Crosswater GLIDE II Series Manual

Crosswater GLIDE II Series Manual

Bathroom furniture

Advertisement

Quick Links

500 Two Drawer Basin Unit,

Ceramic / Cast Marble Basin / Worktop
x2
Tools & equipment needed: Drill, 8mm Suitable drill bit, Phillips screwdriver, Spirit level, Ruler/tape measure, Pencil,
Silicone sealant (clear).
IMPORTANT - Advice and safety - Please read before installation
Please read these instructions carefully before starting installation
and keep in a safe place for future reference. ENSURE the room is well
heated and ventilated.
Check the contents of the pack carefully before installation. Bauhaus will
If any fault is found with materials or workmanship, it must be reported
immediately to the manufacturer. Remedial action will be taken, based on
information received, on condition that: 1. Full details are supplied to the
3. The manufacturer is informed of any damage/shortages prior to
installation. 4. The product has not been installed, or attempts have been
made to install.
We do not accept responsibility for any problems that may occur through
incorrect installation.
Advice & Safety
product guarantee maybe considered invalid. For a claim made under our
unnecessary damage occurring.
It is recommended that the furniture and accessories are installed after
product to be easily removed if required in the future.
This document has been prepared for your guidance, you must exercise
due care at all times.
Please note that some units are heavy. Always take care when lifting, and
follow health and safety guidelines. It is recommended that 2 people carry
out the installation of larger basin/vanity units over 30Kgs gross weight.

INSTALLATION INSTRUCTIONS

BATHROOM FURNITURE RANGE

700 Two Drawer Basin Unit,

Ceramic / Cast Marble Basin / Worktop
DE0002SCW
DE0002SRW
GL5000T
GL5000D+
x8
y product has
Plumber/
can be required.
tting to avoid
DE0003SCW
DE0003SRW
GL7000T
GL7000D+
x2
x8
Warning! Please check for any hidden pipes or electrical cables before
When using power tools always follow the manufacturer's user instructions.
studded/plasterboard walls, please use appropriate plasterboard
Please ensure the wall can take weight of units detailed above. Before
installing a wooden bathroom unit into a new property, extension or recently
plastered room we strongly advise the building/room is completely dry, well
ventilated and adequately heated.
Important pre-installation notes
To ensure full working use of the drawers we recommend the use of
Bauhaus basin furniture trap BTR0410W.
Care & Cleaning
Cast mineral marble products should be cleaned regularly with warm soapy
water, then rinsed with clean water and, if desired, dried and polished with
a soft cloth. Lime scale deposits can be removed using a 50:50 solution of
warm water and lime scale remover and soft clean cloth. We recommend
regular cleaning with Bauhaus Cream Polish SD150RW, specially
formulated to clean and help protect the surface of cast mineral marble
basins.
Do not use abrasive cleaners or bleach in this will permanently damage the
high gloss surface.
carcasses.
If any maintenance is required then it must be carried out by a
Plumber.
prior notice.
GLIDE II
1000 Two Drawer Basin Unit,
Ceramic / Cast Marble Basin / Worktop
DE0004SCW
DE0004SRW
x2
bathroom has
urniture
GL1000T
GL1000D+
x8
ions without
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the GLIDE II Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Crosswater GLIDE II Series

  • Page 1 GLIDE II BATHROOM FURNITURE RANGE 500 Two Drawer Basin Unit, 700 Two Drawer Basin Unit, 1000 Two Drawer Basin Unit, Ceramic / Cast Marble Basin / Worktop Ceramic / Cast Marble Basin / Worktop Ceramic / Cast Marble Basin / Worktop DE0003SCW DE0004SCW DE0002SCW...
  • Page 2 801 02 Z1 IN www.camar.i t /warning Basin & Basin Unit Installation 4800 1200 Step 1 Step 2 Removing the drawer Plan unit position Pull firmly horizontally until Pull the drawer out, lift slightly Decide on the position and height of the unit. The recommended aprox.
  • Page 3 Step 4 a: Check the unit is level. If levelling is required, use a screwdriver to adjust the hanging position, as follows: b: To lift or lower the unit, adjust the screw shown. c: To move the unit closer or further from the wall, adjust the screw shown.
  • Page 4 RUNNER FITTINGS Step 2 Step 1 Drawer front installation Removing the drawer front Insert the drawer front into the drawer Insert the screwdriver in the left screw sides. The panel engages and slide it to the left. automatically and is fixed. The drawer front is now released and can be removed.
  • Page 5 The drawer in installation. For any further information please contact Bauhaus on: 0345 873 8840 Or visit our web-site at: www.crosswater.co.uk The manufacturer reserves the right to make technical Crosswater Glide II Single Drawer Unit.indd 5 28/2/12 13:35:27...

This manual is also suitable for:

7005001000

Table of Contents