt Lever Hole shown in proper • Loosen the Drill Guides clamping screw allowing the Drill pinning position. Guide to be removed from the shutter. • Manually retract the Deadbolt by applying force to the deadbolt lever toward the top of the shutter. -
Page 9: Installation Of Cylinder In Outside Trim (Optional)
FM6100 Series Multi-Point Lock Installation of Cylinder in Outside Trim (Optional) • Insert the Cylinder into the Cylinder Collar • Place the Cylinder Retaining Nut against the backplate of the outside trim assembly. • Feed the cylinder and cylinder collar into the cylinder hole of the escutcheon and screw the cylinder retaining nut to the cylinder until it is fully seated with the cam straight up as shown. -
Page 10: Installation Of Deadbolt Strike
FM6100 Series Multi-Point Lock Installation of Deadbolt Strike • Assemble the Deadbolt Strike to the frame using (2) ¼" – 20 by 1" Flat Head Cap Screws. Deadbolt Strike Install the Bottom Strike Bottom Strike • Place the Bottom Strike into the Strike Shim and fasten to the frame using (2) ¼"... - Page 12 The company’s customer base includes commercial construction, institutional, and industrial markets. Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.