Table of Contents
Advertisement
SOLUTION XT UNIT MODEL NOMENCLATURE
FIGURE 1 - Cutaway of Solution XT Showing Segmented Construction ................................................................ 15
FIGURE 2 - AHU and Coil Hand Identification ........................................................................................................16
FIGURE 3 - AHU ID Label .......................................................................................................................................17
FIGURE 4 - Skid ID Label .......................................................................................................................................17
FIGURE 5 - Example of Segment Id Box ................................................................................................................17
FIGURE 6 - Example of Moisture Eliminator Loose Component ID Label .............................................................. 19
FIGURE 7 - Example of Hood Loose Component ID Label ....................................................................................19
FIGURE 8 - Filter ID Label ......................................................................................................................................19
FIGURE 9 - Metal Spacers on Solution XT Doors ...................................................................................................23
FIGURE 10 - Recommended Lifting with Multiple Points ........................................................................................24
FIGURE 11 - Typical Come-A-Longs .......................................................................................................................24
FIGURE 12 - Proper Lifting with Shackle with Corner Connector Corners ............................................................. 24
FIGURE 13 - Proper Lifting with Shackle at Lifting Lug...........................................................................................25
FIGURE 14 - Proper Lifting with Base Rail..............................................................................................................25
FIGURE 15 - Minimum Service Clearances ............................................................................................................26
FIGURE 16 - Typical Curb Assembly ......................................................................................................................27
FIGURE 17 - Solution XT No Base Rail - Housekeeping Pad Required to Accomodate Trap Height ..................... 28
FIGURE 18 - No Housekeeping Pad - Solution XT Base Rail Required to Accomodate Trap Height ..................... 28
FIGURE 19 - With Base or Base Rail and Housekeeping Pad ...............................................................................28
FIGURE 20 - Ceiling Suspended AHU on Structural Steel......................................................................................29
FIGURE 21 - Tools Needed to Assemble Shipping Splits .......................................................................................30
FIGURE 22 - Second Tier Tie-Down Fastener Pack (P/N 386-03419-000) ............................................................ 30
FIGURE 23 - Bottom Raceway Shipping Split Fastener Pack (P/N 386-03418-000).............................................. 31
FIGURE 24 - Base Rail Shipping Split Fastener Pack (P/N 386-03417-000) ......................................................... 31
FIGURE 25 - Top Raceway Bracket Assembled (P/N 386-04747-000) ................................................................... 31
FIGURE 26 - Neoprene Gasket - 1/4 In. X 2 In. X 25 Ft (P/N 028-11883-010) ....................................................... 31
FIGURE 27 - Neoprene Gray Gasket - 1/4 In X 3/4 In X 35 Ft (P/N 028-11873-010) for Door .............................. 31
FIGURE 28 - Phillips Hex Head Screw (P/N 021-32268-011) For Indoor Unit Seam Cap ...................................... 31
FIGURE 29 - Hex Head Screw For Outdoor Roof Seam Cap, Pipe Chase, and Rain Hood - 1/4 In-14 X 1 In (P/N
021-30530-052) .................................................................................................................................32
FIGURE 30 - Butyl Tape - 3/16 In X 3/4 In X 40 Ft (P/N 013E-03327-010) ............................................................. 32
Pipe Chase Only ................................................................................................................................32
FIGURE 32 - Roof Seam Cap (Assembled) ............................................................................................................32
FIGURE 33 - Pipe Chase, Trim Angle, and Cover...................................................................................................32
FIGURE 34 - Hood ..................................................................................................................................................33
FIGURE 35 - Damper Shaft Extension Kit (P/N 026-33715-002) ............................................................................33
FIGURE 36 - Corner Connector Hole Plug (P/N 021-19568-000) (8) .....................................................................33
FIGURE 37 - Touch-Up Spray - 12 Oz. (P/N 013-03322-000) ................................................................................33
FIGURE 38 - Shipping Split Corner Gasket - 3.5 X 3. 5 (P/N 028-11883-010) ...................................................... 33
FIGURE 39 - Spare Fan Belt ...................................................................................................................................33
FIGURE 40 - Conduit (P/N 025-39024-001) and SJO Cord (P/N 025-35746-001) ................................................. 33
FIGURE 41 - Shipping Split Examples ....................................................................................................................35
FIGURE 42 - Shipping Split Examples Using Structural Steel Baserails ................................................................ 35
FIGURE 43 - Applying Gasket Square, Neoprene Gasket and Caulk to Raceway Split ......................................... 36
FIGURE 44 - Typical Come-A-Longs ......................................................................................................................36
FIGURE 45 - Electrical Connector (Not Connected) ...............................................................................................36
8
LIST OF FIGURES
FORM 102.20-N1
ISSUE DATE: 7/06/2016
JOHNSON CONTROLS
Hide quick links:
Advertisement
Table of Contents
