Related Manuals for Yeastar Technology Elastix
Summary of Contents for Yeastar Technology Elastix
- Page 1 How to Connect Elastix to NeoGate TA FXS Gateway How to Connect Elastix to NeoGate TA FXS Gateway Version: 1.0 Yeastar Technology Co., Ltd. Date: 2014.06.06 http://www.yeastar.com 1/15...
- Page 2 How to Connect Elastix to NeoGate TA FXS Gateway Table of Contents: 1. Introduction..................3 2. Preparation ..................4 3. VoIP Mode ..................5 4. SPS/SPX Mode ................. 8 http://www.yeastar.com 2/15...
-
Page 3: Introduction
This guide has been tested with NeoGate TA3200 and Elastix firmware version: 2.4.0. Two modes are available for NeoGate TA to connect to Elastix, we call them VoIP trunk mode and Service Provider SIP/IAX trunk mode (SPS/SPX). *You can simply choose one mode to achieve the connection. -
Page 4: Preparation
(e.g., the IP address, subnet mask, default gateway address and DNS address) by default. Before connecting NeoGate TA3200 to Elastix, you need to set a static IP address from the same LAN with the Elastix. Steps to set static IP for NeoGate TA3200: 1. -
Page 5: Voip Mode
How to Connect Elastix to NeoGate TA FXS Gateway 3. VoIP Mode If you choose VoIP mode, the FXS ports will be registered as the Elastix's SIP extensions, whose functions are the same with other SIP extensions on Elastix. Figure 3. Connect TA3200 and Elastix via VoIP Mode Step 1. - Page 6 How to Connect Elastix to NeoGate TA FXS Gateway Path: Gateway→VoIP Settings→VoIP Server Settings Check "Enable Register", fill in the Elastix IP address; this VoIP server template will be a VoIP mode template. Figure 5. Configure the VoIP Server Template as VoIP Mode...
- Page 7 How to Connect Elastix to NeoGate TA FXS Gateway Figure 6. Edit Dial Pattern Template Step 4. Edit the FXS port Path: Gateway→FXS Port List→FXS Port List Figure 7. Edit the FXS Port Primary Server: choose “Elastix(3)”, the VoIP server template configured in Step 2.
-
Page 8: Sps/Spx Mode
Elastix should match the dial pattern, or calls will fail. 4. SPS/SPX Mode If you choose this mode to connect NeoGate TA3200 and Elastix, the FXS port will be registered as a Service Provider SIP/IAX (SPS/SPX) trunk to the Elastix. - Page 9 How to Connect Elastix to NeoGate TA FXS Gateway Step 1. Create a Service Provider SIP Trunk on Elastix Path: PBXTrunksAdd SIP Trunk Figure 10. Add SIP Trunk http://www.yeastar.com 9/15...
- Page 10 How to Connect Elastix to NeoGate TA FXS Gateway Figure 11. Configure SIP Trunk PEER Details: host=192.168.5.13 type=peer qualify=yes disallow=all allow=ulaw,alaw,gsm After creating the SIP trunk, we can check the status of this trunk, it should be Path: PBXTools Enter the command “sip show peers” and click “Execute”, the status will be seen.
- Page 11 Path: Gateway→VoIP Settings→VoIP Server Settings Do not check "Enable Register", choose SIP protocol, and fill in the Elastix IP address, the VoIP server template will be configured as SPS mode. Figure 13. Configure the VoIP Server Template as SPS Mode...
- Page 12 Path: Gateway→FXS Port List→FXS Port List Figure 15. Edit the FXS Port Number: set a number for the FXS port. The number should be different from the extension numbers on Elastix. Here we set number 100 for FXS port 2. http://www.yeastar.com 12/15...
- Page 13 Step 5. Create an inbound route on Elastix. Path: PBX→Inbound Routes→Add Incoming Route Choose the inbound destination as IVR, when you call in Elastix from NeoGate TA3200, you will hear the IVR prompt. The inbound route configured here matches DID number 9999, users from NeoGate TA3200 should dial 9999 to reach Elastix.
- Page 14 How to Connect Elastix to NeoGate TA FXS Gateway Figure 17. Add Incoming Route Step 5. Create one outbound route on Elastix. To make calls from Elastix to NeoGate TA3200, you need to create one http://www.yeastar.com 14/15...
- Page 15 How to Connect Elastix to NeoGate TA FXS Gateway outbound route on Elastix. Path: PBX→Outbound Routes→Add Route Figure 18. Add Outbound Route Set the prefix as 9, choose the trunk "NeoGate" which is created above, then users should dial 9+number to call the phone which is connected to NeoGate TA3200.