Table of Contents
Advertisement
8300 Low Energy Auto-Operator
Installation Instructions
I-EA00257 / 26790910
Installation and Service Manual
8300 Series Swing Door Operators
The manufacturer's specifications for this product require the installation to be approved by
an AAADM certified inspector.
Always visit www.hagerco.com for the latest Installation Instructions
Page 1 of 18
Rev 2, Rev Date: 1/30/19
HAGER COMPANIES 139 Victor Street, St. Louis, MO 63104 • (800) 325-9995
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for hager 8300 Series
Summary of Contents for hager 8300 Series
- Page 1 The manufacturer’s specifications for this product require the installation to be approved by an AAADM certified inspector. Always visit www.hagerco.com for the latest Installation Instructions Page 1 of 18 Rev 2, Rev Date: 1/30/19 HAGER COMPANIES 139 Victor Street, St. Louis, MO 63104 • (800) 325-9995...
-
Page 2: Table Of Contents
I-EA00257 / 26790910 Owner Information & Table of Contents The Hager Series 8300 Operator has been carefully designed, built, and tested to provide years of service. The life of the operator package is directly related to how carefully the installation is accomplished and how accurately the instructions are followed. -
Page 3: Product Description, Spec & Tools Required
I-EA00257 / 26790910 PRODUCT DESCRIPTION & SPECIFICATIONS The Hager 8300 series low energy auto-operators offer state-of-the-art micro-processed controllers with electro-mechanical drive. The unique slim-line design offers non-handed operation, full mechanical stops, and numerous interface options for sensors, push-plates, fire alarms and electric locks. The unit includes onboard diagnostics to simplify troubleshooting when needed. -
Page 4: Header Installation
2-1/16" 2-3/8" 1.5" Bottom of operator flush w/ bottom of frame Always visit www.hagerco.com for the latest Installation Instructions Page 4 of 18 Rev 2, Rev Date: 1/30/19 HAGER COMPANIES 139 Victor Street, St. Louis, MO 63104 • (800) 325-9995... - Page 5 6 for operator handing and arm type. Key slot configuration and location screw mounted to back-plate. Always visit www.hagerco.com for the latest Installation Instructions Page 5 of 18 Rev 2, Rev Date: 1/30/19 HAGER COMPANIES 139 Victor Street, St. Louis, MO 63104 • (800) 325-9995...
-
Page 6: Handing
EXTERIOR PULL SIDE MOUNTING WITH TRACK ARM INTERIOR INTERIOR EXTERIOR EXTERIOR Always visit www.hagerco.com for the latest Installation Instructions Page 6 of 18 Rev 2, Rev Date: 1/30/19 HAGER COMPANIES 139 Victor Street, St. Louis, MO 63104 • (800) 325-9995... -
Page 7: Push Arm Install
6" 19" 7" 20" 8" 21" DEEPER REVEAL REQUIRES ARM EXTENSION Always visit www.hagerco.com for the latest Installation Instructions Page 7 of 18 Rev 2, Rev Date: 1/30/19 HAGER COMPANIES 139 Victor Street, St. Louis, MO 63104 • (800) 325-9995... -
Page 8: Pull Arm Install
When completed, the end caps to the track can be installed. Always visit www.hagerco.com for the latest Installation Instructions Page 8 of 18 Rev 2, Rev Date: 1/30/19 HAGER COMPANIES 139 Victor Street, St. Louis, MO 63104 • (800) 325-9995... -
Page 9: Mechanical Stop Adjustment
It is recommended to place the door in the desired open or closed position then slide the required stop until it hits the internal stop point screw. Always visit www.hagerco.com for the latest Installation Instructions Page 9 of 18 Rev 2, Rev Date: 1/30/19 HAGER COMPANIES 139 Victor Street, St. Louis, MO 63104 • (800) 325-9995... -
Page 10: A/C Wiring
Ensure all incoming electrical power is shut off before proceeding with any wiring to Hager 8300 operator. Use only with wire harness provided; failure to do so may result in damage to equipment or personal harm as well as voiding the warranty. -
Page 11: Control Boards
**** See Page 14 for SW2 dip switch settings. ***** Required to maintain programmed settings. Always visit www.hagerco.com for the latest Installation Instructions Page 11 of 18 Rev 2, Rev Date: 1/30/19 HAGER COMPANIES 139 Victor Street, St. Louis, MO 63104 • (800) 325-9995... -
Page 12: Commisioning
Speed and time adjustment changes will not take effect until the door closes fully after the adjustment has been made. Additional adjustments are available with the Hager programmer (part number 2-679-0907) Always visit www.hagerco.com for the latest Installation Instructions... -
Page 13: Paired Operators
Door #1, and a sync line will be connected to Door #2. For simultaneous pairs, Hager provides a dual harness standard for the On-Off-Hold switch. Each plug- in connector for the control is wired in parallel to the On-Off-Hold switch located in the header end-cap. -
Page 14: Fire Rated Applications
Only fire rated hardware shall be used on a fire rated door & frame assembly. Always visit www.hagerco.com for the latest Installation Instructions Page 14 of 18 Rev 2, Rev Date: 1/30/19 HAGER COMPANIES 139 Victor Street, St. Louis, MO 63104 • (800) 325-9995... -
Page 15: Sw2 Dipswitch Settings
(Default) 10 Factory Use Only * Hager requires the use of a door-mounted safety device when dip switch 4 & 9 are on-enabled. Always visit www.hagerco.com for the latest Installation Instructions Page 15 of 18 Rev 2, Rev Date: 1/30/19... -
Page 16: J4, J5, And J6 Terminal Inputs
N.O. output is closed upon closed contact from fire alarm. LED 2 also illuminates. (+) 24VDC 1 A. Max Current Common Ground Always visit www.hagerco.com for the latest Installation Instructions Page 16 of 18 Rev 2, Rev Date: 1/30/19 HAGER COMPANIES 139 Victor Street, St. Louis, MO 63104 • (800) 325-9995... -
Page 17: Wiring Diagram
EXTERIOR 20 21 22 23 24 25 26 Hager Actuator Plates Always visit www.hagerco.com for the latest Installation Instructions Page 17 of 18 Rev 2, Rev Date: 1/30/19 HAGER COMPANIES 139 Victor Street, St. Louis, MO 63104 • (800) 325-9995... -
Page 18: Troubleshooting
Installation Instructions I-EA00257 / 26790910 Programming Device & Troubleshooting Please note, some functions of the Hager 8300 operator require the use of an optional hand-held programming device. The following functions require use of this device for programming: Logic Assignment For Inputs ...
Need help?
Do you have a question about the 8300 Series and is the answer not in the manual?
Questions and answers