Technical Specifications - Metabo KGS 305 Original Operating Instructions

15. Technical Specifications

Voltage
Current draw
Fuse protection
Motor capacity * (power input P1, S6 20% - 5 min)
Protection class
Degree of protection
Saw blade speed
Cutting speed
Saw blade diameter (outer)
Arbor bore
Dimensions
Machine in packing
− Length / width / height
Machine ready to work, rotating table in 90° position, c/w suction port
− Length / width / height
Maximum workpiece cross section
Standard cross cuts
− width / height
Mitre cuts (rotating table 45°)
− width / height
Bevel cuts (track arm holder 45° left)
− width / height
Bevel cuts (track arm holder 45° right)
− width / height
Compound mitre cuts (rotating table 45° / track arm holder 47° left)
− width / height
Weight
− Machine in packing
− Machine ready to work
Permissible ambient temperature for operation
Permissible temperature for transport and storage
Noise emission values according to EN 61029-1 **
− Sound power level L
WA
− Sound pressure level at operator's ear L
− Uncertainty K
Effective value of weighted acceleration (Vibration at handle)
Uncertainty K
Dust collector (not included in standard delivery)
− Diameter of sawhead suction port
− Diameter of suction port at rear of saw
− Minimum air volume flow
− Minimum vacuum at suction port
− Minimum air speed at suction port
* This machine is specially designed for the high momentary loads of crosscutting. The motor reaches the stated power of 2000
watts at S6 20% 5 min. (intermittend periodic duty-type with starting). This means that this saw can be operated for 1 minute at full-
load rating (2000 watts) within a 5 minute operating period. The motor has to deliver these 2000 watts only under extreme load
conditions - during normal crosscutting it is subjected to much lower loads. With lower loads the duty cycle of the motor increases
substancially. Thus, when used as specified, because of its high reserve capacity, overheating or overloading of the motor is not
possible.
** The values stated are emission values and as such do not necessarily constitute values which are safe for the workplace.
Although there is a correlation between emission levels and environmental impact levels, whether further precautions are necessary
cannot be derived from this. Factors influencing the actually present environmental impact level in the workplace include the charac-
teristics of the work area and other noise sources, i.e. the number of machines and other neighbouring work processes. Also, per-
missible workplace values may vary from country to country. This information is intended to assist the user in his estimate of haz-
ards and risks.
PA
V 230 (1∼ 50 Hz)
A 9.4
A 10 (time-lag)
kW 2.0
IP 20
II
-1
min 3800
m/s 61
mm 305
mm 30
mm 905 / 592 / 563
mm 1180 / 1040 / 690
mm 320 / 106
mm 226 / 106
mm 320 / 60
mm 320 / 40
mm 226 / 60
kg 37
kg 31
°C
0 to +40
°C
0 to +40
dB (A) 110
dB (A) 102
dB (A) 4
2
m/s < 2.5
2
m/s 1.5
mm 43
mm 58
3
m /h 460
Pa 530
m/s 20
ENGLISH
110 (1∼ 50 Hz)
15.5
16 (time-lag)
1.55
20
II
3650
61
305
30
905 / 592 / 563
1180 / 1040 / 690
320 / 106
226 / 106
320 / 60
320 / 40
226 / 60
37
31
0 to +40
0 to +40
110
102
4
< 2.5
1.5
43
58
460
530
20
29