Advertisement
Installation and Assembly:
Dual Arm Desktop Mount with Desk Clamp and Grommet for
19" - 30" LCD Screens
Models: LCT620AD
GROMMET INSTALLATION
DESK CLAMP INSTALLATION
Max Load Capacity per arm: 15 lbs (6.8 kg)
2300 White Oak Circle • Aurora, Il 60502 • (800) 865-2112 • Fax: (800) 359-6500 • www.peerless-av.com
ISSUED: 07-25-11 SHEET #: 090-9205-5 11-30-12
Advertisement
Table of Contents
Related Manuals for peerless-AV LCT620AD
Summary of Contents for peerless-AV LCT620AD
- Page 1 19" - 30" LCD Screens Models: LCT620AD GROMMET INSTALLATION DESK CLAMP INSTALLATION Max Load Capacity per arm: 15 lbs (6.8 kg) 2300 White Oak Circle • Aurora, Il 60502 • (800) 865-2112 • Fax: (800) 359-6500 • www.peerless-av.com ISSUED: 07-25-11 SHEET #: 090-9205-5 11-30-12...
-
Page 2: Tools Needed For Assembly
NOTE: Read entire instruction sheet before you start installation and assembly. WARNING • Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please call Peerless customer care at 1-800-865-2112. -
Page 3: Parts List
Before you begin, make sure all parts shown are included with your product. Parts List LCT620AD Description A column assembly B double link arm assembly C grommet assembly D round rubber pads E square rubber pads F M4 x 12 mm phillips screw... - Page 4 Clamp Installation Method Grommet Installation Method Remove clamp assembly from column assembly Apply four rubber pads (D, E) to bottom of column (A) as shown in fi gure 1.1. Remove mounting plate assembly (A) as shown below. Attach column from grommet assembly (C) and attach to column assembly (A) to mounting surface with a maximum assembly (A) with four M6 x 8mm screws using thickness of 3".
- Page 5 Attaching Adapter Plate to Screen WARNING • Tighten screws so adapter plate is fi rmly attached. Do not tighten with excessive force. Overtightening can cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become detached.
-
Page 6: Set Screw
Insert dual arm support (P) onto column assembly (A) fl ush against lock collar as shown in fi gure 5.1. Loosen and position lock collar to desired height and retighten. Insert arm assembly (B) onto dual arm support (P) as shown in fi gure 5.2. Tighten set screws on dual arm support (P) and arm assembly (B) using 2.5mm allen wrench (J) as shown in fi... - Page 7 Reinstall knobs through back of arm assemblies (B) and secure into back of adapter plates. Cables may be routed using cavity in arm assembly (B) and cable clip (K). Remove the cable cover on arm assembly (B) by pressing fi rmly in the middle of the cable cover and then pulling the fl anges of the cable cover. Route the cables in arm assembly (B) and then reinstall the cable cover.
- Page 8 To lock down rotation, tighten set screw shown in detail 2. To lock down tilt, tighten screw shown in detail 3. To lock down swivel, tighten screw shown in detail 4. To lock down height adjustment, tighten set screw shown in detail 5. TILT SCREW SET SCREW DETAIL 3...
-
Page 9: Limited Five-Year Warranty
Limited Warranty or impose any obligation on Peerless in connection with the sale of any Peerless® product. This warranty gives specifi c legal rights, and you may also have other rights which vary from state to state. www.peerless-av.com © 2012 Peerless Industries, Inc.
Need help?
Do you have a question about the LCT620AD and is the answer not in the manual?
Questions and answers