Related Manuals for Pepperl+Fuchs PMI360DV-F130-IU2E2-V15
Summary of Contents for Pepperl+Fuchs PMI360DV-F130-IU2E2-V15
- Page 1 FACTORY AUTOMATION MANUAL PMI360DV-F130-IU2E2- Inductive angle positioning system...
- Page 2 PMI360DV-F130-IU2E2-V15 With regard to the supply of products, the current issue of the following document is ap- plicable: The General Terms of Delivery for Products and Services of the Electrical Indus- try, published by the Central Association of the Electrical Industry (Zentralverband Elektrotechnik und Elektroindustrie (ZVEI) e.V.) in its most recent version as well as the...
-
Page 3: Table Of Contents
PMI360DV-F130-IU2E2-V15 Introduction................. 5 Declaration of conformity ............6 Safety ................... 7 Used Symbols ..................7 Intended use..................7 General safety instructions ..............7 Product Description ..............8 Use and application ................8 Displays and controls................9 Delivery package.................. 9 Accessories ..................10 4.4.1... - Page 4 PMI360DV-F130-IU2E2-V15 Troubleshooting................ 21 Faults when programming the outputs ..........21 Faults during operation..............22 10 Disposal..................23...
-
Page 5: Introduction
PMI360DV-F130-IU2E2-V15 Introduction Introduction Congratulations You have chosen a device manufactured by Pepperl+Fuchs. Pepperl+Fuchs develops, produces and distributes electronic sensors and interface modules for the market of automation technology on a worldwide scale. Symbols used The following symbols are used in this manual: Note! This symbol draws your attention to important information. -
Page 6: Declaration Of Conformity
This product was developed and manufactured under observance of the applicable European standards and guidelines. Note! A Declaration of Conformity can be requested from the manufacturer. The product manufacturer, Pepperl+Fuchs GmbH, D-68307 Mannheim, has a certified quality assurance system that conforms to ISO 9001. ISO9001... -
Page 7: Safety
User modification and or repair are dangerous and will void the warranty and exclude the manufacturer from any liability. If serious faults occur, stop using the device. Secure the device against inadvertent operation. In the event of repairs, return the device to your local Pepperl+Fuchs representative or sales office. Note! Disposal Electronic waste is hazardous waste. -
Page 8: Product Description
The PMI360DV-F130-IU2E2-V15 has an analog output for the indication of angular positions. For high resistance loads (>3.3 k), the angular position will output a voltage value 0 ... 10 V DC and for low resistance loads (<400 ), a current value 4 ... -
Page 9: Displays And Controls
LED indicators Programming buttons 4 LEDs and 3 programming buttons are located on top of the PMI360DV-F130-IU2E2-V15. The central, front "Power/Error" LED is a 2-color LED that lights up or flashes green (normal operation) or red (fault) depending on the operating state of the device. The LEDs "S1", "S2"... -
Page 10: Accessories
PMI360DV-F130-IU2E2-V15 Product Description Accessories Various accessories are available. 4.4.1 Connecting cable You can use the following cables for the electrical connection: M12 x 1 connectors, 5-pin Figure Material Length Order designation M12 x 1, straight, 5-pin V15-G-2M-PVC V15-G-5M-PVC 10 m... -
Page 11: Installation
PMI360DV-F130-IU2E2-V15 Installation Installation Note on safety Warning! Risk of short circuit Injuries and damage to the device are possible when working with live parts. Before working on the device, always disconnect the supply voltage. ■ Connect the device to the supply voltage only after completion of the work. - Page 12 PMI360DV-F130-IU2E2-V15 Installation Dimensions when using a different actuating element Drive shaft Insulation ring made from non-conductive material Separate actuator (L mm) Sensitive surface on the sensors (black, cylindrical inner surface) Sensor Insert the shaft until actuator C and the sensitive surface on sensor D overlap as far as possible.
-
Page 13: Electrical Connection
4. Check that the wires are connected correctly before connecting the cordset to the sensor. On Pepperl+Fuchs cordsets, the wire colors are assigned to the connecting pins in the connector according to DIN EN 60947-5-2. 5. Attach the socket on the cordset to the connector on the sensor and tighten the union nut by hand. -
Page 14: Commissioning
PMI360DV-F130-IU2E2-V15 Commissioning Commissioning Programming the switching outputs 2 switching zones with a zone width of 5° are preset at the factory. The switching zones lie between the angle settings 120°... 125 ° (S1) and 240° ... 245° (S2). You can modify the position and width of these switching zones by programming them accordingly. -
Page 15: Programming The Analog Output
PMI360DV-F130-IU2E2-V15 Commissioning Programming switching output S2 The switching output 2 (S2) is programmed in the same way. Press the S2 button. The S2 LED indicates the status. Note! Activating the keylock The keylock is not activated initially. Press any button on the sensor briefly to determine whether the keylock is active. - Page 16 PMI360DV-F130-IU2E2-V15 Commissioning Note! Programming an angle segment of exactly 45° If you intend to program an angle segment of exactly 45° for the analog output, you can make use of the restriction that prevents the angle segment from being below 45°...
-
Page 17: Output Function In Normal Operation
PMI360DV-F130-IU2E2-V15 Output function in normal operation Output function in normal operation Example I/U2 I/U1 0° 90° 180° 270° 360° 20° 60° I/U2 I/U1 Figure 7.1 Output function depends on the position of the actuator and the method used to program the outputs. -
Page 18: Function Of Switching Outputs S1 And S2
PMI360DV-F130-IU2E2-V15 Output function in normal operation Voltage output: If the measurement range is exceeded, the analog output value retains the last displayed value until the position of the actuator falls within the analog measurement range again (shown in the example). - Page 19 PMI360DV-F130-IU2E2-V15 Output function in normal operation Voltage output: After the measurement range is exceeded, the analog output value retains the last displayed value until the position of the actuator falls within the analog measurement range again (depending on the rotation direction, i.e. 0 V or 10 V).
-
Page 20: Maintenance And Repair
S0 = 0 ° S2 = 240° - 245° S1 = 120° - 125° Default setting PMI360DV-F130-IU2E2-V15 Reset process 1. Press and hold the sensor button assigned to the output that you would like to reset. The associated yellow LED starts to flash slowly after 2 seconds. -
Page 21: Troubleshooting
PMI360DV-F130-IU2E2-V15 Troubleshooting Troubleshooting Faults when programming the outputs If unexpected situations occur when the outputs of the inductive angular positioning system are programmed, refer to the table below for possible causes and instructions for rectifying the problem. State Possible cause Action The buttons do not unlock. -
Page 22: Faults During Operation
PMI360DV-F130-IU2E2-V15 Troubleshooting Faults during operation If the inductive angular positioning system does not function correctly, refer to the table below for possible causes and instructions for rectifying the problem. Error Possible cause Action "Power/Error" LED does not The power supply is switched... -
Page 23: Disposal
PMI360DV-F130-IU2E2-V15 Disposal Disposal Electronic waste is hazardous waste. When disposing of the equipment, observe the current statutory requirements in the respective country of use, as well as local regulations. The device does not contain any batteries that require separate disposal. - Page 24 Twinsburg, Ohio 44087 · USA Tel. +1 330 4253555 E-mail: sales@us.pepperl-fuchs.com Asia Pacific Headquarters Pepperl+Fuchs Pte Ltd. Company Registration No. 199003130E Singapore 139942 Tel. +65 67799091 E-mail: sales@sg.pepperl-fuchs.com www.pepperl-fuchs.com Subject to modifications / DOCT-1863B Copyright PEPPERL+FUCHS • Printed in Germany 06/2015...