Advertisement
CONTENTS
1. HEADER & TRACK ASSEMBLY
2. END BRACKET PLAIN
3. FLOOR PLATE
4. SPLIT STUD
5. CARRIER (9827)
6. QUICK RELEASE PLATE (9610)
7. DOOR GUIDE SET (9883)
8. BUMPER KIT (9881)
9. #8 X 3/4" PPHS
10. #8 X 1" PPHS
11. #8 X 5/8" TPHS
12. PULL
(SOLD SEPERATLY)
1
6'-7" Door
8'-0" Door
8"-6" Door
Construct the rough opening by following the guidelines in
the table above:
The minimum rough opening height from the finished floor
to the top of the door frame should be 101-1/2" for an 8'-0"
door and adjust accordingly from Table 1 above for different
door heights.
The rough opening width should equal two times the door
width plus 1" (25.4mm). For example, a 30" (76.2 cm) door
multiplied by two equals 60" (152.4 cm) plus 1" equals 61"
(154.94 cm) rough opening width. Refer to Table 2 on page
2 for all other door width dimensions.
Next, plumb the rough studs and ensure that the floor is
level.
Rev 2, Rev Date: 11/20/17
1
2
2
6
2
2
1
1
1
8
2
1
Opening Dimensions From Door Height (Table 1)
Rough opening height
Hager Companies 139 Victor Street, St. Louis, MO 63104 (800) 325-9995 www.hagerco.com
Sliding Door Hardware – 9850 – Pocket Frame
2.
3.
11.
Bracket Nail Height
84-1/2"
101-1/2"
107-1/2"
Installation Instructions
1.
4.
5.
10.
9.
6.
Bottom of Track to Floor
81-1/4"
98-1/4"
104-1/4"
I-SD00333
8.
7.
81"
98"
104"
Page 1 of 6
Advertisement
Table of Contents
Related Manuals for hager 9850
Summary of Contents for hager 9850
- Page 1 2 for all other door width dimensions. Next, plumb the rough studs and ensure that the floor is level. Rev 2, Rev Date: 11/20/17 Page 1 of 6 Hager Companies 139 Victor Street, St. Louis, MO 63104 (800) 325-9995 www.hagerco.com...
- Page 2 1/8” (3.17 mm) of the nail is left protruding. The slot in the end brackets will slide over these nails. Rev 2, Rev Date: 11/20/17 Page 2 of 6 Hager Companies 139 Victor Street, St. Louis, MO 63104 (800) 325-9995 www.hagerco.com...
- Page 3 Note: for additional clearance, floor plates may be cut and spread apart. Shims may also be inserted between header assembly and split studs. Or, you can use Hager’s 9634 door adaptor kit (sold separately), which contains shims and wider floor plates for additional clearance with 1-3/4” thick doors.
- Page 4 Opening door edge, secure bumper as close to dead center on pocket edge of door or back pocket jam. Pocket end Opening end Note: when installing bi-parting doors change opening distance to 3-3/4” from edge of door. Rev 2, Rev Date: 11/20/17 Page 4 of 6 Hager Companies 139 Victor Street, St. Louis, MO 63104 (800) 325-9995 www.hagerco.com...
- Page 5 After, using wrench provided adjust door hangers for height above the floor and to square door to solid jamb by turning the adjusting bolt on each hanger Rev 2, Rev Date: 11/20/17 Page 5 of 6 Hager Companies 139 Victor Street, St. Louis, MO 63104 (800) 325-9995 www.hagerco.com...
- Page 6 Install Door guides to finish split jamb and adjust to within 1/16” of door on either side sedrf sdfs Rev 2, Rev Date: 11/20/17 Page 6 of 6 Hager Companies 139 Victor Street, St. Louis, MO 63104 (800) 325-9995 www.hagerco.com...
Need help?
Do you have a question about the 9850 and is the answer not in the manual?
Questions and answers