Husqvarna Automower 105 Operator's Manual

Hide thumbs Also See for Automower 105:

Advertisement

Operator's manual
®
Husqvarna Automower
105
Read the operator's manual carefully and make sure that you
EN, English
understand the instructions before you use the product.

Advertisement

Table of Contents
loading

Summary of Contents for Husqvarna Automower 105

  • Page 1 Operator's manual ® Husqvarna Automower Read the operator's manual carefully and make sure that you EN, English understand the instructions before you use the product.
  • Page 2: Table Of Contents

    Contents 7.2 Storage.............41 1 Introduction 7.3 Disposal............41 1.1 Support............3 8 Technical data 1.2 Product description........3 8.1 Technical data.......... 42 2 Safety 9 Warranty 2.1 Safety definitions........9 2.2 General safety instructions......9 9.1 Warranty terms.........44 2.3 Safety instructions for operation....11 10 EC Declaration of Conformity 3 Installation 10.1 EC Declaration of Conformity....45 3.1 Introduction - Installation......
  • Page 3: Introduction

    1 Introduction Serial number: PIN code: The serial number is on the product rating plate and on the product carton. • Use the serial number to register your product on www.husqvarna.com. 1.1 Support automatically. Collection of grass is not necessary. ®...
  • Page 4 1.2.1 Product overview The numbers in the figure represent: 11. Chassis box with electronics, battery and motors Body 12. Main switch Hatch to display, keypad and cutting height 13. Rear wheel adjustment 14. Charging strip Stop button 15. Keypad Contact strips 16.
  • Page 5 22. Extra blades WARNING: Read the 23. Operator’s Manual and Quick Guide user instructions before operating the product. 24. Measurement gauge for help when installing the boundary wire (the measurement gauge is broken loose from the box) WARNING: Operate the 25.
  • Page 6 It is not permitted to dispose this The settings function is where the product as normal household waste. general settings for the products are Ensure that the product is recycled in set. accordance with local legal requirements. The product will not cut the grass due to the timer function.
  • Page 7 1.2.5 Menu structure overview Timer Work Work Work Reset hours 1 hours 2 days timer Installation Guide width Remote start 1 Remote start 2 Test Drive past settings wire Narrow Medium Wide Test in Test out Remote Remote Proportion Distance start 1 start 2 Never...
  • Page 8 1.2.6 Display The display on the product shows information and settings of the product. To access the display, push the STOP button. 1.2.7 Keypad The keypad consists of 4 groups of buttons: • The START button is used to activate the product.
  • Page 9: Safety

    2 Safety 2.1 Safety definitions 2.2 General safety instructions Warnings, cautions and notes are used to point The following system is used in the Operator’s out specially important parts of the manual. Manual to make it easier to use: italics is a text that is shown •...
  • Page 10 2.2.1 IMPORTANT. READ CAREFULLY BEFORE USE. KEEP FOR FUTURE REFERENCE The operator is responsible for accidents or hazards occurring to other people or property. This appliance is not intended for use by persons (including chil- dren) with reduced physical, sensory or mental capabilities (that could affect a safe handling of the product), or lack of experience and knowledge, unless they have been given supervision or in- struction concerning use of the appliance by a person responsible...
  • Page 11: Safety Instructions For Operation

    WARNING: The product Warning! Automatic lawnmower! Keep away from the machine! Supervise children! can be dangerous if used incorrectly. Warning! WARNING: Do not use Automatic lawnmower! Keep away from the machine! the product when Supervise children! persons, especially children, or animals, are in the work area.
  • Page 12 To do the timer run simultaneously. Refer to settings on page 20 . ® • Husqvarna does not guarantee full compatibility between the product and other types of wireless systems such as remote controls, radio transmitters, hearing loops, 12 - Safety...
  • Page 13 Carry the product by the handle under the Inspect the product each week and replace any product with the blade disc away from the damaged or worn parts. Refer to Maintenance on page 28 . body. 2.3.5 In the event of a thunderstorm CAUTION: Do not lift the product when it is parked in the charging station.
  • Page 14: Installation

    • Put the charging station on a level surface. Note: Refer to www.husqvarna.com for more Max 3 cm / 1.2" information about installation. 3.2 Before the installation of the wires You can select to attach the wires with stakes or bury them.
  • Page 15 3.3.2 To examine where to put the power recommended to make an eyelet where the guide wire will be connected. Make the eyelet with supply approximately 20 cm / 8 in. of the boundary wire. • Put the power supply in an area with a roof and protection from the sun and rain.
  • Page 16 0-15% 0-15 cm / 0-6" 100 cm / 40" 25 cm / 10" > 5 cm/>2" • For slopes steeper than 15% inside the work area, isolate the slope with boundary wire. • Put the boundary wire 20 cm / 8 in. (C) from •...
  • Page 17 0 cm / 0" CAUTION: Do not put a section of • Put the boundary wire around the secondary boundary wire across the other. area (B) to make an island. Refer to The sections of boundary wire make an island on page 16 . must be parallel.
  • Page 18: Installation Of The Product

    CAUTION: The product is only to behind the charging station. be used with the power supply ® unit supplied by Husqvarna CAUTION: Do not put unwanted wire in a coil. The coil causes interference with the product. WARNING: Do not put the power...
  • Page 19: To Put The Wire Into Position With Stakes

    Note: Make sure that you can see the end of the guide wire through the transparent area of the coupler. Push the button on the coupler with an adjustable pliers. CAUTION: Twinned cables, or a screw terminal block that Close the connector with a pair of pliers. is insulated with insulation tape are not satisfactory Cut the boundary wire 1-2 cm / 0.4-0.8 in.
  • Page 20: To Extend The Boundary Wire Or The Guide Wire

    3.7 To extend the boundary wire or the 3.8.2 To do the basic settings guide wire Before you start the product for the first time, you must do the basic settings and calibrate the Note: Extend the boundary wire or the guide wire product.
  • Page 21 The guide width is a measure of how far from the Model Approximate operation ca- guide wire the product is allowed to travel when it pacity, m /h / yd follows this to and from the charging station. The ® Automower 43 / 50 area beside the wire which the product uses is...
  • Page 22 • Rarely (approx. 20%) To do a test of the Remote start function • Medium (approx. 50%) Put the product in the charging station. • Often (approx. 80%) To get access to the menu Do steps 1-3 in • Always (100%) on page 20 .
  • Page 23 of the product. If the incorrect PIN-code is 3.9.5 Settings entered 5 times, the product is locked for some time. The lock is extended for each new incorrect try. • Time lock - The product is locked if the PIN- code has not been entered in 30 days.
  • Page 24 Use the multi-choice buttons to move through the menu structure Settings > Language. Use the multi-choice buttons to select OK . language and then push 3.9.5.4 To set the country Do steps 1–3 in To get access to the menu on page 20 .
  • Page 25: Operation

    4 Operation 4.1 Main switch Close the hatch. Note: If the product is parked in the charging WARNING: Read the safety instructions carefully before you start station, the product will only leave the charging station when the battery is fully charged and if the the product.
  • Page 26: To Stop The Product

    When the battery is empty, the product stops and 4.6.1 Standby the message Needs manual charging shows in The product has an inbuilt standby period the product display. Put the product in the according to the Standby time table. The standby charging station to charge the battery.
  • Page 27: To Charge The Battery

    period must in total be according to the Standby Place the product in the charging station. time table. Refer to Standby on page 26 . Open the hatch and slide the product in as far as possible to ensure proper contact Timer setting Period 1 (A): 06:00 - 17:00 between the product and the charging Timer setting Period 2 (C): 20:00 - 23:00...
  • Page 28: Maintenance

    CAUTION: Never use a high-pressure and servicing must be done according to washer or even running water to clean ® Warranty instructions from Husqvarna . Refer to the product. Never use solvents for terms on page 44 . cleaning. When the product is first used, the blade disc and blades should be inspected once a week.
  • Page 29: Replace The Blades

    5.3 Replace the blades WARNING: Use blades and screws of ® the right type. Husqvarna can only guarantee safety when using original blades. Only replacing the blades and reusing the screw can result in a screw wearing during mowing. The blades can then be propelled from under the Remove each blade and screw.
  • Page 30: Winter Service

    5.5 Winter service ® Take your product to your local Husqvarna representative for service prior to winter storage. Regular winter service will maintain the product in good condition and create the best conditions for a new season without any disruptions.
  • Page 31: Troubleshooting

    In this chapter, faults and symptoms are described and can guide you if the product does not operate as expected. More suggestions for steps to take in the event of malfunction or symptoms can be found on www.husqvarna.com. 6.2 Fault messages Below a number of fault messages are listed which may be shown in the display of the product.
  • Page 32 Wrong PIN code Wrong PIN code has been entered. Enter the correct PIN code. Contact ® Five attempts are permitted, and the Husqvarna customer service if you keypad is then blocked for five minutes. forget the PIN code. No drive...
  • Page 33 Message Cause Action Upside down The product is leaning too much or has Turn the product the right way up. turned over. Needs manual The product is set to the Secondary Place the product in the charging sta- charging area operating mode. tion.
  • Page 34 Message Cause Action Temporary battery Temporary battery or firmware related Restart the product. problem issue in the product. Disconnect and reconnect the battery. Battery problem If the problem remains, the message requires action by authorized service technician. Charging current Wrong or faulty power supply unit. Restart the product.
  • Page 35: Information Messages

    6.3 Information messages Below a number of information messages are listed which may be shown in the display of the product. ® Contact Husqvarna customer service if the same message appears often. Message Cause Action Low battery The product cannot find the charging Check that the charging station and the station.
  • Page 36: Indicator Lamp In The Charging Station

    For a fully functional installation, the indicator lamp in the charging station must emit a solid green light. If something else appears, follow the troubleshooting guide below. ® If you still need help with troubleshooting, please contact your local Husqvarna representative. Light...
  • Page 37: Symptoms

    6.5 Symptoms If your product does not work as expected, follow the symptoms guide below. There is a FAQ (Frequently Asked Questions) on www.husqvarna.com which provides more detailed ® answers to a number of standard questions. Contact Husqvarna customer service if you still cannot find the reason for the fault.
  • Page 38: Find Breaks In The Loop Wire

    Symptoms Cause Action To re- Both the mowing The battery is spent. Replace the battery. Refer to move the battery on page 41 . and charging times are shorter than usual. The product is The product has an inbuilt standby peri- No action.
  • Page 39 A wire break can be located by gradually halving the distance of the loop where the break may have occurred until there is only a very short section of the wire left. The following method does not work if mode is activated. Make sure first that ECO mode is turned off.
  • Page 40 between a solid green light and a flashing blue light. Then follow instruction in step 5 below. If indicator lamp still flashes blue in step 3 above: Put L and GUIDE back in their original positions. Then switch R and GUIDE.
  • Page 41: Transportation, Storage And Disposal

    7 Transportation, storage and disposal 7.1 Transportation Remove the 4 screws to the battery cover (Torx 20) and remove the battery cover. The supplied Li-ion batteries obey the Dangerous Goods Legislation requirements. • Obey all applicable national regulations. • Obey the special requirement on package and labels for commercial transportations, including by third parties and forwarding agents.
  • Page 42: Technical Data

    8 Technical data 8.1 Technical data ® Automower Dimensions Length, cm / in 55 / 21.7 Width, cm / in 39 / 15.4 Height, cm / in 25 / 9.8 Weight, kg / lbs 6.9 / 15 ® Automower Electrical system Battery, Lithium-Ion 18 V/2.1 Ah Art.No 586 57 62-01, 586 57 62-02, 586 57 62-04...
  • Page 43 ® Automower Mowing Cutting system 3 pivoted cutting blades Blade motor speed, rpm 2900 Power consumption during cutting, W +/- 20 % Cutting height, cm / in 2-5 / 0.8-2 Cutting width, cm / in 17 / 6.7 Narrowest possible passage, cm / in 60 / 24 Maximum angle for work area, % Maximum angle for boundary wire, %...
  • Page 44: Warranty

    The blades and wheels are seen as disposable and are not covered by the warranty. ® If an error occurs with your Husqvarna product, ® please contact Husqvarna customer service for further instructions.
  • Page 45: Ec Declaration Of Conformity

    10 EC Declaration of Conformity 10.1 EC Declaration of Conformity Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declares that the robotic ® lawn mowers Husqvarna Automower 105 with serial numbers dating 2018 week 44 and Lars Roos onwards (the year and week is clearly stated on the rating plate, followed by the serial number), Global R&D Director, Robotic category...
  • Page 46 46 - EC Declaration of Conformity 1285 - 002 - 20.08.2019...
  • Page 47 1285 - 002 - 20.08.2019 EC Declaration of Conformity - 47...
  • Page 48 ® AUTOMOWER is a trademark owned by Husqvarna AB. © Copyright 2019 HUSQVARNA. All rights reserved. www.husqvarna.com Original instructions 1141861-26 2019-09-05...

Table of Contents